HomeMy WebLinkAboutMonitor Module June 15, 2004 JCI-6720
J HNSON M300MJ, M301 MJ,
CONTf� LS M302MJ, and M300DJ
Monitor Modules with FlashScanO
GENERAL U
Four different monitor modules are available for Johnson Con- [nn MARYLAND
trols'intelligent controls to suit a variety of applications. Moni- o � f IYI State Fire Marshal
tor modules are used to supervise a circuit of dry-contact Permit# 2029
input devices, such as conventional heat detectors and pull LISTED APPROVEQ (except M300DJ)
stations, or monitor and power a circuit of two-wire smoke S1570
detectors (M302MJ). California
M300MJ—is a standard-sized module t icall mounts State Fire
�yp y M EA O: Marshal
to a 4"[10.16 cm]square box)that supervises either a Class SEq�,�E 7300-0554:131 (M300MJ,
A (Style D) or Class B (Style B) circuit of dry-contact input 457-99-E Vol. III M301MJ, M302MJ)
devices. (except M300DJ)
7300-0554:144 (M300DJ)
M301MJ — is a miniature monitor module (a mere 1.3"
(3.302 cm)H x 2.75"(6.985 cm)W x 0.5"(1.270 cm)D)used
to supervise a Class B (Style B) circuit. Its compact design
allows the M301 MJ to often be mounted in a single-gang
box behind the device iYs monitoring. � O O � 9
M302MJ — is a standard-sized module used to monitor O �
and supervise compatible two-wire, 24 volt, smoke detec- ,
tors on a Class A(Style D) or Class B (Style B) circuit. � g 56�9�0 0 �
M300DJ—is a standard-sized dual monitor module used � g 3��Z � � M300MJ
to monitor and supervise two independent two-wire initiating z i3
device circuits(IDCs)at two separate,consecutive addresses � 7 TENS� 1514 2 � and
in intelligent, two-wire systems. � 6 4 678 9 3 � M302MJ
FlashScanO(U.S. Patent 5,539,389)is a new communi- 3
cation protocol developed by NOTIFIER Engineering that ❑ 5 2�0 4 �
ONES
greatly enhances the speed of communication between ana- �ooP ADDRESS
log intelligent devices. Intelligent devices communicate in a O
grouped fashion. If one of the devices within the group has � O O �
new information,the panel CPU stops the group poll and con- ��
centrates on single points. The net effect is response speed
greater than five times that of other designs.
FlashScanO is a registered trademark of NOTIFIER. ,
M300MJ MONITOR MODULE � 9 56�9,0 ° ❑
• Built-in type identification automatically identifies this de- detail of � 8 3��2 1 �
vice as a monitor module to the control panel. M300DJ � � 21 0 15143 2 �
• Powered directly by two-wire SLC loop.No additional power — note "ones" � 6 TE6 8 3 � .,
required. addresses are 4 �
• High noise (EMF/RFI) immunity. 0, 2, 4, 6, 8 OI71y � 5 z 4 �
• SEMS screws with clam in lates for ease of wirin on,es°
p� 9 P g� LOOP ADDRESS
• Direct-dial entry of address 01 – 159 on FlashScanO sys-
tems(IFC-640, IFC-3030),or 01 –99 on traditional systems ules in existing systems.
(IFC-400, IFC-640, IFC-1010/2020, IFC-3030, or FC-2000). M300MJ Applications—Use to monitor a zone of four-
• LED flashes green during normal operation (this is a pro- wire smoke detectors, manual fire alarm pull stations,
grammable option) and latches on steady red to indicate waterflow devices, or other normally-open dry-contact alarm
alarm. activation devices. May also be used to monitor normally-
The M300MJ Monitor Module is intended for use in intelli- open supervisory devices with special supervisory indica-
gent,two-wire systems,where the individual address of each tion at the control panel. Monitored circuit may be wired as
module is selected using the built-in rotary switches. It pro- an NFPA Style B (Class B) or Style D (Class A) Initiating
vides either a two-wire or four-wire fault-tolerant Initiating Device Circuit. A 47K ohm End-of-Line Resistor (provided)
Device Circuit(IDC)for normally-open-contact fire alarm and terminates the Style B circuit. No resistor is required for su-
supervisory devices.The module has a panel-controlled LED pervision of the Style D circuit. Maximum IDC loop length is
indicator.The M300MJ can be used to replace M500MJ mod- 2,500 ft./762 m (20 ohms maximum).
This document is not intended to be used for installation purposes.We try to keep our
product information up-to-date and accurate. We cannot cover all specific applications
or anticipate all requirements. All specifications are subject to change without notice.
J�HNSON For more information,contact your
Johnson Controls Field Support Center.
CONTR LS 507 East Michigan Street,Milwaukee,WI 53202
JCI-6720•06/15/04 —Page 1 of 6
M300MJ Operation—Each M300MJ uses one of 159 M301 MJ Operation—Each M301 MJ uses one of 159
available module addresses on an SLC loop. It responds to available module addresses on an SLC loop. It responds to
regular polls from the control panel and reports its type and regular polls from the control panel and reports its type and
the status (open/normal/short)of its Initiating Device Circuit the status (open/normal/short)of its Initiating Device Circuit
(IDC). A flashing LED indicates that the module is in com- (IDC).
munication with the control panel. The LED latches steady M301 MJ Specifications
on alarm (subject to current limitations on the loop).
Nominal operating voltage: 15 to 32 VDC.
M300MJ Specifications
Maximum operating current: 375 NA.
Nominal operating voltage: 15 to 32 VDC.
EOL resistance: 47K ohms.
Maximum current draw: 5.1 mA (LED on). Temperature range: 32°F to 120°F (0°C to 49°C).
Maximum operating current: 375 NA (LED flashing). Humidity range: 10% to 93% noncondensing.
EOL resistance: 47K ohms. Dimensions: 1.3"(3.302 cm)high x 2.75"(6.985 cm)wide x
Temperature range: 32°F to 120°F (0°C to 49°C). 0.5" (1.270 cm) deep.
Humidity range: 10% to 93% noncondensing. Wire length: 6" (15.24 cm) minimum.
�imensions: 4.5" (11.43 cm) high x 4" (10.16 cm) wide x M301MJ INTERFACE MODULE
1.25" (3.175 cm) deep. Mounts to a 4" (10.16 cm)square x
2.125" (5.398 cm) deep box. • Supports compatible two-wire smoke detectors.
M301MJ MINI MONITOR MODULE ' Supervises IDC wiring and connection of external power
source.
• Built-in type identification automatically identifies this de- . High noise (EMF/RFI) immunity.
vice as a monitor module to the panel. • SEMS screws with clamping plates for ease of wiring.
• Powered directly by two-wire FACP. No additional power . Direct-dial entry of address 01 – 159 on FlashScanO sys-
required. tems(IFC-640, IFC-3030),or 01 –99 on traditional systems
• High noise (EMF/RFI) immunity. (IFC-400, IFC-640, IFC-1010/2020, IFC-3030, or FC-2000).
• Tinned, stripped leads for ease of wiring. • LED flashes during normal operation (this is a program-
• Direct-dial entry of address 01 –159 on FlashScanO sys- mable option).
tems (IFC-640, IFC-3030), or 01 –99 on traditional sys- • LED latches steady to indicate alarm on command from
tems(IFC-400,IFG640,IFC-1010/2020,IFC-3030,or FG control panel.
2000). The M302MJ Interface Module is intended for use in intel-
ligent,addressable systems,where the individual address of
1415 0 � ADDRESS 0 � each module is selected using built-in rotary switches. This
13 ��2 � ��2 module allows intelligent panels to interface and monitor two-
0 �� wire conventional smoke detectors. It transmits the status
12 �3 LOOP 3
11 a � �:;�5 (normal, open,or alarm)of one full zone of conventional de-
10��6 5 9��,6 3 tectors back to the control panel. All two-wire detectors be-
8 7 $ � ing monitored must be UL compatible with the module. The
TENS ONES o M302MJ has a panel-controlled LED indicator and can be
� used to replace M502MJ modules in existing systems.
M302MJ Applications—Use the M302MJ to monitor
� � a zone of two-wire smoke detectors. The monitored circuit
O W p U may be wired as an NFPA Style B(Class B)or Style D(Class
� Q W ¢ A)Initiating Device Circuit.A 3.9 K ohm End-of-Line Resistor
� j � m (provided)terminates the end of the Style B or D (class B or
A)circuit(maximum IDC loop resistance is 25 ohms). Install
ELR across terminals 8 and 9 for Style D application.
M302MJ Operation—Each M302MJ uses one of 159
available module addresses on an SLC loop. It responds to
regular polls from the control panel and reports its type and
The M301MJ Mini Monitor Module can be installed in a the status (open/normal/short)of its Initiating Device Circuit
single-gang junction directly behind the monitored unit. Its (IDC).A flashing LED indicates that the module is in commu-
small size and light weight allow it to be installed without rigid nication with the control panel. The LED latches steady on
mounting.The M301 MJ is intended for use in intelligent,two- alarm (subject to current limitations on the loop).
wire systems where the individual address of each module M302MJ Speciflcations
is selected using rotary switches. It provides a two-wire initi-
ating device circuit for normally-open-contact fire alarm and Nominal operating voltage: 15 to 32 VDC.
security devices. The M301 MJ can be used to replace Maximum current draw: 5.1 mA (LED on).
M501MJ module in existing systems. Maximum operating current: 255 NA (LED flashing).
M301 MJ Applications— Use to monitor a single de- EOL resistance: 3.9K ohms.
vice or a zone of four-wire smoke detectors,manual fire alarm
pull stations,waterflow devices, or other normally-open dry- External supply voltage (between Terminals T3 and T4):
contact devices. May also be used to monitor normally-open DC voltage: 18 to 28 volts power limited. Ripple voltage:
supervisory devices with special supervisory indication at the 0.1 VRnns maximum. Current: 90 mA per module maximum.
control panel. Monitored circuit/device is wired as an NFPA Temperature range: 32°F to 120°F (0°C to 49°C).
Style B(Class B)Initiating Device Circuit.A47K ohm End-of- Humidity range: 10% to 93% noncondensing.
Line Resistor (provided) terminates the circuit. Dimensions: 4.5" (11.43 cm) high x 4" (10.16 cm) wide x
Page 2 of 6—JCI-6720•06/15/04
1.25" (3.175 cm) deep. Mounts to a 4" (10.16 cm)square x INSTALLATION
2.125" (5.398 cm) deep box. M300MJ, M300DJ, and M302MJ modules mount directly to a
M300DJ DUAL MONITOR MODULE standard 4" (10.16 cm)square, 2.125" (5.398 cm)deep, e�ec-
trical box.They may also be mounted to the SMB500 surface-
The M300DJ Dual Monitor Module is intended for use in mount box.Mounting hardware and installation instructions are
intelligent,two-wire systems.It provides two independent two- provided with each module. All wiring must conform to appli-
wire initiating device circuits(IDCs)at two separate,consecu- cable local codes, ordinances, and regulations. These mod-
tive addresses. It is capable of monitoring normally open ules are intended for power-limited wiring only.
contact fire alarm and supervisory devices;or either normally The M301MJ module is intended to be wired and mounted
open or normally closed security devices.The module has a �,yithout rigid connections inside a standard electrical box.All
single panel-controlled LED. NOTE.� The M300DJ provides „�riring must conform to applicable local codes, ordinances,
two Class 8 (Style Y) IDC circuits ONLY. Class A (Style Z) and regulations.
IDC circuits are NOT supported in any application.
M300DJ Specifications PRODUCT LINE INFORMATION
Normal operating voltage range: 15 to 32 VDC. M300MJ Monitor module.
Maximum current draw: 5.7 mA (LED on). M301MJ Monitor module, miniature.
Maximum operating current: 750 �A (LED flashing). M302MJ Monitor module, two-wire detectors
EOL resistance: 47K ohms. M300DJ Monitor module, dual, two independent Class
Maximum IDC wiring resistance: 1,500 ohms. B circuits.
Temperature range: 32° to 120°F (0° to 49°C). SMB500 Optional surface-mount backbox.
Humidity range: 10% to 93% (non-condensing). ARCHITECTS�/ENGINEERS�
Dimensions: 4.5" (11.43 cm) high x 4" (10.16 cm) wide x SPECIFICATIONS
2.125" (5.398 cm) deep. Specifications of these and all Johnson Controls products
M300DJ Automatic Addressing — The M300DJ are available from Johnson Controls.
automatically assigns itself to two addressable points, start-
ing with the original address. For example, if the M300DJ is
set to address "56", then it will automatically assign itself to
addresses "56" and "57". NOTE: "ones"addresses on the
M300DJ are 0, 2, 4, 6, or 8 only.Terminals 6 and 7 use the
first address,and terminals 8 and 9 use the second address.
OC14UT��l��
Avoid duplicating addresses on the system. �
�
�
G
O
�
�
� •
• ;; - I
O U � ���� �
�� i
E �� �
CAUTION 3 �
DE-ENER6IZEUNITPRIORTOSERVICING � � � �
m `a��; L �1
� /, ,F�" � �;
Face Plate for M300MJ, M302MJ, and M300DJ �`' � � _��° /�
I � � ��'./
� �
� I
� � 9��"��``2 a . �� �
� ����A� j�� MOUNTING DIAGRAMS � � �� � � �
3 � � � � ��
E � �� c-� ,% � for standard-sised 3 ���
� (� moda/es � �� ��
� �� ��
il� � � �
. �
JCI-6720•06/15/04 —Page 3 of 6
WIRING DIAGRAMS
The following wiring diagrams are included:
1) M300DJ, typical dual two-wire Style B initiating device circuit configuration.
2) M301MJ, typical two-wire Style B initiating device circuit configuration.
3) M300MJ, typical two-wire initiating circuit configuration, NFPA Style B.
4) M300MJ, typical four-wire fault-tolerant initiating circuit configuration, NFPA Style D.
5) M300MJ, typical two-wire initiating circuit configuration for security systems (with alarm
versus short capability).
6) M302MJ, interface two-wire conventional detectors, NFPA Style B.
7) M302MJ, interface two-wire conventional detectors, NFPA Style D.
8) M300RJ, relay control module used to disconnect a power supply.
� , � � �
Fig. 1 M300DJ: Typical dual two-wire Style 8
initiating device circuit configuration.
Two Initiating Device Circuits �_�
� (L & H) TO Next �+� �J�J (—) FROM Panel
each power-limitedto Device orPrevious
230 NA max. @ 12 VDC max. MONITOR 00 (+) Device
47KEOL �� MODULE � �
Resistor T H — Communication Line
ELR-47K � 9 O �� 32 VDC maximum.
(—) Twisted-pair is
� recommended.
� 8 1 � �+�
� 7 TENS 2�
47K EOL � 6 � 3 � •All wiring shown is supervised
Resistor � — I = � 5 ONES 4� and power limited.
ELR-47K � ILOOP ADDRESS
o • Connect modules to Listed compatible
� � � � � � control panels only.
•ANY NUMBER of UL Listed contact closure devices may be used. sszsW��,.Wmf
• DO NOT MIX fire alarm initiating, supervisory,or security devices on the same circuit.
• Install contact closure devices per manufacturer's installation instructions.
(+) � � TO
(—} ��' ►NEXT
DEVIGE
UL LISTED BLACK► �RED
Compatible (—} (+} M301 MJ
Panel�l 4s s��ioi 45��8 9
3����12 3((�
2�,�j 13 2\
10 1514 1� �+��—�
VIOLET► �YELLOW
� , �
47K EOL INCLUDED
Fig. 2 M301 MJ: Typical two-wire Style 8
initiating device circuit configuration. �
j6720w2.wmf
Page 4 of 6—JCI-6720•06/15/04
, , � �
• Connect modules to listed compatible Johnson Controls control panels only.
• All wiring shown is supervised and power limited.
• Install contact closure devices per manufacturers' installation instructions.
• Any number of UL-listed contact closure devices may be used.
• DO NOT MIX fire alarm initiating, supervisory, or security devices on the same circuit.
� Fig. 3 M300MJ: Typical two-wire initiating device circuit configuration, NFPA Style B.
TO Next �—�
Device (+} 000 (-) FROM Panel
00 �+� or Previous
MONITOR —t Device
Initiating Device Circuit(IDC) � MODULE � �
NFPA Style B, power limited: Communication Line
230�A max.@ 12 VDC max. � 9 � p� 32 VDC maximum.
(-) Twisted-pair is
� $ � � � (+) recommended.
47K EOL � 7 r=_r,s 2 �
ELR 47K ❑ 5 �' 4� �������� Communication Loss
c.es
LOOP nooRess (optional connection for panels
�� 1 � � �- which support this feature)
� � � C� FUTURE FEATURE
6720wir2.wmf
� Fig. 4 M300MJ: Typical four-wire fault-tolerant initiating circuit configuration, NFPA Style D.
TO Next t��
Device � 000 (-) FROM Panel
��� �+� or Previous
MO N ITOR Device
� MODULE � �
Communication Line
� 9 O �� 32 VDC maximum.
(-) Twisted-pair is
� 8 1 � �+�
recommended
EOL Resistor � 7 TENS 2�
is internal at � �6 � 3� °
terminals 8&9 ❑ 5 � q� .....:�� Communication Loss
���ooP °N`s nooaess (optional connection for panels
° n which support this feature)
� � � C� FUTURE FEATURE
6720wir3.wmf
� Fig. 5 M300MJ: Typical two-wire initiating circuit configuration for security systems
(with alarm versus short capability).
TO Next �-}
Initiating Device Circuit(IDC) Device (+) OJOOO � o�Prevous�
NFPA Style B, power limited: MONITOR ��� �� Device
230 �A max. @ 12 VDC max. �� MODULE
� Communication Line
14K Series Resistor� � g � p� 32 VDC maximum.
�� (-) Twisted-pair is
� 8 1 � ��,�
recommended.
47K EOL � 7-eNS 2 �
ELR 47K T ❑ 5 "� 4� ����� Communication Loss
�ooP °"�s AooRess (optional connection for panels
� � � f� which support this feature)
� �' C� FUTURE FEATURE
6720wir4.wmf
JCI-6720•06/15/04 —Page 5 of 6
• Connect modules to listed compatible control panels only.
• Terminal wiring must be power limited.
• DO NOT MIX fire alarm initiating, supervisory, or security devices on the same circuit. � � '
• DO NOT LOOP wire under terminals. Break wire run to provide supervision of connections.
• Detectors must be UL Listed compatible with module. ,
• Install detectors per manufacturers' installation instructions.
• Power to the interface module must be externally switched to reset the detectors. � �
An M300RJ relay control module can be used to switch power from a standard power supply; see Fig. 7 below.
� Fig. 6 M302MJ: Interface two-wire conventional detectors, NFPA Style 8.
TO Next _��+��GO000 O (+� FROM Panel
Device �—�� or Previous
INTERFACE Device
� MODULE � ��Communication Line
32 VDC maximum.
� g � Q� Twisted-pair is
� recommended.
(–)
3.9K EOL � 8 �-=NS 2� �+� �_� Listed Battery Backup
Resistor � 6 � 3� (+� switched DC
(included) ❑ 5 „C5 4 � power supply.
A2143-10 ���� �� �ooa n�oRFSs
+ + � � � ° 0 � � Optional Branch Circuit
– TO Next Interface Module
s�zow��s.wmr Module supervises supply
voltage and detector loop.
� Fig. 7 M302MJ: Interface two-wire conventional detectors, NFPA Style D.
TO Next �—} � FROM Panel
Device (+) OOOOOG O (+) or Previous
Device
INTERFACE
MODULE C ��Communication Line
� � o � 32 VDC maximum.
� Twisted-pair is
� g � �� recommended.
3.9K EOL Resistor � g � � � �+�
(included) required � 7 �EN, 2 �
at terminals 8&9 � g „ 3 � �–� Listed Battery Backup
A2143-10 � 5 � q� (+) � switched DC
" � �ooa o�rs n���FSS power supply.
� ��� � � � ° � � � Optional Branch Circuit
`� TO Next Interface Module
� �`�� s�zow,�s.wmr Module supervises supply
voltage and detector loop.
� Fig. 8 M300RJ: Relay control module used to disconnect a power supply.
TO Next ( > �—� FROM Panel
Device �+� ����00 (+) or Previous
RELAY Device
DC POWER CONTROL
SUPPLY �+� � MODULE C�, R
o L� �
Listed for Fire (—) � Communication Line
ProteCtion with +� 9 0❑ 0 32 VDC maximum.
Battery Backup +� 8 � �+ – Twisted-pair is
� �–{ 2 � ��� recommended.
�—� � 6 3 �
�'}� � 5��-4 +)
LOOP ADDRESS
� � � � �
6720wir7.wmf
Page 6 of 6—JCI-6720•06/15/04