HomeMy WebLinkAboutB12-0390 _ _
� � � �'1�
� �
09-01-2015 Inspection Request Reporting Page 1
4:03 qm VaiI,S;O - Citv Of
Requested Inspect Date: Wednesday,September 02,2015
Site Address: 1151 VAIL VIEW DR VAIL
UNIT A
A/P/D Information
Activity: B12-0390 Type: COMBO Sub Type: ADUP Status: EXPIRED
Const Type: Occupancy: Use: Insp Area:
Owner: BRAUN,DANIEL J.
Applicant: SNO-AWAY INC Phone: 970-379-4286
Contractor: SNO-AWAY INC Phone: 970-379-4286
Description: DECKANG.RAIUNG TO M�TGH WITH�E)CCTEPTSdN OFFF�ICKET SPACINGNGS,FLAT ROOF AND
Notice: EXPIRED LETTER-JMONDRAGON
Comment: EMAILED CONTRACTOR PERMIT EXPIRES 01/12/15-JMONDRAGON
Comment: SCANNED APPLICATION. ROUTED TO E-4 AND WARREN.-JMONDRAGON
Comment: BUILDING DEPT APPROVED PLANNING PENDING PLANS IN E-4-JMONDRAGON
Re uested s "ection s
Rem: 542 PLAN-FINAL Requested Time: 08:00 AM
Requestor: SNO-AWAY INC Phone: 970-379-4286
Comments: 379-4286
� ned To: GRUTHER Entered By: JMONDRAGON K
�
ction: ' e Exp:
Item: 90 BLDG-Final Requested Time: 04:00 PM
Requestor: SNO-AWAY INC Phone: 970-379-4286
Comments: 379-4286
Assigned To: Entered By: JMONDRAGON K
Action: Time Exp:
Item: 190 E EC-F'n I Requested Time: 03:30 PM
Requestor: S - Y Phone: 970-379-4286
Comments: 3 9
Assigned To: Entered By: JMONDRAGON K
Action: Time Exp:
Inspection Historv � �� � ���
Item: 120 ELEC-Rough
Item: 30 BLDG-Framing ""Approved'"
09/20/12 Inspector: mdenney Action: AP APPROVED
Comment: front porch/area above garage.
11/29/12 Inspector: sg remmer Action: PI PARTIAL INSPECTION
Comment: west upper wall
Item: 50 BLDG-Insulation
Item: 60 BLDG-Sheetrock Nail
item: 70 BLDG-Misc.
Item: 190 ELEC-Final
Item: 542 PLAN-FINAL
Item: 90 BLDG-Final
REPT131 Run Id: 15011
TOWN OF VAIL'
Department of Community Development
75 South Frontage Road
Vail, CO 81657
Tel: 970-479-2128
www.vailgov.com
Development Review Coordinator
BUILDING PERMIT APPLICATION
(Separate applications are required for alarm & sprinkler)
Project Street Address:
/�7� Cr�soLq�2 .t�- No,� 02. �
(Number) (Street)
Building/Complex Name:
Contractor Information
(Suite #)
Project #: P I�J �� - � y`"'� ;.�
DRB #: ����� �p
Building Permit#: (�� � �39 �
Lot #: Block # Subdivision:
Business Name:
S�JO-I�W �`/i.�1�L, �
Work Class
Business Address: �O �(y 0 %
New (Oj Addition (�j Alteration �
City 13�5/4(, f State: CO Zip: ��(ool� Type of Buildin :
Single-Family �j Duplex �j Multi-Family �j
Contact Name: /2o SS E�o,,, g,� W 5 k,,'
Commercial (� Other �j
Contact Phone: �y7a � 3 % 5 - 'l�ot8 �a
Contact E-Mail: /'o S 5�a,n 6�^o ws K� c� CO►+�►c�f ��-� Work Type: Interior o Exterior � Both �
I hereby acknowledge that I have read this application, filled out
in futl the information required, completed an accurate plot plan,
and state that all the information as required is correct. I agree to
comply with the information and ptot plan, to comply with all Town
ordinances and state laws, and to build this structure according to
the town's zoning and subdivision codes, design review ap-
proved, International Building and Residential Codes and other
ordinances of the Town applicable thereto.
X � �,
Owner/Owner's Representative Signature (Requir`ed)
Applicant Information
Applicant Name: 1� � S S �. �Orn �3� WS b4
Appliqnt Phone: 47� ��S - ya��
Electrical
Mechanical
Plumbing
Building
Valuation of
Work Included Plans Included Work
OYes �No OYes QNo "� %!
�Yes Q)No �Yes QNo N��
�Yes QjNo �Yes �No ��
�Yes oNo (�Yes �No
Value of all work being performed: $ I DO 00 0
�
(value based on IBC Sedion 109.3 & IRC Section 108.3)
Electrical Square Footage ►�% IQt
Detailed Scope and Location of Work: �i.�w v� ��c�Co�o �
�� S►t�nrr� . S�t..-c..to . wt..7�ew�. FRe,v+Qoc�Q
ST,Stf'�, �v*'�v sfRriOs ,. GA�-� �L,
APPlicant E-Mail: /'as�c�ombrd w sK� �COn�r4sf. � t{�1a n�� L� FC�4+ �o� � � A�/F� Gw�2� N�a+
Project Information�� ���- �°"���� S�3�d �►�y, F�4G�,T ��'i�S
Owner Name: �+'1�1J �IL�u�U
l-t�wt�L q-/�tf�kc P�4� "t'Ff/ZUUC/t n>o� .if�e'•trcli4..�
Parcel #: o�-I � 3- ld�-� ` dl - c�o a- � �
(For Parcel #, contact Eagle County Assessors OHice at (970-328�640 w vlsit r.�►.t� oFi= r� �' '�c �s
www.eaglecounty.us/patie)
For Office Use Only:
Fee Paid:��p`��J►9y
Received From:
Cash Check #
CC: Visa / MC Last 4 CC # exp date:
Auth #
(use additional sheet if necessary)
Date Received: D � � �� (, � �
AUG 2 3 �U1L
�
TOWN OF VAIL
� �,B�GHT
-� .�ASSOCIATEs
August 18, 2012
Town of Vail
Atrn: David Rhoades
75 South Frontage Rd
Vail, CO 81657
Re: Braun Remodel
1175 Casolar Del Norte Dr., #A
Vail, CO
To Whom It May Concern:
This letter is to inform you that Albright & Associates, Inc. has been retained by Sno-Away Inc. to
provide structural engineering design services for the remodel/renovation of the above referenced
property. We anticipate being involved through the demolition, design, and construction phases
of the project. Sno-Away Inc. is to provide documentation of our findings and recommendations
to the building department for review prior to construction. If you have any questions regarding
this project, please contact me for additional information.
Sincerely,
�
Jack L Albrig ,
Principal
12038L1
�.:��,,
�, .
=�^.�Q� � F(� /�+?.;
� �8'IZ �
�s� �
y y,
Afbright & Associates, INC � 970•927•4363 off1Ce � 970•927•3039 faX ' 4oz Park Ave., Unit E� Basalt, CO 8i6zi � www.albright-associates.com
�Sierra Pacific Windows
A Division of Sierra Pacific Industries
�� 309A Meadowview Lane
Basalt, CO 81621
sb�rs Pac��� , (970) 927-1726(Phone)
• M� (970)927-1727(Fax)
August 15, 2012
Sold To:
SNO-AWAY
PO BOX 4606
BASALT, CO 81621
(970)379-4286-Cell
(970)927-9028-Fax
ROSS DOMBROWSKI
-- Order Check LIs!
Species
Quantity
Operation
Rough Opening
� Glazing/Li1es
�---- _ _ —
- Warranty Informatlon
Llmlted Warranty
(Applies to these line item numbersJ
No Warranty
(Applies to these line item numbers)
Shop Drawings
Required
CUSTOMER ACCEPTANCE COPY �.se.o
3J30/2012
Order Number 91202396 Page 1 of 7
Terms : Cash on Delivery
Required Depoalt : 54,400.00
PO IF :
Job # :
Permit No # :
Box Screena : No
Box Hardware : Yea
Ship To:
VAIL REPLACEMENT
,CO
(970)379-4286-Cell
(970)927-9028-Fax
ROSS DOMBROWSKI
Jamb Size
Primed vs Clear
Exterior Trim
Hardware
Screens
Direct Ship: No
Subd{vfslon :
Tract Number:
Properly Location:
Properiy Owner:
SNO-AWAY
PO BOX 4606
BASALT, CO 81621
(970)379�286-Cell
(970)927-9028-Fax
ROSS DOMBROWSKI
Drawing Page(s)
O/S Purchase lead time
O/S Purchase warranty
WUI Compliant
Terms and Conditions
(Thls order is subject to the terms and conditions printed on the back page. Please read them before signing.)
Customer Slgneture
Sales RepSlgnature ______.._—_. - ---
--- -----------
Ryan Keser (870)927•1726
Date
Lender:
Owners ManuallSPW Warranty Color (Clad) 024 Bronze
Installation Instructions
Shop Drawings Required
(Exterior) (Interior) Distressed
Coloniat Contemporary
Order Summary
Net Total
8.40 Tax Rate
Labor Charge
Order Total
$ 10,063.30
$ 845.32
$ 0.00
$ 10,908.62
r_--
Hm Qty Product Code
1 1 C-WC-28 1/44B 1/4-2 i
I Casement
U-fec:0.29 SHGC:0.18
VL 0.39 CR: 44.00
2 1 C-WC-281/4481/42
Casemern
U-fec: 0.29 SHGC: D.18
Vt: 0.39 CR: 44.00
3 1 C-WC-24 3/1660 1/2-3
Casement
, U-fec: 0.29 SHGC: 0.19
i Vt: 0.39 CR: 44.00
4 1 C-WC-281/448 t142 ,
Caeement I
i U-fac:0.29 SHGC:0.1B
Vl: 0.39 CR: 44.00
5 1 C-WA-32 3/8201l2-1 -�
Awning
�
U-fac:0.31 SHGC:0.18
Vt: 0.39 CR: 41.00
6 1 C-WC-281/4491/4-2 ,
Casement �
U-tec:0.29 SHGC:0.18
Vt: 0.39 CR: 44.00
I
7 1 C-WA-401/42012-1 i
Awning
U-fac:0.31 SHGC:0.18 i
Vt: 0,39 CR: 41.00
8 1 C-WA�O 7/42012-1 ��
Awning
U-fec: 0.31 SHGC:0.18
Vt: 0.39 CR: 41.00 !
Order Number 81202396 Page 2 of 7 Initials:
p _ _ _..-- ----�-- -- ----- ------ - _ - --- ----_ _--
-- _ --- --,� _ r
Rough Opanlnp Uta w Jam
Wldth x Helght ' p er SYm Locstlon ! Glaze GrIBa Hardwaro Exterlor Slza Addltional
(lnchesl Optlons P�ttem T�^� pncherl Optlons
57 7/4 x 49 LR 1 FRONT ENTRY �Insulated i 1 Lite Bronze No BrickmouW ' 6 9l16" � Clad: 24
Vent Tubes - Hardware No Sill Nose Bronze
LoE'-366 Bronze Pine
Temp Int Int:- Screen Designer Sash
LoE-i89 TSL Clear Irrt.
' BetterVue Cntmp ProFle
-- - - - --I -- - -- ----___-- ---- - - - -- ---
57 114 x 49 LR 1 SIDE (EAST) Ilnsulated 1 Lite � Bronze No Brickmould 6 9116" Cled: 24
�VentTubes '-Hardware NoSiIlNose Bronze
� �LoE'J66 Bronze , iPine
Temp Int Int:- Screen Designer Sash
LoE-iB9 TSL Clear Int.
�i
BetterVue Cntmp Protile
-- - -� - _- --- -- - ----'---
73 5/16 x 61 114 LSR 2 FRONT DECK Ilnsulated 1 Lite Bronze No Brickmould 6 9116" Clad: 24
iVentTubes -Hardware �NoSiIlNose Bronze
'LoE'-366 Bronze P��
i Temp Int � Int:- Scree� Designer Sash
LoE-i89 ' TSl Clear Int.
' BetteNue Cnlmp Profile
57 1l4 x 49 LR 3 2ND FLR FRONT Ilnsuleted � 1 Lite - i Broaze No Brickmould 6 9176" Ciad: 24
Vent Tubes � �- Herdwere No Sill Nose � Bronze
LoE'�66 Bronze P��
Temp Int Inl:- Screen , Designer Sash
loE-i89 TSL Ctear Inl.
� �� BeUerVue � � Cntmp Profile
HC1412 Hinge I
- -- ----�------- -- ! -- -
33 1/8 x 21 114 X 4 2ND FLR BATH rnuleted 1 L'Re Bronze No Brickmould 6 9l16" Clad: 24
Tempered - Hardware No SiII Nose Bronze
I VentTubea Bronze Pine
LoE'-366 Int:• Screan Designer Sash
- - -ILoE-189 , BeqerVue Clear Int. - i
CMmp Profile
- - ---- -- - -- _ _ -�- - - - ----- -- - ------1- �_
57 1l4 x 49 LR 5 � 2ND FLR BE� �Ineulalad 1 Lite Bronze No Brickmould 6 9116" Cled: 24
IVent Tubes 1• Herdware No Sill Nose Bronze
LoE'-386 �Bronze Pine
ITemp Int InC- Screen I Designer Sash
LoE-i89 � TSL � Clear Int.
BetterVue Cntmp Profile �
� HCt412 Hinge
� � - -
-- - - - -
41 x 21 1/4 X 6 3RD FLOOR Insulated 1 Lfte Bronze No Brickmouk 8 9116" Clad: 24
Vent Tubes - Hardware No Sill Nose Bronze
LoE'J66 i Bronze Pine
Temp Int I InL•- Screen i Designer Saeh
ILoE-i89 BetterVue Clear Int.
� Cntmp Profile
-- �----- --- _
41x211/4 �X 8 3RDFLOOR �Inaulated 1LHe Bronze �oBrickmould 69N6" CIad:24
Vent Tubes - Hardware i No Sfll Nose 8ronze
loE'J66 Bronze ! Pine
Temp Int Ink- Screen � Designer Sash
LoE-ie9 Better✓ue � I Clear InL
I I Cntmp Profib
i
Itm �ty Produet Cods
i
9 1 C-WA-401f4201l2-1
Awning
Udac:0.31 SHGC:0.18
Vt: 0.39 CR: 47.00
--10' 1 C-WC-281/4481/4-2 -
Caeemant
�U-fac:029 SHGC:0,1B
� Vt: 0.39 CR: 44.00
Rouph Opening I
Width x Helght Oper Sym ' Locatlon
Il�chas) �
41 x 21 1/4 X 6 3RD FLOOR
Gisze
Optlons
ated
Tubes
366
� Int
57 1/4 x 49 LR 7 ' BACK SOUTH Insulated
VentTubas
LoE'�66
Temo Int
Order Number 91202396 Page 3 of 7 Initfals:
� IJte or Jam �
Grllle H��re ExteNor Siza � Addltlonal
Psttem Trlm Ii�hesl Optlom
1 Lite Brooze No Brickmould 6 9116" Clad: 24
- Hardwere No Sill Nose Bronze
Bronze Pine I
IM:- Scraen Designar Sash i
, BelterVue I Clear Int.
, CMmp Profile
---- --__ _ ---- -t---
1 LRe , 8ronze No BrickmouW 8 9/16" Cled: 24
- Hardware No Sill Nos� i Bronze
Bronze , Pine
Int:- Screen Designer Sash
� TSL ' Clear Int.
BetterVue i Cntmp Profile
HC 1412 Hinge
- ._. ._ ----- ---- - -I------ ----
111 1 � C-WCP-14 1/872-1 I 14 7/8 x �2 3!4 S 8 EAST Insuleled 1 Lite i No Hardware No Bdckmould 6 9/16" Clad: 24
i Casement Picture Vent Tubes No Screen No Sill Nose Bronze
; LoE'366 Pine
• Priced By Factory ' 'Temp Int ii Designer Sash
U-fec: 0.28 SHGC: 0.22 I ILoE-iB9 I Clear Int.
� Vt: 0.45 CR: 43.00 Cntmp Profib
1: MINIMUM ACTNE CASEMENT WIDTH IS 14-1/2". � __
12 1 C-WCP-14 11872-1 ' 14 7/8 x 72 3/4 S B EAST Ilnsulated 1 Lite No Hardwere No Brickmould 6 9/16" � Cled: 24
Casement Picture Vent Tubea No Screen No Sill Nose Bronze
'LoE'�66 Pine
` Priced By Factory
� Temp Int Designer Sesh
U-tac: 0.28 SHGC: 0.22 i LoE•i89 Clear Int.
i i CMmp Profile
Vt: 0.45 CR: 43.00 � — _—� --- _ i
�i _—
7: MINIMUM ACTIVE CASEMENT VJIDTH IS 14112". �
-- --- - -- -- - --- -__ - _ ----- -- --
- —r—r----- —
l---- --
13� 1 C-ID�679•1 53 x 81 12 1L �- ENTRY Insuleted j 1 Lite � VeronaRl6 � No Brickmould 6 9/16" Clad: 24
Inswing Door Clear OR Bra�s Bronze
i LoE'-272 -Trim Set Pine
Mulled Unit � Tempered OR Brass i Clear Int.
" Firot item in unit �, Venl Tubes - Hinqee
Head: 4 Sf8 , Keyed Lock
i Drewing Requirad Stile� 4 518 �I Spl Tnm Sets i
i
U-fec: 0.34 SHGC: 0.26 Kicic: 613/16 ' Brown - abn
14 �' Vt: 0.43 CR: 57.00 '
--- - ----------- -- ---- -__- _ . --- ---- - - _ —
C-IS-12 7/879-1 -> See item x 13 �0 ENTRY insulated 1 Lite Brown - Qbn No Brickmould , 6 9116" Clad: 24
Inswing Door Sidelite � Clear Br°^ze
�LoE'-272 I i Pine
-> See item # 13 � Tempered Clear Inl.
Vent Tubes
Drewing Required Head: 4 5/8
• Priced By Fectory Stile: 2 5/16
U-fec: 0.36 SHGC:0.19 Kick:613/16
VL 0.32 CR: 57.00
_ _.. ----- - - .:i.- ---
15 1 Boxed Window �
Herdwara-HOLD �
16 1 Custom Lock 8 Slide I ,
- �----- ---- -----1 -
REVIEW EGRESS AND SAFETY GLAZING RE�UIREMENTS. THE ADDITION OF SAFETY C�LAZING OR SPECIAL EGRESS HARDWARE MAY RESULT IN AN INCREASED PRICE.
i Rough Openlnp I
� Wldth x Helght 0 er Sym Locetlon
Itm I Oty Product Cods pnchss) P I �
Order Number 81202396
--- ---- Ute or
Glazs Odlle Herdwsre
Optlons _ I— -P�Karn I
Page 4 of 7 Initlals:
- -- 1 _ -�- -----
Jam
Enterlor Sizs Addltlonal
Trlm Optlons �
Iinchas) I
� --
Order Number 97202396
Page 5 of 7 Initials: _
Abbreviatlon Key ---- __ _ _ __ _.___ -_- _ - --
Glaze Optlons Hardware Optfons Ezterior Trim Addkional Optlona
Inauleted - Insulated Glass SIM DL - Simulated �ivided Lile TSL - Tendem Sash Lock SwinB Screen - Swirg Door Screen SMB = Stucco Brickmould ESH = EMended Sill Horn
SDL - Single Divided lite Lemi 1 Side - Leminete 1 Side FOL - foot Operaled Lock Life Finiah - Lifetime Finish ESN 2= Extended Sill Nose 2" Primed Int. - Primed Interlor
IDL - Insulated Divided Lite FCH - Folding Crank Handle ESN 3= E�ended Sill Nose 3" Clear Int. - Clear Interior
Primed Ext. • Primed Exterior
Clear Ext. - C�ear Exterior
-- ----- -------- ---- -- .. --
— __ ---- ----
Warranty InformaGon _- --- -- ____ -----
LIMITED WARRANTY: SieRa Pacific Windows warrants certain components only as more specHically described in the wntten limked Warranty end disclaims any other expreas or implied weRanty, includl�g, without
limitetion, any implied warrenty of inerchentabilRy or fitness for a particular purpose. The product ia not certified for air infiRration, water penetration, atructural loading, forced entry or hardware
loed testing. Damagee are iimited by the terms of lhe Limited Wercanty. Customer is advised fo cerefully review the Limited Warrenty for the specKic provinions epplicable to Ihe producta
purchased.
NO WARRANIY: Sierre Pecific Windows warrante ony that the product hes been menuFactured in eccordance with the specficetions contained in the order. Sierre Pec�c Wuidows diecleims eny olher exprene
or implied warranty, including, without limitatlon, any wercanty of inerchentabllity or Titness for a perticuler purpose.
r—
�
I
Disclaimer Information
Outside Purchase Items: Warranty covered by praduct menufacturePs spec�c warcanty.
Sedones withjambs greater than 4-9116: LimRed screen opening
Radfua Sedones: Limited sash openlnp _. _
- -- -----
Terms and CondlUona of Sa/e
1. TERMS: a. All C.O.D. orders are to be peid'm fuli to the delivery driver with either a Ceshier's Check or a personel check, preprinted with the Buyer's neme and eddrees, prior to unloading the order. On
h he e re-a roved the must be preseMed to the driver prior to unbading the order,
2. RIGHT TO LIEN:
3. ATTORNEY FEES:
4. ESTIMATE OR BIDS:
S.ORDERS:
orders w ere vouc re ar p pp , y
b. This quoted price includes a 3% discount tar payment mede in cesh, check, or other means not involving the use af a credit card. This discount is oftered to all prospective buyers. Payment
by Credit Card will waive this discount.
c. Na deductions mey be takan from the invoice amount unlesa euthorized by Sierre Pacific Windows prior to deflvery. Sierra Pacific Windows will not be reaponsible for any beck charges
resuNing from additional metariele or work peAormed by others (see Werranty for further Infarmetion)
d. Past due balances are subject to 1.556 monthly finance charge.
e. Any check or othar payment returned lo Sierta Pacific as the resuit oi insufficient funds or cenceled paymant will result in a$50 processing fee added to the order total.
a. In ihe event the contract emount is not paid fn full, Sierra PecHic Windows reservea the right to plece e lien or bond which may be asserted under eny proviaion of ihe lew, lo eecure peymanl
of the conlract amount.
e. If any lepal adion is required, Sierra Pecific Windows is entitled to recover reasoneble eltomey fees, court costs and ell other reesonable professionel expert or co�sultant fees and coats
releted to such Iegal action.
a. All pricing is good for 30 deya uNess specHicalty noted to the cantrery.
b. Sierra Pac�c Windows essumea rro responsibility for ertoro in takeoffa or pricing.
a. Upon signing, Customer agrees to all terms end conditions of this contract.
b. Orders are subject to delay due to strikes, fire, floods, accidents, w eny other cause beyoM our control. Sierra Pacitic Windows will not ba responsible for loss or demage beyond 'AS control,
c. Seller is not liable for praspective proffls ar special indired, consequentiel or incidental damages, nor may the recovery oi any kind apainst seller be greater in amount than the purchase price
of the specNic material sold end caueing the elleped loss damege or iryury.
6, CHANGE ORDERS: a. Order changes wlll only be accepted wdhin 3 daye ot signiny the original order.
b. Special order kams may only be changed or cancelled within 3 days from signing tha original order.
c. Cencellations may only be made within 3 days from signinp the original order.
d. Order chenges ere immediately binding. They da NOT ellow an edditionel 3 days for maditication or cencelletion.
e. Sierre Pecific Windowa reserves the righl to adjusl prices for order chenges made at lhe request ot the buyer at eny time following odginel order ecceptance.
f. Any chenge to the order may resuR in e delayed delNery date.
7. TAILGATE DELIVERY: a. Sierre Pecific Windows is not responsible tor lebor to unload. Buyer must provide sufficieni labor at the Job site when driver errivea.
b. Back orders will be noted on the peperwork end will deliver es eoon as possible.
c. Any dema miesinp or damaged muat be noted on the driver's paperwork at the time of delivery or it wil! be essumed complete end in good condkion.
d. Sierra Paclfic Windows is not reaponsible for goods picked up by buyer in his\her own vehicle.
8. SALES TAX: e. The Salea Tax rate in this quote is estimated at the time of tha quote. Customer agrees to pay the actual Sales Tax in effect et the time of delivery oT any portion of this arder.
�
�.
� ���
.�
.
♦ o�o.� er
fidc�w r�n�ic �wousTwes
Sierra Pacific Windows
Limited Warranty
Page 6 of 7 Initials:
This Limited Warranty is effective for Sierta Pacific Products manufactured on or after ApN 1, 2006 and installed in the continental United States and
Cenada, subject ro the stated conditioas and limitations. rUry previous wananties will contiuue to apply to products manufactured by Sierra Pacific pria to this
date. For additional infortnation, including care and maintenance instructions, instsllarion instructions and previous warrenties, refer to
www.siertapacificwiudows.wm or wntact your local Service Center at 1-800-8247744.
Insulated Glass - 20 Year Limited Warranty
Sie� Pacific Windows (SPq, as manufacturer, wartants the insulated glass supplied in iu window and door products against failure of the air seal due to
defects in materials or wod�anship for a penod of twenty (20) years from the date of manufacture. This warranry dces not include cracked or broken glass ar
damage to the produd resulting from accident, abusive handling, misuse, or shattering due to heat buildup. This wazranry does not indude any insulated uniu
that exceed 50 square feet in overall size. Should there be a failure of the air seal within the 6cst twenty (20) years of the warranty period, SPI will deliver to
the place of produa iastalla[ion either a replac��[ of insulated glass or sas6 glazed with insulated glass or will refuud the purchase price, at SPI's discretion.
Within a period of hvo (2) years from the date of manufachue, SPI will replace defective insulated glass at no chazge or will refund the purchase price, at SPI's
discretion. SPI shall not be responsible for repaineng or refinishing invdved in the replacement of glass.
After two (2) years from the date of manufachue through the end of the warranty period, SPI will replace defedive insWated glass or will refund the purchase
price, at SPI's discreuon. SPI shall not be responsible for the cost and azrangement of installation, repainting, refinishing or similar activities involved in the
replacement of glass.
Wood Components, Hardware, Weathervstripping and Scrcens - 10 Year Limited Wananry
SPI warTanis for a period of ten (10) years from the date of manufacture, that the wood components, hardware, weather-stripping and saeens which
accompany its products (the "Components") wil] be free from defects iu wor}�anship or materiais which might uoreasonably affect the produM's normal
functioning. WiHvn a period of two (2) years from the date of manufacmre, SPI will repair or replace any Components that are defective as ro worlrnianship or
materisls at no charge, or will refimd the purchase price, at SPI's discretion. SPI shall not be responsible for re-painting, refinishing or similar activities
connected with the repair or replaceme�t oFany Component.
After two (2) years from the date of manufacture through the end of the wamanry period, SPI will repair w replace arry Components that are defective as to
woriananship or materials at no chnrge, or will refund the purchase price, at SPI's discretion. SPI shall not be responsible for the cost and azrengement of
installation, repainting, refmishing or similar activities involved in the repair or replacement of any Compcment.
This wartanty shall be null and void if the customer fails ro properly finish, care for and protect all wood items against moisture and excessive dryness and
rnsure that all surfaces, interior and exterior, top and bottom, are thoroughly painted, vamished or sealed by accepted industry finishing stm�dazds. This
wananty shall not apply to any weather-stripping, vin}+Is or plastics to which any paints, vamishes or siains have been applied
M�al Clad Wartanty - 10 Year Limited Watranry
SPI will provide a limited ten QO) year warranry on the coating oo the metal cladding against cracking, checldng or peeling due to adhesion loss. In addition,
the coating is wartanted fa ten (10) yea� against chalking in excess of a number eight (8) rating based on ASiM D 421498 and against color change of more
than 6ve (5) Delta E units in accordance with AS7M D 2244-93. Within a period of two (2) yeazs from the date of manufacnue, SPI will repair or replace the
defective metal cladding at no charge, or witl refund the purchase price, az SPI's discre[ion.
ARer two (2) years from the date of manufachue through the end of the warronty paiod, SPI will repair or replace the defec[ive metel cladding, or will refund
the purchase price, at SPPs discretion. SPI shall not be responsible for the cost and coordination of installation associated with the repair or replacement of tt�e
defective metal cladding. On any replacement parts where new wood is a component, SPI shall not be responsible for repaiutiug, refinishing or similar
activities connected with such replacement This watranry accludes minute frachuing that may occur in proper fabrication procedures.
Warranty Couditions, Facclusions and Limitations.
This wartanty is limited to defects in workmanship aad materials and expressty excludes damage or defects caused by or arising frmn:
2�/
iranstganM
/� �
Llmtted Wa�ranty
o On-site damage occumng during consWCtion due to vandalism, acts of nature or any other cause beyond SPI's control.
o Improper handling or installation by the builder or consumer md/ar failure of the builder or coas�er ro follow mauufacturer's insauctions.
o Normal wear and tear, and nahual weathering of surfaces.
o Prolonged expowre to weather in thc unfinished and/or primed state.
o Nahually occurting cortosion or tamishing of hazdware finishes.
o Installation of the window or door in its opening in a manner which is not plutnb, square and we and adequately shimmed on all sides.
o Improper insffillation not in conformance with Siema PaciSc installation inshuctions: operaUOnal yroblems and problems related to water and/or air
infiltration/leaking as a result of improper installation or flaws in bwlding design or constructian.
o Strain which is applied to the unit by movement of the building or where provisions have not been made in accordance witli sound industry practices for
adequate e�cpansion or contraction of fraining members.
o Products subjected ro conditions e�cceeding their desig� size and/or design pressure limitations.
o Doors with ADA canpliant sills, special hardware or no hardware.
o Windows with special hardware or no hardware.
o Variations in the color, grain and texhue of wood products.
o Wood cellular structure failure for wood Canpon�u and any Components that come in direct contad with soil. Note: super6cial mold/mildew dces not
indicate wood cellular swct�e failure.
o Improper finishing and/or maintenance of wood Components.
o Wazping in door panels unless it exceeds 1!4" in the plane of the panel iuelf for doors up to 3'-6" x 7'-0" and/or 3/8" for doors ova 3'-6" x 7'-0". This
dces not refer to the relatioo of the door panel to the frame or jamb in which it is himg Action on any claim for wa�page may be deferred for a period of
time up to 12 months at SPPs opuon [o permi[ condiuoning of [he daor to humidiry and temperature ranges at the jobsi[e.
o Minor glass imperfections thai do not atFect nortnal vision or product perfamance per the guidelines established by ASTM C 1036-01.
o Glass breakage, failure due to misuse or abuse, and damage caused by failure to properly finish and provide maintenance, by alteration or modificatioa to
the window (e.g. automer applied tints or 61ms, paint finishes, sxwity systems), or as a result of eny cause beyond the controt of Sierts Pacific
(e.g. vandatism, fire, Flood, earthquake, other acts of nanue).
Effective 114/Ol/06
Page 7 of 7 Initials:
o Condensation, surface fogging or frou on exposed surFeces of windows or doors and arry related water damage which may occur as the natural result of
humidity within the sWcture or changes in interior/exterior temperatures. (Note: most condensation problems are related to excessive humidiry levels in
a sWcriue; contact a heating/air conditioniag specialist for help).
o Finish failures a corrosion of aluminum cladding or damage to oiher Canponeots ceused by chemicals or rnvironmentsl conditions including but not
limited to air pollutants, acid raiq chlorine, brickwash and salt spray.
o Corrosion, wear or failure of standard hardware or aluminum cladding in a seacoast or wrtosive environment.
o "C6alking" of the clad finish is not a defed unless it exceeds a numaical Taling of eight (8) when measured in accordance with the standard procedures
specified in ASTM D 421498. Fading or chauging in wlor of ihe "clad finis6" is not a defect unless it exceeds five (5) E units (NBS), calculated in
accadance with ASTM D 2244-93, paragraph 63. Color change shatl be measured on an euposed "clad finish" that has been cleaned of s�aface soils and
c6alk, and the corresponding values measured on the original or unexposed "clad 6nish." Fading or color char�ges may not be �mifortn if the swtaces are
not equalty e7cposed to the sun and elements. If the above ASTM standards change, the standards in effect at the time of purchase appty.
o Producu pw�chased Uvough SPI Windows that are manufactured by a third party (e.g. vinyl windows, skylites, custom hardware) are not wvered under
the t�ms of this wazranry. Refer to product manufacturer's warranty for terms of coverage.
NOTE: The perfortnance of paint and/or Components may vary based on installafion in eavironmenu of heavy selt spray, air pollutants, acid rain or other
wrrosive substances, as well as based on elevation, orientation, altitude and other atmospheric condiuoos. Namal, regular maintenance of the product is
roqirired ro maintein the appea�ance and to extend the finish ]ife.
It is recommended that thae be a systematic �esh water cleaning progiam ia effect in areas of high salt coucentratioq such as adjacent to the seashore and in
areas of industrial or caustic amiospheres, to prevent the accumulation of concentrated salt or caustic chemical deposits.
Products in these locations should be cleaned with mild detergent soap and wazer. This should be done every 3 months as a minimum, and more frequendy if
necessary, to minimi�P the build-up of salt or carosive residue. My chips or scratches must be repaired immediately and not left exposed to the elements.
Coosult the Sierra PaciSc Windows Owner Manusl for cleaning details.
Units subjec[ to the detrimental etTects oFair pollu[an(s or chemical or caustic washes will not be covered by tt�e tertns of ihis Warranry.
Alloca[ion of Risks of SPI Produc[ Perfmmance. Because some water infiltration must be mrticipated in all conswction, it is imperative that the wall system
be designed and consaucted to prope�iy manage moisture. SPI is not responsible for claims or damages caused by aoticipated or unanticipated water
infilvation; deficiencies in building design, co�struction and maintenauce; failure to install SPI products in accordance with SPl lnstallation Inshuctions; or
the use of SPI products in systems, such as barria wall systems, unless proper managanent of moim�re within tt�e wall system is incorpora[ed within the
desig� of the system. The detertnination of the suitability of all bwlding components, including the use of SPI products, as well as the design and installation
of flashing and sealing systems, are the responsibility of the buyer, owner, architect, contractor, installer, or other consWction professional and are not the
responsibiliry of SPI. All risks related to building design and construction, fimess of SPI product for a particular putpose, or the maintenance, installaGon, and
use of SPI products shall be assumed by the buyer and/or owner in conjuncrion with the architect, contractor, installer, or other conswction professional.
Thb Warrsoty sets fort6 our mavmum liabiliry for oar products. We s6s11 not be liable for special, indirect, consequential, or incidental damsges.
Your sole and eaclusive remMy with respect to aoy aod s1I losses or damaga resulting from any cause whatsoever shall be as specified hereio_ We
make o0 other warranty or guarantee, eithcr caprcss or impGed, induding implied warraotia of mcrchanMbility and of fitn�ss for a particWar
purpose to Me originsl purchaser or to any subsequeot user oi thc product, eacept as exprcssly contained hercin. In the event state or provincial law
preclude� e:clusion or limitation of implied warranNes, the duretion of aoy sucL wsrranties s6a11 be no longer than, and t6e time and manner of
praeo8ng any claim 6ereon s6a11 be the same as, that provided in the eipress warranty stated herein.
SPI does na warrant, expressly or impliedly, any special product or item that is manufactured according to speci6cations supplied by the consumer.
The wartanty on airy replacement product will extend fw the balance of the original wartanty period.
All warrdnty claims must be made within the applicable warianty period. SPI is giving you an express Limited Wananty. SPI cannot and shall not be liable to
you for arry other express or implied wartanties provided by distributors, dealers, salespersons or mry other rep�esentatives of SPI whether written or oral. Your
exclusive remedy sLall be repair, replscement or refimd as stated in this warranty. SPI, in its sole discrerion, may choose to repair the product as an opti� to
replacement in full satisfaction of its wazranty obligation.
Some states do not allow the exclusion or limitauon of incidental or wnsequential damages or limitarion of the duration of implied warranties, so the
limitations or exclusions set forth above may not apply ro you. Should an implied wazranty of machaniability or fitr�ess for a particular putpose apply to yoq
those warranees are limited in time to the dwation of this wartanty. This wartanty gives you specific legal rights and you may also have other rights [hat vary
6an s[ate to state.
Claim Proadare
To initiete a daim action imder t6is Limited Wananry, contact the SPl Tertirory Manager w6o sold you the products. In the evwt this person is unlmown,
please contact:
Your locat Service Center at 1-800-824-7744, or
Sierta Pacific Windows Customcr Savice Manager
PO Box 8489 Red Bluff, CA 96080
www. siertapaci ficwindows.com
You will be reqwred to provide the following infbrtnation: (a) your name, address and telephone number, (b) description of product for which claim is made;
(c) proof of daze of pureLase (invoice); (d) name of SPI sales represen[auve (if known); and (e) nahve of product failure and any fiirther pertinmt information.
SPI may ch�ge a fee for on-site product inspections. However, the fee will be fulty refunded if the produa is famd to contam a defect covered by this
waztanry.
Limited Wazranty (as de5ned by Mag�uson-Moss Wartanty-Federal Trade Commission ImProvanent Act)
Effective 04/Ol/06
Sierra Pacific Windows
Ryan Kaser
(970) 927-1726
Sold To: SNO-AWAY
PO BOX 4606
Ship To: VAI� REPLACEMENT
Drawings
91202396
August 15, 2012
Page 1 of 2
Item: 1 C-WC-28 1/448 1/4-2(LR)
Qty: 1
R0: 57 1/4 x 49
Jamb: 6 9/16
Loc: FRONT ENTRY
Sym: 1
Clad: 24-Branze
�
Item: 5 C-WA-32 3/820 1/2-1(X)
pty: 1
RO: 33 1/8 x 21 1/4
Jamb: 6 9/16
Loc: 2ND FLR BATH
Sym:4
Clad: 24-Bronze
Item: 2 C-VVC-28 1l448 1/4-2(LR)
Qty: 1
R0: 57 1/4 x 49
Jamb: 6 9/16
Loc: SIDE (EAS'n
Sym: 1
Clad: 24-Bronze
Item: 6 C-WC-28 1/448 114-2(LR)
Glty: 1
R0: 57 1l4 x 49
Jamb: 6 9116
Loc: 2ND FLR BED
Sym: 5
Clad: 24-Bronze
Item: 3 C-WC-24 3/1660
1/2-3(LSR)
Qty: 1
RO: 73 5/16 x 61 1/4
Jamb: 6 9/16
Loc: FRONT DECK
Sym: 2
Clad: 24-Bronze
�
�
Item: 7 C-WA-40 1/420 1/2-1(X)
Qty: 1
RO: 41 x 21 1/4
Jamb: 8 9/16
Loc: 3RD FLOOR
Sym: 6
Clad: 24-Bronze
All Window/Door operations are viewed from exterior. Pictures are NOT to scale. They are offered as a rough
approximation of design and muliing sequence, therefore CAD drawings may still be required on some units.
Item: 4 C-WC-28 1/448 1/4-2(LR)
Qty: t
RO: 57 1/4 x 49
Jamb: 6 9/16
Loc: 2ND FLR FRONT
Sym: 3
Clad: 24-Bronze
�
Item: S C-WA-40 1/420 1/2-1(X)
Qty: 1
RO: 41 x 21 1/4
Jamb: 6 9/18
Lx: 3RD FLOOR
Sym: 6
Clad: 24-Bronze
Sierra Pacific Windows
Ryan Kaser
(970)927-1726
�I'
Item: 9 C-WA-40 1/420 1/2-1(X)
Qly: 1
RO: 41 x 21 1/4
Jamb: 6 9/16
Loc: 3RD FLOOR
Sym: 6
Ciad: 24-Bronze
. T
Item: 13 C-ID-3679-1(L)
Item: 14 C-IS-12 7/879-1(0)
Qty: 1
R0: 53 x 81 1/2
Mulled Unit
Jamb: 6 9/16
loc: ENTRY
Sym:
Ciad: 24-Bronze
Sold To: SNO-AWAY
PO BOX 4606
Ship To: VAIL REPLACEMENT
Item: 10 C-WC-28 1/448
1/4-2(LR)
Qty: 1
RO: 57 1/4 x 49
Jamb: 6 9/16
Loc: BACK SOUTH
Sym: 7
Clad: 24-Bronze
Item: 11 C-WCP-141/872-1(S)
Qty: 1
RO:147/8x723/4
Jamb: 6 9/16
Loc: EAST
Sym: 8
CIad:24-Bronze
All Window/Door operations are viewed from exterior. Pictures are NOT to scale. They are offered as a rough
approximation of design and mulling seque�ce, therefore CAD drawings may stitl be required on some units.
Drawings
91202396
August 15, 2012
Page 2 of 2
Item: 12 C-WCP-14 1/872-1(S)
Qty: 1
R0: 14 7/8 x 72 3/4
Jamb: 6 9/16
Loc: EAST
Sym: 8
Clad: 24-Bronze
____._� �---- ---- --------
�oER r°Ilo2-a.�
JOB NAME — �
WOOD CLAD COLOR _ ��
; � YES NO
O
RADIUS RISE
�
DIRECT SEf NO SASH - A B C
� YES NO
;
� �/e — �-s/�d — � —
� ro�P s�c
LOCKRAIL �
� L7TE PAT
' OTHER
�
4—t/8 4-9/18
,�
6-1/a b-9/tE
8-11/18 OTHER
�
STAT OPER
�
BM � SBM
oni�
COLOR
KEYED LOCKED
� on�eR
DRAWING
vl EWED FROM
EXTERIOR
rrEU r �
SHIP WK:
INSWING
80.� ---• 4.625
[6'-8 3/4 � "�_��
68.
CADD# WA-254081-33A
t.ocnnor� srueo�
.31 �
6. 12
27.750 NG 9.249
36.000 PANEL NGO
37.688 12.875
— [3'-1 11/16 PANEL
FRAME � 4•563
FRAMf
_�4� 5� 2�14
/
, p.��� C-�S-����
C1
SALES PERSON
3 uwr.Fc
DATE: OS-15-12 IDIMENSIONS NET OUTSIDE OF FRAME
CUSTOMER SIGNATURE:
OUTSULATION° SMD SYSTEMTM
(Formerly SPRINT° MD SYSTEM°)
:
�►n �xienor nran inswat�on ana rm�sh 5ystem with
� �COmP�Y
d r vi ���
�
_y-
DS158
OUTSULATION SMD SYSTEM
(Formerly SPRINT MD SYSTEM)
Specification
Outsulation SMD System (formerly Sprint MD System) Specification DS158
INTRODUCTION
This document contains the Manufacturer's Standard Specification for the Outsulation SMD System. These
specifications follow the Construction Specification Institute's 3-part format.
TAILORING THE DRYVIT MANUFACTURER'S SPECIFICATIONS TO YOUR PROJECT.
These specifications cover the most common ways of using the Outsulation SMD System. Most projects use
only a few of the possible combinations of these materials and methods. To tailor the specifications to your
Outsulation SMD project, simply use those sections which apply. Also, it may be prudent to place certain parts
of the Dryvit Outsulation SMD System Specification in other parts of the projecYs total specification, such as
sealants and framing. The project design professionals are responsible for ensuring that the project
specifications are suitable for the project. For assistance in preparing your specification, contact your Dryvit
Distributor or Dryvit Systems, Inc.
U N ITS
English Units are included in parentheses after the Standard International (SI) equivalents thus:
12.7 mm (1/2 in) 16 Kg/m3 (1.0 pcf)
Please note that the conversions may not be exact but rather represent commonly used equivalents.
WARNING
The Outsulation SMD System is designed as a drainage wall cladding system and is detailed to discharge
incidental moisture from within the System. Specifications should be followed and proper details adhered to, in
order to prevent water intrusion, resulting in possible damage to the System or other building elements. Care
should be taken to insure that all building envelope elements, including without limitations, roof designs,
windows, flashings, sealants, etc., are compatible with this system.
DISCLAIMER
Information contained in this specification conforms to standard detail and product recommendations for the
installation of the Dryvit Outsulation SMD System products as of the date of publication of this document and is
presented in good faith. Dryvit Systems, Inc. assumes no liability, expressed or implied, as to the architecture,
engineering or workmanship of any project. To insure that you are using the latest, most complete information
visit our website at www.dryvit.com, or contact Dryvit Systems, Inc., at
One Energy Way
P. O. Box 1014
West Warwick, RI 02893
(401) 822-4100
FAX: (401) 822-1980
* The Trained Contractor Certificate referenced in Section 1.06.A.2 indicates certain employees of the company
have been instructed in the proper application of Dryvit products and have received copies of Dryvit's
Application Instructions and Specifications. The Trained Contractor Program is not an apprenticeship or
endorsement. Each trained contractor is an independent company experienced in the trade and bears
responsibility for its own workmanship. Dryvit Systems, Inc. assumes no liability for the workmanship of a
trained contractor.
2
Outsulation SMD System (formerly Sprint MD System) Specification DS158
DRYVIT SYSTEMS, INC.
ARCHITECTURAL SPECIFICATION
SECTION 07240
OUTSULATION SMD SYSTEM
AN EXTERIOR INSULATION AND FINISH SYSTEM CLASS PB
PARTI-GENERAL
1.01 SUMMARY
A. This document is to be used in preparing specifications for projects utilizing the Dryvit Outsulation SMD System. For
complete product description and usage refer to:
1. Dryvit Outsulation SMD Data Sheet, DS441
2. Dryvit Outsulation SMD System Application Instructions, DS123.
3. Dryvit Outsulation SMD System Installation Details, DS163.
B. Related Sections
1. Unit Masonry - Section 04200
2. Concrete - Sections 03300 and 03400
3. Light Gauge Cold Formed Steel Framing - Section 05400
4. Wood Framing - Section 06100
5. Sealant - Section 07900
6. Flashing - Section 07600
1.02 REFERENCES
A. Section Includes
1. ASTM B 117 (Federal Test Standard 141A Method 6061) Standard Practice for Operating Salt Spray (Fog) Apparatus
2. ASTM C 150 Standard Specification for Portland Cement
3. ASTM C 297 Standard Test Method for Flatwise Tensile Strength of Sandwich Constructions
4. ASTM C 1177 Standard Specification for Glass Mat Gypsum Substrate for Use as Sheathing
5. ASTM C 1396 (formerly C 79) Standard Specification for Gypsum Board
6. ASTM D 968 (Federal Test Standard 141A Method 6191) Standard Test Methods for Abrasion Resistance of Organic
Coatings by Falling Abrasive
7. ASTM D 2247 (Federal Test Standard 141 A Method 6201) Standard Practice for Testing Water Resistance of
Coatings in 100% Relative Humidity
8. ASTM D 2898 Standard Test Method for Accelerated Weathering of Fire-Retardant-Treated Wood for Fire Testing
9. ASTM D 3273 Standard Test Method for Resistance to Growth of Mold on the Surface of Interior Coatings in an
Environmental Chamber
10. ASTM D 4060 Standard Test Method for Abrasion Resistance of Organic Coatings by the Taber Abraser
11. ASTM E 84 Standard Test Method for SurFace Burning Characteristics of Building Materials
12. ASTM E 96 Standard Test Methods for Water Vapor Transmission of Materials
13. ASTM E 330 Test Method for Structural Performance of Exterior Windows, Doors and Curtain Walls by Uniform Static
Air Pressure Difference
14. ASTM E 331 Test Method for Water Penetration of Exterior Windows, Skylights, Doors and Curtain Walls by Uniform
Static Air Pressure Difference
15. ASTM E 2098 Test Method for Determining the Tensile Breaking Strength of Glass Fiber Reinforcing Mesh for use in
Class PB Exterior Insulation and Finish Systems (EIFS), after Exposure to Sodium Hydroxide Solution.
16. ASTM E 2134 Test Method for Evaluating the Tensile-Adhesion Performance of Exterior Insulation and Finish
Systems (EIFS)
17. ASTM E 2273 Test Method for Determining the Drainage E�ciency of Exterior Insulation and Finish Systems (EIFS)
Clad Wall Assemblies
18. ASTM E 2430 Standard Specification for Expanded Polystyrene (EPS) Thermal Insulation Boards for use in Exterior
Insulation and Finish Systems (EIFS)
19. ASTM E 2485 (formerly EIMA Std. 101.01) Standard Test Method for Freeze-Thaw Resistance of Exterior Insulation
and Finish Systems (EIFS) and Water-Resistive Barrier Coatings
20. ASTM E 2486 (formerly EIMA Std. 101.86) Standard Test Method for Impact Resistance of Class PB and PI Exterior
Insulation and Finish Systems (EIFS)
21. ASTM G 155 (Federal Test Standard 141A Method 6151) Standard Practice for Operating-Xenon Arc Light
Apparatus, for Exposure of Nonmetallic Materials
22. DS123, Dryvit Outsulation SMD System Application Instructions
23. DS131, Dryvit Expanded Polystyrene Insulation Board Specification
24. DS151, Custom BrickT" Polymer System Specifications for Use on Vertical Walls
25. DS152, Dryvit Cleaning and Recoating
26. DS153, Dryvit Expansion Joints and Sealants
27. DS159, Dryvit Water Vapor Transmission
28. DS163, Dryvit Outsulation SMD System Installation Details
29. DS235, Dryvit Homeowner's Maintenance Guide
30. DS494, Dryvit AquaFlash� System
31. Mil Std E5272 Environmental Testing
Outsulation SMD System (formerly Sprint MD System) Specification DS158
32. Mil Std 810B Environmental Test Methods
1.03 DEFINITIONS
A. Base Coat: Material used to encapsulate one or more layers of reinforcing mesh fully embedded that is applied to the
outside surface of the Polyisocyanurate insulation board.
B. Building Expansion Joint: A joint through the entire building structure designed to accommodate structural movement.
C. Contractor: The contractor that instalis the Outsulation SMD System to the substrate.
D. Dryvit: Dryvit Systems, Inc., the manufacturer of the Outsulation SMD System, a Rhode Island corporation.
E. Expansion Joint: A structural discontinuity in the Outsulation SMD System.
F. Finish: An acrylic-based coating, available in a variety of textures and colors that is applied over the base coat.
G. Insulation Board: Polyisocyanurate insulation board, which is affixed to the substrate and Expanded Polystyrene used as
foam shapes where applicable.
H. Mechanical Fasteners: A combination of polypropylene washers and corrosion resistant fasteners used to secure the
insulation board to the substrate.
I. Reinforcing Mesh: Glass fiber mesh(es) used to reinforce the base coat and to provide impact resistance.
J. Sheathing: A substrate in sheet form.
K. Substrate: The material to which the Outsulation SMD System is a�xed.
L. Substrate System: The total wall assembly including the attached substrate to which the Water-Resistive Barrier is a�xed.
1.04 SYSTEM DESCRIPTION
A. General: The Dryvit Outsulation SMD System is an Exterior Insulation and Finish System (EIFS) Class PB, designed for
use on combustible type construction. Outsulation SMD System is installed over a code approved water-resistive barrier
and consists of a drainage medium and drainage accessories, an approved Polyisocyanurate insulation board,
mechanical fasteners, base coat with reinforcing mesh and finish.
B. Acceptable system configuration options include:
System Water-Resistive Drainage Medium Polyisocyanurate Attachment Base Coat
Confi uration Barrier Minimum Thickness
1 Backstop NT or Drainage Mat or 15.9 mm (5/8 in) Mechanical Genesis� or
Sheet membrane D it MD S cerTM Fasteners Genesis0 DM
2 Tyvek N/A 15.9 mm (5/8 in) Mechanical Genesis or
StuccoWra Fasteners Genesis DM
C. Design Requirements
1. Acceptable substrates for the Outsulation SMD System shall be:
a. APA Exterior or Exposure 1 rated Plywood, Grade C-D or better, nominal 12.7 mm (1/2 in), minimum
4-ply.
b. APA Exposure 1 rated Oriented Strand Board (OSB), nominal 12.7 mm (1/2 in).
c. Unglazed brick, cement plaster, concrete or masonry (water-resistive barrier not required).
d. Exterior sheathing having a water-resistant core with fiberglass mat facers meeting ASTM C 1177.
e. Exterior grade gypsum sheathing meeting ASTM C 1396 (formerly C 79) requirements for water resistant core or
Type X core at the time of application of the Outsulation SMD System.
f. Exterior grade fire retardant treated plywood.
2. Deflection of substrate systems shall not exceed 1/240 times the span.
3. The substrate shall be flat within 6.4 mm (1/4 in) in a 1.2 m(4 ft) radius.
4. The slope of inclined surFaces shall not be less than 6:12. The length of inclined surfaces shall not exceed 305 mm
(12 in).
5. At horizontal sealant joints and windowsills projecting 102 mm (4 in) or less, the slope shall not be less than 3:12.
6. All areas requiring an impact resistance classification higher than "standard", as defined by ASTM E 2486 (formerly
EIMA Standard 101.86), shall be as detailed in the drawings and described in the contract documents. Refer to
Section 1.04.D.1.a.4) of this specification.
7. Expansion joints
a. Design and location of expansion joints in the Outsulation SMD System is the responsibility of the project designer
and shall be noted on the project drawings. As a minimum, expansion joints shall be placed at the following
locations:
1) Where expansion joints occur in the substrate system.
2) Where building expansion joints occur.
3) At floor lines in wood frame construction.
4) At floor lines of non-wood frame buildings where significant movement is expected.
5) Where the Outsulation SMD System abuts dissimilar materials.
6) Where the substrate type changes.
7) In continuous elevations at intervals not exceeding 23 m(75 ft).
8) Where significant structural movement occurs such as changes in roofline, building shape or structural system.
4
Outsulation SMD System (formerly Sprint MD System) Specification DS158
8. Terminations
a. Prior to applying the Dryvit Outsulation SMD System, wall openings shall be wrapped with Dryvit AquaFlash System
or Flashing Tape. Refer to Dryvit Outsulation SMD System Installation Details, OS163.
b. The Outsulation SMD System shall be held back from adjoining materials around openings and penetrations such
as windows, doors and mechanical equipment a minimum of 12.7 mm (1/2 in) for sealant application. See Dryvit's
Outsulation SMD System Installation Details, DS163, for exceptions and alternate methods.
c. At the base of walls, the Outsulation SMD System shall extend a minimum of 25 mm (1 in) below the sill plate onto
the foundation and be terminated a minimum of 203 mm (8 in) above finished grade.
d. For slab-on-grade, the Outsulation SMD System shall extend a minimum of 25 mm (1 in) onto the slab edge.
e. Sealants
1) Shall be manufactured and supplied by others.
2) Shall be compatible with the Outsulation SMD System materials. Refer to current Dryvit publication DS153 for
listing of sealants tested by sealant manufacturer for compatibility.
3) The sealant backer rod shall be closed cell.
9. Vapor Retarders - The use and location of vapor retarders within a wall assembly is the responsibility of the project
designer and shal� comply with local building code requirements. The type and location shall be noted on the project
drawings and specifications. Vapor retarders may be inappropriate in certain climates and can result in condensation
within the wall assembly. Refer to Dryvit Publication DS159 for additional information.
10. Dark Colors - The use of dark colors must be considered in relation to wall surface temperature as a function of local
climatic conditions. Use of dark colors in high temperature climates can affect the performance of the system.
11. Flashing: Flashing shall be provided at all roof-wall intersections, windows, doors, chimneys, decks, balconies and
other areas as necessary to prevent water from getting behind the Outsulation SMD System.
D. Performance Requirements
1. The Outsulation SMD System shall have been tested as follows:
a. Durability
1) Air/Water-Resistive Barrier Coating
TEST TEST METHOD CRITERIA RESULTS
Tensile Bond ASTM C 297/E 2134 Minimum 104 kPa (15 psi) Substrate: Minimum 131 kPa
ICC ES AC 212 ' � g Si
Freeze Thaw ASTM E 2485/ICC ES Proc. No deleterious effects after 10 cycles Passed — No deleterious
AC 212 ` effects after 10 cles
Water Resistance ASTM D 2247 No deleterious effects after 14 days No deleterious effects after
ICC ES AC 212 " ex sure 14 da s ex osure
Water Vapor ASTM E 96 Proc. B Vapor Permeable 7 perms
Transmission ICC ES (AC 212)'
Air Leakage ASTM E 283 No Criteria Less than 0.6 Umin/m (0.002
cfm/ftZ
Structural ASTM E 1233 Proc. A Minimum 10 positive cydes at 1/240 Passed
Performance ICC ES (AC 212)' deflection; No cracking in field, at joints or
interface with flashin
Racking ASTM E 72 No cracking in field, at joints or interface with Passed
ICC ES (AC 212)' flashing at net deflection of 32 mm
1/8 in
ResVained ICC ES (AC 212)* 5 cycles; no cracking in field, at joints or Passed
Environmental interface with flashing
Water Penetration ASTM E 331 No water penetration beyond the inner-most Passed
ICC ES (AC 212)` plane of the wall after 15 minutes at
137 Pa 2.86 s
Weathering ICC ES Proc. 210 hours of exposure Passed
UV Exposure ICC ES (AC 212)*
Accelerated ICC ES Proc. 25 cydes of drying and soaking Passed
Aging ICC ES (AC 212)*
Hydrostatic AATCC 127 21.6" water column for 5 hours Passed
Pressure Test ICC ES (AC 212)
Surface Buming ASTM E 84 Flame Spread < 25 Passed
Characteristics Smoke Developed < 450
; AC 212 — Acce tance Criteria for Water-Resistive Coatin s Used as Water-Resistive Barriers Over Euterior
Outsulation SMD System (formerly Sprint MD System) Specification DS158
2) System
TEST TEST METHOD CRITERIA RESULTS
Abrasion Resistance ASTM D 968 No deleterious effects after No deleterious effects after
5001iters 528 uarts 10001iters 1056 uarts
Accelerated Weathering ASTM G 155 Cycle 1 No deleterious effects after No deleterious effects after
2000 hours 5000 hours
ASTM G 154 Cycle 1(QUV) No deleterious effects after
5000 hours
Freeze-Thaw ASTM E 2485 (formeriy No deleterious effects after Passed - No deleterious
EIMA 101.01 60 c cles effects after 90 c cles
ASTM C 67 modified No deleterious effects after Passed - No deleterious
60 c cles effects after 60 c des
ASTM E 2485lICGES Proc. No deleterious effects after Passed - No deleterious
AC235 '°" 10 c cles effects after 10 c cles
Mildew Resistance ASTM D 3273 No growth during 28 day No growth during 60 day
ex sure riod ex osure eriod
Water Resistance ASTM D 2247 No deleterious effects after No deleterious effects after
14 da s ex osure 42 da s ex osure
Taber Abrasion ASTM D 4060 N/A Passed 1000 cycles
Salt Spray Resistance ASTM B 117 No deleterious effects after No deleterious effects after
300 hours ex sure 1000 hours ex osure
Water Penetration ASTM E 331 No water penetration beyond Passed 15 minutes at
ICC ES (AC 235)*'* the inner-most plane of the 137 Pa (2.86 ps�
wall after 15 minutes at
137 Pa 2.86 s
Water Vapor ASTM E 96 Vapor permeable Quik-R 1.7 perm-inch
Transmission Base Coat' 40 Perms
Finish"` 40 Perms
Drainage Efficiency ASTM E 2273 Minimum Drainage Efficiency Passed
ICC ES AC 235 *** of 90%
* Base Coat perm value based on Dryvit Genesis
*' Finish perm value based on Dryvit Quarzputz
"' AC 235 — Acce tance Criteria for EIFS Clad Draina e Wall Assemblies
3) SVuctural
TEST TEST METHOD CRITERIA RESULTS
Tensile Bond ASTM C 297/E 2134 Minimum 104 kPa (15 psi) — Minimum 213.6 kPa (31 psi)
insulation failure
Transverse wnd Load ASTM E 330 Withstand positive and negative Minimum 4.3 kPa (90 ps�
wind loads as specified by the
buildin code
4) Impact Resistance: In accordance with ASTM E 2486 (formerly EIMA Standard 101.86).
Outsulation SMD System (formerly Sprint MD System) Specification DS158
2. The Outsulation SMD Components shall have been tested for:
a. Durabiliry
TEST TEST METHOD CRITERIA RESULTS
Reinforcing Mesh
Alkali Resistance of ASTM E 2098 (formerly > 21dN/cm (120 pli) retained Passed
Reinforcin Mesh EIMA 105.01} tensile strength after exposure
Polyisocyanurate
(Physical Properties)
Density ASTM D 1622 32 kg/m3 (2.0 Ib/ft3) Pass
Thermal Resistance ASTM C 177, C 518 5.6 @ 23.9 °C (75 °F) Pass
Water Absorption ASTM C 272 2.55 % max. by volume Pass
Compressive Strength ASTM D 1621 179 kPa (26 psi) min. Pass
Flexural Strength ASTM C 203 814 kPa (118 psi) min. Pass
Ftame Spread ASTM E 84 25 max. Pass
Smoke Developed 450 max. Pass
1.05 SUBMITTALS
A. Product Data — The contractor shall submit to the owner/architect the manufacturer's product data sheets describing
products, which will be used on this project.
B. Samples: The contractor shall submit to the owner/architect two (2) samples of the Outsulation SMD System for each
finish, texture and color to be used on the project. The same tools and techniques proposed for the actual installation
shall be used. Samples shall be of sufficient size to accurately represent each color and texture being utilized on the
project.
C. Test Reports — When requested, the contractor shall submit to the owner/architect copies of selected test reports verifying
the performance of the Outsulation SMD System.
1.06 QUALITY ASSURANCE
A. Qualifications:
1. System Manufacturer: Shall be Dryvit Systems, Inc. All materials shall be manufactured or sold by Dryvit and
shall be purchased from Dryvit or its authorized distributors.
a. Materials shall be manufactured at a facility covered by a current ISO 9001:2000 and ISO 14001:2004 certification.
Certification of the facility shall be done by a registrar accredited by the American National Standards Institute,
Registrar Accreditation Board (ANSI-RAB).
2. Contractor: Shall be knowledgeable in the proper installation of the Dryvit Outsulation SMD System and shall be
experienced and competent in the installation of Exterior Insulation and Finish Systems. Additionally, the contractor
shall possess a current Outsulation SMD System Trained Contractor Certificate*, issued by Dryvit Systems, Inc.
3. Insulation Board Manufacturer: Shall be Dow Chemical Corporation for Quik-RT"' Wall Insulation or Atlas Roofing
Corporation for Atlas StuccaShield0.
B. Regulatory Requirements:
1. The insulation board shall be separated from the interior of the building by a minimum 15-minute thermal barrier.
2. The use and maximum thickness of insulation shall be in accordance with the applicable building codes.
C. Certification
1. The Outsulation SMD System shall be recognized for the intended use by the applicable building code(s).
D. Mock-Up
1. The contractor shall, before the project commences, provide the owner/architect with a mock-up for approval.
2. The mock-up shall be of suitable size as required to accurately represent the products being installed, as well as each
color and texture to be utilized on the project.
3. The mock-up shall be prepared with the same products, tools, equipment and techniques required for the actual
applications. The finish used shall be from the same batch that is being used on the project.
4. The approved mock-up shall be available and maintained at the job site.
1.07 DELIVERY, STORAGE AND HANDLING
A. All Dryvit materials shall be delivered to the job site in the original, unopened packages with labels intact.
B. Upon arrival, materials shall be inspected for physical damage, freezing or overheating. Questionable materials shall not
be used.
1. Materials shall be stored at the jobsite in a cool, dry location, out of direct sunlight, protected from weather and other
sources of damage. Minimum storage temperature shall be as follows:
a. Demandit�, Revyvit�: 7° C(45° F)
b. AmeristoneTM, TerraNeo and LymestoneTM': 10 °C (50 °F)
c. DPR, PMRT'", E Finishes"', Color PrimeTM and Genesis 4°C (40 °F)
d. Custom Brick Finish: Refer to Custom Brick Polymer Specification, DS151
e. For other products, refer to specific product data sheets
2. Maximum storage temperature shall not exceed 38 °C (100 °F). NOTE: Minimize exposure of materials to
temperatures over 32 °C (90 °F). Finishes exposed to temperatures over 43 °C (110 °F) for even short periods
may exhibit skinning, increased viscosity and should be inspected prior to use.
7
Outsulation SMD System (formeriy Sprint MD System) Specification DS158
C. Protect all products from inciement weather and direct sunlight.
1.08 PROJECT CONDITIONS
A. Environmental Requirements
1. Application of wet materials shall not take place during inclement weather unless appropriate protection is provided.
Protect materiais from inclement weather until they are completely dry.
2. At the time of application, the minimum air and wall surface temperatures shall be as follows:
a. Demandit, Revyvit: 7 °C (45 °F)
b. Ameristone, TerraNeo and Lymestone: 10 °C (50 °F)
c. DPR, PMR, E Finishes, Color Prime and Genesis: 4°C (40 °F)
d. Custom Brick Finish: refer to Custom Brick Polymer Specification, DS151
e. For other products, refer to specific product data sheets
3. These temperatures shall be maintained with adequate air ventilation and circulation for a minimum of 24 hours
(48 hours for Ameristone, TerraNeo and Lymestone) thereafter, or until the products are completely dry. Refer to
published product data sheets for more specific information.
B. Existing Conditions - The contractor shall have access to electric power, clean water, and a clean work area at the
location where the Dryvit materials are to be applied.
1.09 SEQUENCING AND SCHEDULING
A. Installation of the Outsulation SMD System shall be coordinated with other construction trades.
B. Sufficient manpower and equipment shall be employed to ensure a continuous operation, free of cold joints, scaffold lines,
texture variations, etc.
1.10 WARRANTY
A. Dryvit Systems, Inc. shall provide a written limited moisture drainage warranty combined with a written limited materials
warranty against defective material upon written request. Dryvit shall make no other warranties, expressed or implied.
Dryvit does not warrant workmanship. Full details are available from Dryvit Systems, Inc.
B. The applicator shall warrant workmanship separately. Dryvit shall not be responsible for workmanship associated with
installation of the Outsulation SMD System.
1.11 DESIGN RESPONSIBILITY
A. It is the responsibility of both the specifier and the purchaser to determine if a product is suitable for their intended use.
The designer selected by the purchaser shall be responsible for all decisions pertaining to design, detail, structural
capability, attachment details, shop drawings and the like. Dryvit has prepared guidelines in the form of specifications,
application details, and product data sheets to facilitate the design process only. Dryvit is not liable for any errors or
omissions in design, detail, structural capability, attachment details, shop drawings, or the like, whether based upon the
information prepared by Dryvit or otherwise, or for any changes which purchasers, specifiers, designers, or their
appointed representatives may make to DryviYs published comments.
1.12 MAINTENANCE
A. Maintenance shall follow the procedures noted in the Dryvit Homeowner's Maintenance Guide, DS235, and repair shall
follow the procedures noted in the Dryvit Outsulation SMD System Application Instructions, DS123.
B. All Dryvit products are designed to require minimal maintenance. However, as with all building products, depending on
location, some cleaning may be required. See Dryvit publication DS152 on Cleaning and Recoating.
C. Sealants and Flashings shall be inspected on a regular basis and repairs made as necessary.
PARTII-PRODUCTS
2.01 MANUFACTURER
A. All components of the Outsulation SMD System shall be supplied or obtained from Dryvit or its authorized distributors.
Substitutions or additions of materials other than specified will void the warranty.
2.02 MATERIALS
A. Portland Cement: Shall be Type I or II, meeting ASTM C 150, white or gray in color, fresh and free of lumps.
B. Water: Shall be clean and free of foreign matter.
2.03 COMPONENTS
A. AirlWater-Resistive Barrier Components:
1. Water-Resistive Barrier Coating
a. Dryvit Backstop NT: A flexible, polymer-based, noncementitious water-resistive coating available in Texture and
Smooth.
b. Dryvit Grid TapeTM': An open weave fiberglass mesh tape with pressure sensitive adhesive available in rolls
102 mm (4 in) wide by 91 m(100 yd) long.
2. Sheet Type Membranes (by others)
a. Code approved water-resistive barrier such as but not limited to Dupont Tyvek StuccoWrap, Tyvek Home Wrap or
Commercial Wrap, #15 Felt, Grade D Paper.
B. Flashing Materials: Used to protect substrate edges at terminations.
1. Liquid Applied: An extremely flexible water-based polymer material, ready for use.
a. Shall be AquaFlash and AquaFlash Mesh
�
Outsulation SMD System (formerly Sprint MD System) Specification DS158
2. Sheet Type:
a. Shall be Flashing Tape and Surface Conditioner
1) Dryvit Flashing TapeTM': A high density polyethylene film backed with a rubberized asphalt adhesive available in
rolls 102 mm (4 in), 152 mm (6 in) and 229 mm (9 in) wide by 23 m(75 ft) long.
2) Dryvit Flashing Tape Surface ConditionerTM': A water-based surface conditioner and adhesion promoter for the
Dryvit Flashing Tape.
C. Dryvit AP AdhesiveTM': A moisture cure, urethane based adhesive used to adhere the Dryvit Drainage Strip and Drainage
Track
D. Accessories
1. Drainage Track (Optional - not required when Drainage Strip is specified): UV treated PVC perforated "J" channel with
weep holes, complying with ASTM D 1784 and ASTM C 1063. Shall be one of the following:
a. Starter Trac STWP - without drip edge by Plastic Components, Inc.
b. Starter Trac STDE - with drip edge by Plastic Components, Inc.
c. Universal Starter Track by Wind-lock Corporation
d. Sloped Starter Strip with Drip by Vinyl Corp.
2. Dryvit Drainage StripTM' (Optional - not required when Drainage Track is specified): A corrugated plastic material, which
provides drainage. Required when using Tyvek StuccoWrap without the Drainage Track.
E. Drainage Medium Options
1. Dryvit Drainage Mat [System 1(optional when Outsulation SMD System is installed over Tyvek StuccoWrap)]: A blue,
3.2 mm (1 /8 in) thick mat composed of open weave polymer threads.
2. Dryvit MD Spacer (optional when installed over Tyvek StuccoWrap): A 3.2 mm (1/8 in) thick polyethylene spacer, which
separates the insulation board from the substrate
F. Insulation Board: Quik-R Wall Insulation or Atlas Stucco Shield.
1. Thickness of insulation board shall be minimum 15.9 mm (5/8 in).
2. The insulation board shall be manufactured by Dow Chemical Corporation or Atlas Roofing Corporation.
G. Mechanical Fasteners consist of a 44 mm (1 '/. in) diameter polypropylene plastic plate (washer) with key openings for
base coat penetration used in conjunction with a corrosion resistant fastener.
1. Washer
a. Shall be Wind-Lock ULP 302 or 402 Plate, or ITW Buildex Grid-MateT"" washer or Grid-Mate with stem.
2. Screws, Nails, Anchors
a. Wood/Steel Framing with a nailable substrate (Plywood or Oriented Strand Board).
1) Shall be minimum No. 6, bugle head corrosion resistant screws.
2) The screws shall be of sufficient length to penetrate the wood substrate a minimum of 19 mm (3/4 in).
3) Nails shall be minimum 12 gauge (8d), rinct shank. They shall be hot dipped galvanized and of sufficient length
to penetrate the structural base a minimum of 25 mm (1 in). Ring shank nails are not recommended for
attachment to Oriented Strand Board.
b. Wood/Steel Framing with a non-structural substrate (gypsum based or similar)
1) Wood Screws shall be a minimum No. 6, bugle head, corrosion resistant screws and of sufficient length to
penetrate the wood framinq a minimum of 19 mm (3/4 in).
2) Light Gauge Metal Framing (minimum 20 gauge) requires minimum No. 6, self drilling corrosion resistant screws
and shall be of su�cient length to penetrate the steel framinq a minimum of 9.5 mm (3/8 in).
3) Nails shall be rinq shank and a minimum of 12 gauge (8d). They shall be hot dipped galvanized and of
sufficient length to penetrate the wood framinq a minimum of 25 mm (1 in).
c. Concrete/Masonry
1) Anchors shall be a minimum 4.8 mm (3/16 in) diameter and corrosion resistant.
2) Anchors shall be of sufficient length to penetrate the substrate a minimum of 25 mm (1 inj.
3) Pullout values shall be substantiated for the particular substrate and fastener.
H. Insulation Board used for Foam Shapes (where specified): Expanded Polystyrene meeting the Dryvit Specification for
Insulation Board, DS131, and the following requirements:
1. The insulation board shall be manufactured by a board supplier listed by Dryvit Systems, Inc.
I. Base Coat: Shall be compatible with the insulation board and reinforcing mesh.
1. Cementitious: A liquid polymer-based matenal, which is field mixed with Portland cement.
a. Shall be Genesis
2. Ready mixed: A dry blend cementitious, copolymer-based product, field mixed with water.
a. Shall be Genesis� DM
J. Reinforcing Mesh: A balanced, open weave, glass fiber fabric treated for compatibility with other system materials.
NOTE: Reinforcing meshes are classified by impact resistance and specifed by weight and tensile strength as
listed in Section 1.04.D.1.a.4).
K. Finish: Shall be the type, color and texture as selected by the architecUowner and shall be one or more of the following:
1. Standard DPR (Dirt Pickup Resistance): Water-based, acrylic finish with integrat color and texture and formulated with
DPR chemistry:
a. Quarzputz� DPR: Open-texture pattem.
b. Sandblast� DPR: Medium texture.
c. Freestyle� DPR: Fine texture.
Outsulation SMD System (formerly Sprint MD System) Specification DS158
d. Sandpebble� DPR: Pebble te�ure.
e. Sandpebble� Fine DPR: Fine pebble te�ure.
2. E: Water-based, lightweight acrylic finish with integral color and teuture and formulated with DPR chemistry:
a. Quarzputz� E
b. Sandpebble� E
c. Sandpebble� Fine E
3. Specia�ty: Factory mixed, water-based acrylic
a. Ameristone: Multi-colored quartz aggregate with a flamed granite appearance.
b. Stone Mist°: Ceramicaliy colored quartz aggregate.
c. Custom Brick Finish: Acrylic polymer-based finish used in conjunction with a proprietary template system to
create the look of stone, brick, slate or tile.
d. TerraNeo : 100% acrylic-based finish with large mica chips and multi-colored quartz aggregates.
e. LymestoneT'": A premixed, 100% acrylic-based finish designed to replicate the appearance of limestone blocks.
4. Elastomeric DPR (Dih Pickup Resistance): Water-based, elastomeric acrylic finish with integral color and texture, and
formulated with DPR chemistry:
a. Weatherlastic Quarzputz
b. Weatherlastic Sandpebble
c. Weatherlastic� Sandpebble Fine
d. Weatherlastic� Adobe
5. Medallion Series PMR (Proven Mildew Resistance): Water-based, acrylic finish with integral color and texture and
formulated with PMR chemistry:
a. Quarzputz° PMR
b. Sandblast�PMR
c. Freestyle PMR
d. Sandpebble PMR
e. Sandpebble Fine PMR
6. Coatings, Primers and Sealers:
a. Demandit
b. Weatherlastic Smooth
c. Tuscan GlazeTM'
d. Revyvit
e. Color Prime
f. Prymit�
g. SealClear
PART III - EXECUTION
3.01 EXAMINATION
A. Prior to installation of the Outsulation SMD System, the contractor shall verify that the substrate:
1. Is of a type listed in Section 1.04 C.1.
2. Is flat within 6.4 mm (1/4 in) in a 1.2 m(4 ft) radius.
3. Is sound, dry, clean, free of efflorescence, connections are tight, has no surface voids, projections, or other conditions
that may interfere with the Outsulation SMD System installation or performance.
B. Prior to installation of the Outsulation SMD System, the architect or general contractor shall ensure that all needed
flashings and other waterproofing details have been completed, if such completion is required prior to the Outsulation
SMD System application. Additionally the contractor shall ensure that:
1. Metal roof flashing has been installed in accordance with Asphalt Roofing Manufacturers Association (ARMA)
Standards and Dryvit Outsulation SMD System Installation Details, DS163, or as otherwise necessary.
2. Openings are flashed in accordance with the Outsulation SMD System Installation Details, DS163, or as otherwise
necessary to prevent water penetration.
3. Chimneys, Balconies, and Decks have been properly flashed.
4. Windows, Doors, etc. are installed and flashed per manufacturer's requirements and the Outsulation SMD System
Installation Details, DS163.
5. Sheet type membrane water-resistive barriers have been installed in a weatherboard fashion in accordance with
building code and manufacturer's requirements.
C. Prior to the installation of the Outsulation SMD System, the contractor shall notify the general contractor and/or architect
and/or owner of all discrepancies.
3.02 PREPARATION
A. The Dryvit Outsulation SMD System materials shall be protected by permanent or temporary means from inclement
weather and other sources of damage prior to, during, and following application until completely dry.
B. Protect adjoining work and property during Outsulation SMD System installation.
C. When Dryvit Backstop NT is specified as the water-resistive barrier, the substrate shall be prepared as to be free of
foreign materials such as oil, dust, dirt, form release agents, efflorescence, paint, wax, water repellants, moisture, frost,
and any other condition that may inhibit adhesion.
10
Outsulation SMD System (formerly Sprint MD System) Specification DS158
3.03 INSTALLATION
A. The system shall be installed in accordance with the Dryvit Outsulation SMD System Application Instructions, DS123.
B. The overall minimum base coat thickness shall be sufficient to fully embed the mesh. The recommended method is to
apply the base coat in two (2) passes.
C. Sealant shall not be applied to textured finishes or base coat surfaces. Dryvit Outsulation SMD System surfaces in
contact with sealant shall be coated with Demandit or Color Prime.
D. High impact meshes shall be installed as specified at ground level, high tra�c areas and other areas exposed to or
susceptible to impact damage.
3.04 FIELD QUALITY CONTROL
A. The contractor shall be responsible for the proper application of the Outsulation SMD System materials.
B. Dryvit assumes no responsibility for on-site inspections or application of its products.
C. If required, the contractor shall certify in writing the quality of work perFormed relative to the substrate system, details,
installation procedures, workmanship and the specific products used.
D. If required, the sealant contractor shall certify in writing that the sealant application is in accordance with the sealant
manufacturer's and DryviYs recommendations.
3.05 CLEANING
A. All excess Outsu�ation SMD System materials shall be removed from the job site by the contractor in accordance with
contract provisions and as required by applicable �aw.
B. All surrounding areas, where the Dryvit Outsulation SMD System has been applied, shall be left free of debris and foreign
substances resulting from the contractor's work.
3.06 PROTECTION
A. The Outsulation SMD System shall be protected from inclement weather and other sources of damage until dry and
permanent protection in the form of flashings, sealants, etc. are installed.
Dryvit Systems, Inc.
P.O. Box 1014
One Energy Way
West Warvvick, RI 02893
800-556-7752
www.dryvit.com
Printed in USA R12:02-10-09 11
�DryvR Systems, Inc 1996
c�
dr vi �
_y
��, � cnr-�oa-�.
--- - - -. _ � _ I
___-- - --
—�_ _ -
OSMD 0.0.01
WOOD OR STEEL FRAMING
�SUBSTRATE
CODE APPROVED WATER-RESISTIVE BARRIER
DRYVIT MD SPACEI�"
DRYVIT APPROVEO WASHER WITH
CORROSION RESISTANT FASTENER
APPROVED OSMD SYSTEM INSULATION BOARD
'IT GENESISm, GENESIS DM
_NESIS DMS BASE COAT
IT REINFORCING MESH
IT GENESIS, GENESIS DM
=NESIS DMS BASE COAT
IT FINISH
IAGE STRIP
DRYVIT DETAIL
> 51 MM (2") MIN.
,CKSIDE OF INSULATION BOARD
Dralnage Traek
Option
Outsulation°SMD SySt@1'1'1� Outsulation SMD System
/WPROVEO BY: REV: DATE:
RS l 02/09
The architecture, engineenng and desgn of the project using the
Dryvi[ products is ihe responsAility o/ the project's design
pro(essional. All systems must comply with bcal W ilding codes arW
standards. This detail is for general informatian arW guidance only
a�d Dryvit specificaRy disclaims any Kabiiry for �he use of
fhis detail and for ihe arrhi[acture, design, engineering or wakmanship
of any prqec[. The projec[ design prdessional deterrrtines, in i[s sde
disaetion, wheMer this detail w a W nclionaqy equivalenc al[emative
't^+ bes[ suked (or Ihe projec[. Use of a fu�ctiona�y equivelent detai
does rqt �ridate Dryvit's wartanty. Th's detail is subjec! to change
withou[ notice. Contact Dryvi[ In insure you have Ihe mosl rxen�
version.
• OR
dr vi
y
Outsulation0 SMD SystemTM
(formerly Sprint MD System0)
Exterior Cladding With Moisture Drainage
Stopping Moisture in its Tracks
For residential and light commercial construction, the Dryvit
Outsulation SMD System offers outstanding insulating qualities
and versatile beauty with an extra level of moisture protection.
The drainage plane installed between the water-resistive barrier
and the insulation board creates a drainage channel to weep
incidental water to the exterior.
DS441
tnglneered for Moisture Drainage
The system's insulation board is mechanically fastened over a code-approved water-resistive
barrier over plywood or OSB substrate with Dryvit's approved fasteners, which provide
maximum wind load performance. The drainage plane creates a path, which allows for a
quick exit of incidental moisture.
A Transferable 10-Year Drainage and Materials Warranty--An Industry First
The Outsulation SMD System is backed by an unprecedented ten-year moisture drainage
and materials warranty — an industry first. This unique assurance gives you an added level of
confidence. The system is warranted to effectively drain any moisture that enters the wall
between the insulation board and the water-resistive barrier. This innovative warranty also
has another important benefit: it is transferable from the builder to the owner, and subsequent
owners, during the covered ten-year period.
Fast Installation, Perfect for Remodeling
The system's large dimension insulation board (4 ft x 8 ft) reduces the total number of joints
and promotes faster and easier installation.
Dryvit Energy Efficiency, Durability and Beauty
The Outsutation SMD System maintains the tradition of Dryvit's leadership in design flexibility,
thermal efficiency (R-value 5.6 per inch thickness), impact resistance and superior finishes
with proven resistance to dirt and mildew accumulation. All Dryvit finishes, in their wide
variety of colors and textures, can be applied to the Outsulation SMD System. Dryvit
finishes, as with all other exteriors, are designed to require normal maintenance (refer to
DryviYs Homeowner's Maintenance Guide, DS235, or the Cleaning and Recoating data
sheet, DS152).
Dryvit Systems, Inc.
One Energy Way
P.O. Box 1014
West Warvvick, RI 02893
800-556-7752
www.dryvit.com
Printed in USA R4:01-13-09
OODryvit Systems, Inc. 1998
Informatlon contained in this infortnation page conforms to the
standard detail recommendations and specifications for the
installation of Dryvit Systems, Inc. products as of the date of
publication of this document and is presented in good faith.
Dryvit Systems, Inc. assumes no liability, expressed or
implied, as to the architecture, engineering or workmanship of
any project. To ensure that you are using the latest, most
complete information, contact Dryvit Systems, Inc.
� �
dr vi �
_y-
��
(°1')TOWN OF VAIL
75 South Frontage Road West Community Development Department
Vail. Colorado 81657 970.479.2138
vailgov.com 970.479.2452 fax
Certificate
of
Non-Compliance
02/06/2015
Daniel Braun
300 W.8'h ST. unit 417
Vancouver .WA. 98660-3440
Dear Owner/Agent,
A certificate of non-compliance is hereby filed in the Town of Vail
permanent records for the property located at with the following
action:
On 08/27/2012 permit B12-0390 was applied for at this office for exterior renovations. This
permit has expired per section 105.5 of the International Building Code 2012 edition. The Town
of Vail cannot verify code compliance and the structure has not received a final approval for
work authorized. A hold on the approval of any future projects for this property is hereby ordered
until the aforementioned permit is resolved with this office.
Sincer: y,
Ma in -. aeberle
C ief Building Official