The URL can be used to link to this page

Home My WebLink AboutF11-0027TOWN OF VAIL FIRE DEPARTMENT VAIL FIRE DEPARTMENT 75 S. FRONTAGE ROAD VAIL, CO 81657 970 - 479 -2135 NOTE: THIS PERMIT MUST BE POSTED ON JOBSITE AT ALL TIMES SPRINKLER PERMIT Permit #: F1 1 -0027 Job Address: 1452 BUFFEHR CREEK RD VAIL Status ...: ISSUED Location.....: Applied..: 05/20/2011 Parcel No...: 210312102028 Issued . .: 05/31/2011 Project No Expires. .: OWNER DBCAJT LLC 05/20/2011 $0.00 Payments ------------------- > 2187 ATLANTIC ST .00 STAMFORD BALANCE DUE --------- > $0.00 CO 06902 ************************************************************************************************************** * * * * * * * * * * * * * * * * * * * CONTRACTOR ALL STATE FIRE PROTECTION, I 05/20/2011 Phone: 303 - 288 -3901 10045 E 76TH AVE, #12 Item: 05600 FIRE COMMERCE CITY CO 80022 05/25/2011 mvaughan Action: AP License: 370 -S APPLICANT DBCAJT LLC 05/20/2011 2187 ATLANTIC ST STAMFORD CO 06902 Desciption: ADD /RELOCATE 7 RESIDENTIAL SPRINKLER HEADS ON THE LOWER LEVEL. Valuation: $1,200.00 ************************************* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * ** FEE SUMMARY ************************** * * * * * * * * * * * * * * * * * * * * * * * * * * * * * ** Mechanical --- > $0.00 Restuarant Plan Review - -> $0.00 Total Calculated Fees --- > $483.00 Plan Check --- > $432.00 DRB Fee --------------------- > $0.00 Additional Fees------ - - - - -> $0.00 Investigation -> $0.00 TOTAL FEES--------- - - - - -> $483.00 Total Permit Fee ---------- > $483.00 Will Call - - - - -> $0.00 Payments ------------------- > $483 .00 BALANCE DUE --------- > $0.00 ************************************************************************************************************** * * * * * * * * * * * * * * * * * * * * * * * * * * * * * ** Item: 05100 BUILDING DEPARTMENT Item: 05600 FIRE DEPARTMENT 05/25/2011 mvaughan Action: AP CONDITION OF APPROVAL Cond: 12 (BLDG.): FIELD INSPECTIONS ARE REQUIRED TO CHECK FOR CODE COMPLIANCE. Cond: 53 (FIRE 2007) Monitored fire sprinkler system required and shall comply with NFPA 13 (2007) and VFES Standards. ************************************************************************************************************** * * * * * * * * * * * * * * * * * * * * * * * * * * * * * ** DECLARATIONS I hereby acknowledge that I have read this application, filled out in full the information required, completed an accurate plot plan, and state that all the information as required is correct. I agree to comply with the information and plot plan, to comply with all Town ordinances and state laws, and to build this structure according to the towns zoning and subdivision codes, design review approved, International Building and Residential Codes and other ordinances of the Town applicable thereto. REQUESTS FOR INSPECTION SHALL BE MADE TWENTY -FOUR HOURS IN ADVANCE BY TELEPHONE AT 970 - 479 -2252 FROM 8:00 AM - 5 PM. TOWN OF VAIL, COLORADO Statement Statement Number: R110000574 Amount: $483.00 05/31/201112:21 PM Payment Method: Check Init: LC Notation: #29619 /ALL STATE FIRE PROTECTION ----------------------------------------------------------------------------- Permit No: Fll -0027 Type: SPRINKLER PERMIT Parcel No: 2103 -121- 0202 -8 Site Address: 1452 BUFFEHR CREEK RD VAIL Location: Total Fees: $483.00 This Payment: $483.00 Total ALL Pmts: $483.00 Balance: $0.00 ACCOUNT ITEM LIST: Account Code Description Current Pmts -------------- - - - - -- ------------------------ - - - - -- ------ - - - - -- BP 00100003111100 SPRINKLER PERMIT FEES 51.00 PF 00100003112300 PLAN CHECK FEES 432.00 Department of Community Development .75 South Frpntage �oad Vail,: orado_8147 :TAT: 970479.2128, . `.Fax: 970- 479 - 2452 f WAp:';www.Vallgov.corn eyelt rent Review Coordinator FIRE SPRINKLER PERMIT Commercial & Residential Fire Alarm shop drawings are required at the time of application submittal and must include the following information: 1. A Colorado Registered Engineer's stamp or N.I,C.E.T level III (min) stamp 2. Equipment cut sheets of materials 3. Hydraulic calculations 4. A State of Colorado contractor registration number 5. Plans must be submitted by a Registered Fire Protection Contractor Project Street Address: 1452 Buffehr Creek Rd (Number) (Street) (Suite #) Building /Complex Name: Brownstein Re Contractor Information: Company: All -State Fire Protection, Inc. Company Address: 6045 E. 76th Ave #12 City: Commerce City State: CO Contact Name: Michael Krzastek Zip: 80022 Contact Phone: 303 - 288 -3901 E -Mail mikek @allstatefireprotection.com Town of Vail Contractor Registration No.: 370 -S X VA',wa Contractor Signatffe (required) Property Information Parcel # 2103- 121 -02 -028 (For parcel #, contact Eagle County Assessors Office at 970 - 328 -8640 or visit ewwv.eaglecounty.us /patie) Tenant Name: Brownstein Residence Owner Name: Complete Valuation for Fire Sprinkler Permit: Fire Sprinkler $: $1,200.00 (use additional sheet if necessary) Detailed Location of Work Lower Level i Does a Monitored Fire Alarm Exist? Yes No ( ) ^! Does a Sprinkler System Exist? Yes(, No( ) Work Class: New ( ) Addition ( ) Remodel ( .,) Repair ( ) Retro-Fit ( ) Other ( ) Type of Building: Single - Family Duplex ( ) Multi - Family ( ) Commercial ( ) Restaurant ( ) Other ( ) Date Received: MAY 1 1U11 V Office Use: Project #: Building Permit #: 0o ., Sprinkler Permit #: — 0019, r Lot #: Block # Subdivision: Detailed Description of Work- Add/Relocate 7 Residential Sprinkler Heads 01- Feb-10 tqco Fire Suppression & Building Products Technical Services 800 - 381 -9312 1 +1- 401 - 781 -8220 www.tyco - fire.com Series LFII Residential Sprinklers Flat -Plate Concealed Pendent 4.9 K- Factor ,a rapid response° HOME FIRE SPRINKLER SYSTEM General Description The TYCO RAPID RESPONSE Series LFII Residential Flat -Plate Concealed Pendent Sprinklers (TY2524) are decora- tive, fast response, fusible solder sprin- klers designed for use in residential oc- cupancies such as homes, apartments, dormitories, and hotels. The Cover Plate /Retainer Assembly con- ceals the sprinkler operating compo- nents above the ceiling. The flat profile of the Cover Plate provides the optimum aesthetically appealing sprinkler design. Additionally, the concealed design of the Series LFII Residential Flat -Plate Con- cealed Pendent Sprinklers provides 1/2 inch (12,8 mm) vertical adjustment. This adjustment provides a measure of flex- ibility when cutting fixed pipe drops. The Series LFII Residential Flat -Plate Concealed Pendent Sprinklers are in- tended for use in the following systems: • per NFPA 13D, wet pipe residential sprinkler systems for one- and two - family dwellings and mobile homes; • per NFPA 13R, wet pipe residential sprinkler systems for residential oc- cupancies up to and including four stories in height; and • per NFPA 13, wet pipe sprinkler sys- tems for the residential portions of any occupancy. IMPORTANT Always refer to Technical Data Sheet TFP700 for the `INSTALLER WARNING' that provides cautions with respect to handling and instal- lation of sprinkler systems and com- ponents. Improper handling and in- stallation can permanently damage a sprinkler system or its components and cause the sprinkler to fail to operate in a fire situation or cause it to operate prematurely. The Series LFII Residential Flat -Plate Concealed Pendent Sprinkler has a 4.9 (60,5) K- factor that provides the required residential flow rates at reduced pres- sures, enabling smaller pipe sizes and water supply requirements. This sprinkler has been designed with heat sensitivity and water distribution characteristics proven to help in the con- trol of residential fires and to improve the chance for occupants to escape or be evacuated. The Series LFII Residential Flat -Plate Concealed Pendent Sprinklers are shipped with a Disposable Protective Cap. The Protective Cap protects the sprinkler during ceiling installation or finish. After ceiling installation is com- plete, the Protective Cap is removed and the Cover Plate /Retainer Assem- bly is installed. Removing the Protec- tive Cap is required for proper sprinkler performance. '® The Series LFII Residential Flat -Plate Concealed Pendent Sprinklers (TY2524) described herein must be installed and maintained in compliance with this doc- ument and with the applicable standards of the National Fire Protection Associa- tion, in addition to the standards of any authorities having jurisdiction. Failure to do so may impair the performance of these devices. Owners are responsible for maintaining their fire protection system and devices in proper operating condition. The in- stalling contractor or sprinkler manu- facturer should be contacted with any questions. Technical Data Approvals UL and C -UL Listed NSF -61 Certified The Series LFII Residential Flat -Plate Concealed Pendent Sprinklers are only listed with the Series LFII Concealed Cover Plates having a factory- applied finish. Maximum Working Pressure 175 psi (12,1 bar) Discharge Coefficient K =4.9 GPM /psi (70,6 LPM /bar Temperature Rating Sprinkler: 160 °F (71 °C) Cover Plate: 139 °F (59 °C) Model /Sprinkler Identification Number (SIN) TY2524 Vertical Adjustment 1/2 inch (12,7 mm) Finishes Refer to the Ordering Procedure section. Physical Characteristics • Cover Plate /Retainer Assembly: Cover Plate ............. Copper Ejection Spring .... Stainless Steel Retainer ................ Brass Page 1 of 6 OCTOBER 2010 TFP443 TFP443 Page 2 of 6 • Sprinkler /Support Cup Assembly: Body ................... Brass Horizontal Ceiling Minimum Flow and Residual Pressure Sloped Ceiling Minimum FlowN and Residual Pressure Sloped Ceiling Minimum Flow" and Residual Pressure Brass Sealing Assembly .......Beryllium Maximum Covene Area i• Maximum Spacing (Maximum 2 -inch rise for 12 -inch run) (Greater than 2 -inch rise up to maximum 4 -inch rise for 12 -inch run) (Greater than 4 -inch rise up to maximum 8 -inch rise for 12 -inch run) Bronze 160OF(71 0 C) Sprinkler 160 °F(71 °C) Sprinkler 160 °F(71 °C) Sprinkler Bronze Guide Pin Housing........ Bronze Guide Pins ............. Bronze 12'x 12' (3,7 m x 3,7 m) 12' (3,7 m) 13 GPM (49,2 LPM) 7.0 psi (0,48 bar) 17 GPM (64,3 LPM) 12.0 psi (0,83 bar) 17 GPM (64,3 LPM) 12.0 psi (0,83 bar) 14'x 14' 14' 13 GPM (49,2 LPM) 17 GPM (64,3 LPM) 17 GPM (64,3 LPM) 18 x 1 (5,5 m x 5,5 m) 1 (5,5 m) 17 4, 12.0 psi (0,83 bar) 2 L 20.2 psi (1,39 bar) 20.2 psi (1,39 bar) 20'x 20' (6,1 m x 6,1 m) 20' (6,1 m) 20 GPM (75,7 LPM) 16.7 psi (1,15 bar) 24 GPM (90,8 LPM) 24.0 psi (1,65 bar) 24 GPM (90,8 LPM) 24.0 psi (1,65 bar) (a) For coverage area dimensions less than or between those indicated, use the minimum required flow for the next highest coverage area for which Hydraulic Design section under the Design Criteria are stated. (b) The Minimum Flow requirement is based on minimum flow in GPM (LPM) from each sprinkler. The associated residual pressures are calculated using the nominal K- factor. Refer to "Hydraulic Design" in the Design Criteria section for details. TABLE A SERIES LFII RESIDENTIAL FLAT -PLATE CONCEALED PENDENT SPRINKLER (TY2524) NFPA 13D AND NFPA 13R HYDRAULIC DESIGN CRITERIA WET PIPE SYSTEMS • Sprinkler /Support Cup Assembly: Body ................... Brass Cap ................... Bronze Saddle .................. Brass Sealing Assembly .......Beryllium 16' (4,9 m) Nickel w/ Teflon' Soldered Link Halves ...... Nickel Lever .................. Bronze Compression Screw ....... Brass Deflector ............... Bronze Guide Pin Housing........ Bronze Guide Pins ............. Bronze Support Cup .............. Steel Operation When exposed to heat from a fire, the Cover Plate, which is normally soldered to the Retainer at three points, falls away to expose the Sprinkler /Support Cup As- sembly. At this point, the Deflector, sup- ported by the Guide Pins, drops down to its operated position. The Solder Link Element of the Sprinkler/ Support Cup Assembly is comprised of two link halves that are soldered togeth- er with a thin layer of solder. When the rated temperature is reached, the sol- der melts and the two link halves sepa- rate, allowing the sprinkler to activate and flow water. 1 Registered trademark of Dupont Design Criteria The TYCO RAPID RESPONSE Series LFII Residential Flat -Plate Concealed Pendent Sprinklers (TY2524) are UL and C -UL Listed for installation in ac- cordance with the following criteria. NOTICE When conditions exist that are outside the scope of the provided criteria, re- fer to the Residential Sprinkler Design Guide TFP490 for the manufacturer's recommendations that maybe accept- able to the Authority Having Jurisdiction, The Series LF/l Residential Flat -Plate Concealed Pendent Sprinklers must not be used in applications where the air pressure above the ceiling is greater than that below. Down drafts through the Support Cup can delay sprinkler op- eration in a fire situation. System Type Only wet pipe systems maybe utilized. Hydraulic Design Table A provides the minimum required sprinkler flow rate for systems designed to NFPA 13D or NFPA 13R as a function of temperature rating and the maximum allowable coverage areas. The sprinkler flow rate is the minimum required dis- charge from each of the total number of "design sprinklers" as specified in NFPA 13D or NFPA 13R. For systems designed to NFPA 13, the number of design sprinklers is to be the four most hydraulically demanding sprinklers. The minimum required dis- charge from each of the four sprinklers is to be the greater of the following: •flow rates given in Table A for NFPA 13D and 13R as a function of tem- perature rating and the maximum al- lowable coverage area •minimum discharge of 0.1 GPM/ sq. ft. over the "design area" com- prised of the four most hydraulically demanding sprinklers for actual cov- erage areas protected by the four sprinklers Obstruction To Water Distribution Locate sprinklers in accordance with the obstruction rules of NFPA for residential sprinklers as well as obstruction criteria described within TYCO technical data sheet TFP490. Operational Sensitivity Install sprinklers relative to the ceiling mounting surface as shown in Figure 3. Sprinkler Spacing The minimum spacing between sprin- klers is 8 feet (2,4 m). The maximum spacing between sprin- klers cannot exceed the length of the coverage area (Table A) being hydrau- lically calculated; for example, a maxi- mum of 12 feet fora 12 ft. x 12 ft. cov- erage area or 20 feet fora 20 ft. x 20 ft. coverage area. 16' x i6' (4,9 m x 4,9 m) 16' (4,9 m) 13 GPM (49,2 LPM) 7.0 psi (0,48 bar) 17 GPM (64,3 LPM) 12.0 psi (0,83 bar) 17 GPM (64,3 LPM) 12.0 psi (0,83 bar) Design Criteria The TYCO RAPID RESPONSE Series LFII Residential Flat -Plate Concealed Pendent Sprinklers (TY2524) are UL and C -UL Listed for installation in ac- cordance with the following criteria. NOTICE When conditions exist that are outside the scope of the provided criteria, re- fer to the Residential Sprinkler Design Guide TFP490 for the manufacturer's recommendations that maybe accept- able to the Authority Having Jurisdiction, The Series LF/l Residential Flat -Plate Concealed Pendent Sprinklers must not be used in applications where the air pressure above the ceiling is greater than that below. Down drafts through the Support Cup can delay sprinkler op- eration in a fire situation. System Type Only wet pipe systems maybe utilized. Hydraulic Design Table A provides the minimum required sprinkler flow rate for systems designed to NFPA 13D or NFPA 13R as a function of temperature rating and the maximum allowable coverage areas. The sprinkler flow rate is the minimum required dis- charge from each of the total number of "design sprinklers" as specified in NFPA 13D or NFPA 13R. For systems designed to NFPA 13, the number of design sprinklers is to be the four most hydraulically demanding sprinklers. The minimum required dis- charge from each of the four sprinklers is to be the greater of the following: •flow rates given in Table A for NFPA 13D and 13R as a function of tem- perature rating and the maximum al- lowable coverage area •minimum discharge of 0.1 GPM/ sq. ft. over the "design area" com- prised of the four most hydraulically demanding sprinklers for actual cov- erage areas protected by the four sprinklers Obstruction To Water Distribution Locate sprinklers in accordance with the obstruction rules of NFPA for residential sprinklers as well as obstruction criteria described within TYCO technical data sheet TFP490. Operational Sensitivity Install sprinklers relative to the ceiling mounting surface as shown in Figure 3. Sprinkler Spacing The minimum spacing between sprin- klers is 8 feet (2,4 m). The maximum spacing between sprin- klers cannot exceed the length of the coverage area (Table A) being hydrau- lically calculated; for example, a maxi- mum of 12 feet fora 12 ft. x 12 ft. cov- erage area or 20 feet fora 20 ft. x 20 ft. coverage area. TFP443 Page 3 of 6 BODY SEALING ( / NPR ASSEMBLY CAP SPRINKLER SADDLE 1_i ` • ``` , I AREA SUPPORT COMPRESSION CUP WITH SCREW ROLL FORMED THREADS LEVER GUIDE PIN SOLDER LINK ELEMENT GUIDE PIN HOUSING DEFLECTOR " ' -- - - - - -` " r �- , (OPERATED DEFLECTOR --- --- -s POSITION) SPRINKLER /SUPPORT CUP ASSEMBLY THREAD INTO RETAINER SUPPORT CUP WITH THREAD UNTIL MOUNTING DIMPLES SURFACE IS CD O FLUSH WITH EJECTION CEILING SPRING SOLDER J COVER PLATE /RETAINER COVER TAB ASSEMBLY PLATE FIGURE 1 FLAT -PLATE CONCEALED PENDENT SPRINKLER (TY2524) ASSEMBLY WRENCH RECESS PUSH WRENCH IN TO ENSURE ENGAGEMENT WITH SPRINKLER WRENCHING AREA FIGURE 2 W -TYPE 18 SPRINKLER WRENCH 2 -1/2" DIA. (63.5 mm) SPRINKLER - 1/2" (12,7 mm) FACE OF SUPPORT CUP THREADED SPRINKLER ASSEMBLY ADJUSTMENT FITTING OPERATE SPRINKLE 1- 7/8 "t1 /8" COVER ( -7/8 mm PLATE 1/8" GAP f3,2 mm) RETAINEF r (3,2 mm) F MOUNTING 7/8" (22,2 n 3/16" SURFACE 1 -1/8 (28 (4,8 mm) DISPOSABLE t.I.— ..... ) TIP PROTECTIVE CAP FIGURE 3 PROTECTIVE CAP AND ACTIVATED DEFLECTOR INSTALLATION DIMENSIONS DEFLECTOR IN OPERATED POSITION TFP443 Page 4 of 6 Installation The TYCO RAPID RESPONSE Series LFII Residential Flat -Plate Concealed Pendent Sprinklers must be installed in accordance with the following instructions. NOTICE Damage to the Solder Link Element dur- ing installation can be avoided by han- dling the sprinkler by the Support Cup only; that is, do not apply pressure to the Solder Link Element (Figure 1). Obtain a leak -tight 112 inch NPT sprinkler joint by applying a minimum -to -maxi- mum torque of 7 to 14 ft. -lbs. (9,5 to 19,0 Nm). Higher levels of torque can distort the sprinkler inlet with consequent leak- age or impairment of the sprinkler. Do not attempt to compensate for in- sufficient adjustment in the Cover Plate/ Retainer Assembly by under- or over - tightening the sprinkler. Re- adjust the position of the sprinkler fitting to suit. 1. Install pendent sprinklers in the pendent position, with the center- line of the sprinkler perpendicular to the mounting surface. 2. Remove the Protective Cap. 3. With pipe- thread sealant applied to the pipe threads, and using the W -Type 18 Wrench shown in Figure 2, install and tighten the Sprinkler/ Support Cup Assembly into the fit- ting. The W Type 18 Wrench ac- cepts a 1/2 inch ratchet drive. 4. Replace the Protective Cap by pushing it upwards until it bottoms out against the Support Cup. The Protective Cap helps prevent dam- age to the Deflector and Guide Pins during ceiling installation and/ or during application of the finish coating of the ceiling. NOTICE As long as the protective Cap re- mains in place, the system is con- sidered "Out Of Service ". After the ceiling has been com- pleted with the 2 -1/2 inch (63 mm) diameter clearance hole and in preparation for installing the Cover Plate /Retainer Assembly, remove and discard the Protective Cap, and verify that the Deflector moves up and down freely. If the Sprinkler has been damaged and the Deflector does not move up and down freely, replace the entire Sprinkler assembly. Do not attempt to modify or repair a damaged sprinkler. Screw on the Cover Plate /Retainer Assembly until its flange contacts the ceiling. Do not continue to screw on the Cover Plate /Retainer Assembly such that it lifts a ceiling panel out of its normal position. If the Cover Plate /Retainer Assembly cannot be engaged with the Mounting Cup or the Cover Plate /Retainer As- sembly cannot be engaged sufficiently to contact the ceiling, the Sprinkler Fitting must be repositioned. Care and Maintenance The TYCO RAPID RESPONSE Series LFII Residential Flat -Plate Concealed Pendent Sprinkler (TY2524) must be maintained and serviced in accordance with the following instructions. Before closing a fire protection system main control valve for maintenance work on the fire protection system that it con- trols, obtain permission to shut down the affected fire protection system from the proper authorities and notify all person- nel who may be affected by this action. When properly installed, there is a nomi- nal 1/8 inch (3,2 mm) air gap between the lip of the Cover Plate and the ceil- ing, as shown in Figure 3. This air gap is necessary for proper operation of the sprinkler by allowing heat flow from a fire to pass below and above the Cover Plate to help assure appropriate release of the Cover Plate in a fire situation. If the ceiling needs repainting after sprinkler installation, exercise care to ensure that the new paint does NOT seal off any of the air gap. Failure to do so may impair sprinkler operation. Absence of a Cover Plate can delay the sprinkler operation in a fire situation. Do not pull the Cover Plate relative to the Enclosure. Separation may result. Exercise care to avoid damage to sprin- klers before, during, and after installa- tion. Never paint, plate, coat, or other- wise alter automatic sprinklers after they leave the factory. Never repaint factory - painted Cover Plates. When necessary, replace cover plates with factory - painted units. Non - factory applied paint can adversely de- lay or prevent sprinkler operation in the event of a fire. Replace sprinklers that: were damaged by dropping, striking, wrench twisting, wrench slippage, or the like. • were modified or over - heated • are leaking or exhibiting visible signs of corrosion. Responsibility lies with owners for the inspection, testing, and maintenance of their fire protection system and devices in compliance with this document, as well as with the applicable standards of the National Fire Protection Association (for example, NFPA 25), in addition to the standards of any other authorities having jurisdiction. Contact the install- ing contractor or sprinkler manufacturer regarding any questions. Automatic sprinkler systems are rec- ommended to be inspected, tested, and maintained by a qualified Inspec- tion Service in accordance with local requirements and /or national codes. TFP443 Page 5 of 6 Limited Warranty Products manufactured by Tyco Fire Suppression & Building Products ( TFSBP) are warranted solely to the orig- inal Buyer for ten (10) years against de- fects in material and workmanship when paid for and properly installed and main- tained under normal use and service. This warranty will expire ten (10) years from date of shipment by TFSBP. No warranty is given for products or com- ponents manufactured by companies not affiliated by ownership with TFSBP or for products and components which have been subject to misuse, improper installation, corrosion, or which have not been installed, maintained, modified or repaired in accordance with applicable Standards of the National Fire Protection Association, and /or the standards of any other Authorities Having Jurisdiction. Materials found by TFSBP to be defec- tive shall be either repaired or replaced, at TFSBP's sole option. TFSBP neither assumes, nor authorizes any person to assume for it, any other obligation in connection with the sale of products or parts of products. TFSBP shall not be responsible for sprinkler system design errors or inaccurate or incomplete in- formation supplied by Buyer or Buyer's representatives. In no event shall TFSBP be liable, in con- tract, tort, strict liability or under any oth- er legal theory, for incidental, indirect, special or consequential damages, in- cluding but not limited to labor charg- es, regardless of whether TFSBP was informed about the possibility of such damages, and in no event shall TFSBP's liability exceed an amount equal to the sales price. The foregoing warranty is made in lieu of any and all other warranties, express or implied. including warranties of mer- chantability and fitness for a particular purpose. This limited warranty sets forth the ex- clusive remedy for claims based on fail- ure of or defect in products, materials or components, whether the claim is made in contract, tort, strict liability or any oth- er legal theory. This warranty will apply to the full extent permitted by law. The invalidity, in whole or part, of any portion of this warranty will not affect the remainder. Ordering Procedure Contact your local distributor for avail- ability. When placing an order, indicate the full product description and Part Number (P /N). Sprinkler /Support Cup Assembly Specify: Series LFII Residential Flat - Plate Concealed Pendent Sprinkler (TY2524), K =4.9, without Cover Plate/ Retainer Assembly, P/N 51 -114 -1 -160. Cover Plate /Retainer Assembly Specify: Cover Plate /Retainer Assem- bly with finish (below) for the Series LFII Residential Flat -Plate Concealed Pendent Sprinkler (TY2524), K =4.9, P/N (below): Chrome .................. P/N 56- 201 -9 -135 Custom ...................P /N 56- 201 -X -135 Off White ................ P/N 56- 201 -0 -135 Pure White* (RAL 9010) ................ P/N 56- 201 -3 -135 Signal White" (RAL 9003) ............... P/N 56- 201 -4 -135 Standard White (Grey White) (RAL9002) ................ P/N 56- 201 -5 -135 Eastern Hemisphere sales only. Previously known as Bright White. Note: All Custom Cover Plates are painted using Sherwin Williams Interior Latex Paint. Contact TYCO Customer Service with any questions related to custom orders. Sprinkler Wrench Specify W -Type 18 Sprinkler Wrench, P/N 56- 000 -1 -265. TFP443 Page 6 of 6 Copyright 0 2010 Tyco Fire Suppression & Building Products. All rights reserved.