Loading...
The URL can be used to link to this page
Your browser does not support the video tag.
Home
My WebLink
About
F12-0041 approved calcs
RAPID RESPONSE Series LFII Residential Sprinklers 4.9 K-factor Flat-Plate Concealed Pendent Wet Pipe and Dry Pipe Systems Technical Services 800-381-9312 +1-401-781-8220 www.tyco-fi re.com Page 1 of 6 APRIL 2012 TFP443 General Description The TYCO RAPID RESPONSE Series LFII Residential Flat-Plate Concealed Pendent Sprinklers (TY2524) are decora- tive, fast response, fusible solder sprin- klers designed for use in residential oc- cupancies such as homes, apartments, dormitories, and hotels. The Cover Plate/Retainer Assembly con- ceals the sprinkler operating compo- nents above the ceiling. The fl at profi le of the Cover Plate provides the optimum aesthetically appealing sprinkler design. Additionally, the concealed design of the Series LFII Residential Flat-Plate Con- cealed Pendent Sprinklers provides 1/2 inch (12,8 mm) vertical adjustment. This adjustment provides a measure of fl ex- ibility when cutting fi xed sprinkler drops. The Series LFII Residential Flat-Plate Concealed Pendent Sprinklers are in- tended for use in the following systems: • wet and dry pipe residential sprin- kler systems for one- and two-fam- ily dwellings and mobile homes per NFPA 13D • wet and dry pipe residential sprin- kler systems for residential occu- pancies up to and including four sto- ries in height per NFPA 13R • wet and dry pipe sprinkler systems for the residential portions of any occupancy per NFPA 13. The Series LFII Residential Sprinklers have been designed with heat sensitiv- ity and water distribution characteristics proven to help in the control of residen- tial fi res and to improve the chance for occupants to escape or be evacuated. The Series LFII Residential Flat-Plate Concealed Pendent Sprinklers are shipped with a Disposable Protective Cap. The Protective Cap protects the sprinkler during ceiling installation or fi nish. After ceiling installation is com- plete, the Protective Cap is removed and the Cover Plate/Retainer Assem- bly is installed. Removing the Protec- tive Cap is required for proper sprinkler performance. Dry Pipe System Application The Series LFII Residential Flat-Plate Concealed Pendent Sprinkler offers a laboratory approved option for design- ing dry pipe residential sprinkler sys- tems, whereas, most residential sprin- klers are laboratory approved for wet systems only. Through extensive testing and as ref- erenced in U.S. Patent 7,712,543, it has been determined that the number of de- sign sprinklers (hydraulic design area) for the Series LFII Residential Flat-Plate Concealed Sprinklers (TY2524) need not be increased over the number of design sprinklers (hydraulic design area) speci- fi ed for wet pipe sprinkler systems, as is customary for density/area sprinkler systems designed per NFPA 13, 13D, or 13R. Consequently, the Series LFII Residen- tial Flat-Plate Concealed Sprinklers (TY2524) offer the features of non-wa- ter fi lled pipe in addition to not having to increase the number of design sprinklers (hydraulic design area) for systems de- signed to NFPA 13, 13D, or 13R. Non- water fi lled pipe will permit options for areas sensitive to freezing. NOTICE The Series LFII Residential Flat-Plate Concealed Pendent Sprinklers (TY2524) described herein must be installed and maintained in compliance with this doc- ument and the applicable standards of the National Fire Protection Association, in addition to the standards of any au- thorities having jurisdiction. Failure to do so may impair the performance of these devices. The owner is responsible for maintain- ing their fi re protection system and de- vices in proper operating condition. The installing contractor or sprinkler manu- facturer should be contacted with any questions. Sprinkler Identifi cation Number (SIN) TY2524 IMPORTANT Always refer to Technical Data Sheet TFP700 for the “INSTALLER WARNING” that provides cautions with respect to handling and instal- lation of sprinkler systems and com- ponents. Improper handling and in- stallation can permanently damage a sprinkler system or its components and cause the sprinkler to fail to operate in a fi re situation or cause it to operate prematurely. TFP443 Page 2 of 6 FIGURE 3 PROTECTIVE CAP AND ACTIVATED DEFLECTOR — INSTALLATION DIMENSIONS — FIGURE 1 RAPID RESPONSE SERIES LFII RESIDENTIAL FLAT-PLATE CONCEALED PENDENT SPRINKLER (TY2524) — ASSEMBLY — PLATE COVER EJECTION SPRING DIMPLES WITH THREAD RETAINER ASSEMBLY SEALING COMPRESSION SCREW POSITION) (OPERATED DEFLECTOR FLUSH WITH SURFACE IS SUPPORT CUP UNTIL MOUNTING THREAD INTO SOLDER TAB CEILING DEFLECTOR CAP (1/2" NPT) BODY AREA WRENCHING SPRINKLER SADDLE ROLL FORMED THREADS CUP WITH SUPPORT ELEMENT SOLDER LINK LEVER GUIDE PIN HOUSING GUIDE PIN SPRINKLER/SUPPORT CUP COVER PLATE/RETAINER ASSEMBLY ASSEMBLY (81,0 mm) 3-3/16" DIA. 1/2" NPT (63,5 mm) 2-1/2" DIA. MOUNTING SURFACE (4,8 mm) 3/16" 1/8" GAP (3,2 mm) FITTING SPRINKLER FACE OF 7/8" (22,2 mm) 1-1/8" (28,6 mm) TIPOPERATED POSITION DEFLECTOR IN 1/2" (12,7 mm) ADJUSTMENT THREADED SPRINKLER- SUPPORT CUP ASSEMBLY OPERATED SPRINKLER 1-7/8"±1/8" ±3,2 mm) (47,6 mm SPRINKLER- SUPPORT CUP ASSEMBLYASSEMBLY COVER- RETAINER COVER PLATE RETAINER DISPOSABLE PROTECTIVE CAP FIGURE 2 W-TYPE 18 — SPRINKLER WRENCH — RECESS WRENCH WITH SPRINKLER ENGAGEMENT IN TO ENSURE WRENCHING AREA PUSH WRENCH TFP443 Page 3 of 6 Technical Data Approvals UL and C-UL Listed The TYCO RAPID RESPONSE Series LFII Residential Flat-Plate Concealed Pendent Sprinklers are only listed with the Series LFII Concealed Cover Plates having a factory-applied fi nish. For details on approvals, refer to the De- sign Criteria section. Maximum Working Pressure 175 psi (12,1 bar) Discharge Coeffi cient K=4.9 GPM/psi1/2 (70,6 LPM/bar1/2) Temperature Rating Sprinkler: 160°F (71°C) Cover Plate: 139°F (59°C) Vertical Adjustment 1/2 inch (12,7 mm) Finishes Refer to the Ordering Procedure section. Physical Characteristics Cover Plate/Retainer Assembly: Cover Plate . . . . . . . . . . . . . Copper Ejection Spring . . . . Stainless Steel Retainer . . . . . . . . . . . . . . . . Brass Sprinkler/Support Cup Assembly: Body . . . . . . . . . . . . . . . . . . . Brass Cap . . . . . . . . . . . . . . . . . . . Bronze Saddle. . . . . . . . . . . . . . . . . . Brass Sealing Assembly . . . . . . .Beryllium Nickel w/ TEFLON Soldered Link Halves . . . . . . Nickel Lever . . . . . . . . . . . . . . . . . . Bronze Compression Screw . . . . . . . Brass Defl ector . . . . . . . . . . . . . . . Bronze Guide Pin Housing. . . . . . . . Bronze Guide Pins . . . . . . . . . . . . . Bronze Support Cup . . . . . . . . . . . . . . Steel Operation When exposed to heat from a fi re, the Cover Plate, which is normally soldered to the Retainer at three points, falls away to expose the Sprinkler/Support Cup As- sembly. At this point, the Defl ector, sup- ported by the Guide Pins, drops down to its operated position. The Solder Link Element of the Sprinkler/ Support Cup Assembly is comprised of two link halves that are soldered togeth- er with a thin layer of solder. When the rated temperature is reached, the sol- der melts and the two link halves sepa- rate, allowing the sprinkler to activate and fl ow water. Design Criteria The TYCO RAPID RESPONSE Series LFII Residential Flat-Plate Concealed Pendent Sprinklers (TY2524) are UL and C-UL Listed for installation in ac- cordance with this section: Residential Sprinkler Design Guide When conditions exist that are outside the scope of the provided criteria, re- fer to the Residential Sprinkler Design Guide TFP490 for the manufacturer's recommendations that may be accept- able to the authority having jurisdiction. System Type Per the UL Listing, wet pipe and dry pipe systems may be utilized. Per the C-UL Listing, only wet pipe systems may be utilized. Refer to Technical Data Sheet TFP485 about the use of Residential Sprinklers in residential dry pipe systems. Hydraulic Design (NFPA 13D and 13R) For systems designed to NFPA 13D or NFPA 13R, the minimum required sprin- kler fl ow rate are given in Tables A and B as a function of temperature rating and the maximum allowable coverage areas. The sprinkler fl ow rate is the mini- mum required discharge from each of the total number of “design sprinklers” as specifi ed in NFPA 13D or NFPA 13R. The number of “design sprinklers” spec- ifi ed in NFPA 13D and 13R for wet pipe systems is to be applied when designing dry pipe systems. Hydraulic Design (NFPA 13) For systems designed to NFPA 13, the number of design sprinklers is to be the four most hydraulically demanding sprinklers. The minimum required dis- charge from each of the four sprinklers is to be the greater of the following: • The fl ow rates given in Tables A and B as a function of temperature rating and the maximum allowable cover- age area. • A minimum discharge of 0.1 gpm/ft2. over the “design area” comprised of the four most hydraulically demand- ing sprinklers for the actual coverage areas being protected by the four sprinklers. The number of “design sprinklers” specifi ed in NFPA 13 for wet pipe sys- tems is to be applied when designing dry pipe systems. Dry Pipe System Water Delivery When using the Series LFII Residential Flat-Plate Concealed Pendent Sprinklers (TY2524) in dry pipe sprinkler systems, the time for water delivery exceed 15 seconds for the most remote operat- ing sprinkler. Obstruction to Water Distribution. Sprinklers are to be located in accor- dance with the obstruction rules of NFPA 13D, 13R, and 13 as applicable for residential sprinklers as well as with the obstruction criteria described within the Technical Data Sheet TFP490. Operational Sensitivity Install sprinklers relative to the ceiling mounting surface as shown in Figure 3. The Series LFII Residential Flat-Plate Concealed Pendent Sprinklers must not be used in applications where the air pressure above the ceiling is greater than that below. Down drafts through the Support Cup can delay sprinkler op- eration in a fi re situation. Sprinkler Spacing The minimum spacing between sprin- klers is 8 feet (2,4 m). The maximum spacing between sprinklers cannot ex- ceed the length of the coverage area (Table A) being hydraulically calculated (e.g., a maximum of 12 feet for a 12 ft. x 12 ft. coverage area or 20 feet for a 20 ft. x 20 ft. coverage area.) TFP443 Page 4 of 6 Maximum Coverage Area (a) Ft. x Ft. (m x m) Maximum Spacing Ft. (m) DRY PIPE SYSTEM (b) Minimum Flow and Residual Pressure Horizontal Ceiling Minimum Flow and Residual Pressure (c) (Maximum 2 Inch Rise for 12 Inch Run) 160°F (71°C) Sprinkler 12 x 12 (3,7 x 3,7) 12 (3,7) 15 GPM (56,8 LPM) 9.4 psi (0,65 bar) 14 x 14 (4,3 x 4,3) 14 (4,3) 15 GPM (56,8 LPM) 9.4 psi (0,65 bar) 16 x 16 (4,9 x 4,9) 16 (4,9) 16 GPM (60,6 LPM) 10,7 psi (0,74 bar) 18 x 18 (5,5 x 5,5) 18 (5,5) 17 GPM (64,3 LPM) 12.0 psi (0,83 bar) 20 x 20 (6,1 x 6,1) 20 (6,1) 21 GPM (79,5 LPM) 18,4 psi (1,27 bar) (a) For coverage area dimensions less than or between those indicated, use the minimum required fl ow for the next highest coverage area for which Hydraulic Design section under the Design Criteria are stated. (b) The Minimum Flow requirement is based on minimum fl ow in GPM (LPM) from each sprinkler. The associated residual pressures are calculated using the nominal K-factor. Refer to “Hydraulic Design” in the Design Criteria section for details. (c) For NFPA 13 residential applications, the greater of 0.1 gpm/ft.2 over the design area or the fl ow in accordance with the criteria in this table must be used. TABLE B SERIES LFII RESIDENTIAL FLAT-PLATE CONCEALED PENDENT SPRINKLER (TY2524) NFPA 13D, 13R, AND 13 HYDRAULIC DESIGN CRITERIA — DRY PIPE SYSTEMS — Maximum Coverage Area (a) Ft. x Ft. (m x m) Maximum Spacing Ft. (m) WET PIPE SYSTEM (b) Minimum Flow and Residual Pressure Horizontal Ceiling (c, d, e) (Maximum 2 inch rise for 12 inch run) Sloped Ceiling(c, d, e) (Greater than 2 inch rise up to maximum 4 inch rise for 12 inch run) Sloped Ceiling(c, d, e) (Greater than 4 inch rise up to maximum 8 inch rise for 12 inch run) 160°F (71°C) Sprinkler 160°F (71°C) Sprinkler 160°F (71°C) Sprinkler 12 x 12 (3,7 x 3,7) 12 (3,7) 13 GPM (49,2 LPM) 7.0 psi (0,48 bar) 17 GPM (64,3 LPM) 12.0 psi (0,83 bar) 17 GPM (64,3 LPM) 12.0 psi (0,83 bar) 14 x 14 (4,3 x 4,3) 14 (4,3) 13 GPM (49,2 LPM) 7.0 psi (0,48 bar) 17 GPM (64,3 LPM) 12.0 psi (0,83 bar) 17 GPM (64,3 LPM) 12.0 psi (0,83 bar) 16 x 16 (4,9 x 4,9) 16 (4,9) 13 GPM (49,2 LPM) 7.0 psi (0,48 bar) 17 GPM (64,3 LPM) 12.0 psi (0,83 bar) 17 GPM (64,3 LPM) 12.0 psi (0,83 bar) 18 x 18 (5,5 x 5,5) 18 (5,5) 17 GPM (64,3 LPM) 12.0 psi (0,83 bar) 22 GPM (83,3 LPM) 20.2 psi (1,39 bar) 22 GPM (83,3 LPM) 20.2 psi (1,39 bar) 20 x 20 (6,1 x 6,1) 20 (6,1) 20 GPM (75,7 LPM) 16.7 psi (1,15 bar) 24 GPM (90,8 LPM) 24.0 psi (1,65 bar) 24 GPM (90,8 LPM) 24.0 psi (1,65 bar) (a) For coverage area dimensions less than or between those indicated, use the minimum required fl ow for the next highest coverage area for which Hydraulic Design section under the Design Criteria are stated. (b) The Minimum Flow requirement is based on minimum fl ow in GPM (LPM) from each sprinkler. The associated residual pressures are calculated using the nominal K-factor. Refer to “Hydraulic Design” in the Design Criteria section for details. (c) For NFPA 13D 2010 applications, Horizontal Ceiling criteria shall be used for certain sloped ceiling confi gurations up to 8:12 pitch. Refer to TIA 1028R for allowed sloped ceiling limitations when using horizontal ceiling criteria. (d) For NFPA 13R applications, Horizontal Ceiling criteria may be used for sloped ceiling confi gurations up to 8:12 pitch when acceptable to the local authority having jurisdiction. (e) For NFPA 13 residential applications, the greater of 0.1 gpm/ft.2 over the design area or the fl ow in accordance with the criteria in this table must be used. TABLE A SERIES LFII RESIDENTIAL FLAT-PLATE CONCEALED PENDENT SPRINKLER (TY2524) NFPA 13D, 13R, AND 13 HYDRAULIC DESIGN CRITERIA — WET PIPE SYSTEMS — TFP443 Page 5 of 6 Installation The TYCO RAPID RESPONSE Series LFII Residential Flat-Plate Concealed Pendent Sprinklers must be installed in accordance with this section: General Instructions Damage to the Solder Link Element dur- ing installation can be avoided by han- dling the sprinkler by the Support Cup only; that is, do not apply pressure to the Solder Link Element (Figure 1). A leak-tight 1/2 inch NPT sprinkler joint should be obtained by applying a min- imum-to-maximum torque of 7 to 14 ft.-lbs. (9,5 to 19,0 Nm). Higher levels of torque can distort the sprinkler inlet with consequent leakage or impairment of the sprinkler. Do not attempt to compensate for insuf- fi cient adjustment in the Cover Plate/ Retainer Assembly by under- or over- tightening the sprinkler. Re-adjust the position of the sprinkler fi tting to suit. Step 1. Install pendent sprinklers in the pendent position, with the center- line of the sprinkler perpendicular to the mounting surface. Step 2. Remove the Protective Cap. Step 3. With pipe-thread sealant ap- plied to the pipe threads, and using the W-Type 18 Wrench shown in Figure 2, install and tighten the Sprinkler/Sup- port Cup Assembly into the fi tting. The W-Type 18 Wrench accepts a 1/2 inch ratchet drive. Step 4. Replace the Protective Cap by pushing it upwards until it bottoms out against the Support Cup. The Protec- tive Cap helps prevent damage to the Defl ector and Guide Pins during ceiling installation and/or during application of the fi nish coating of the ceiling. NOTICE As long as the protective Cap remains in place, the system is considered “Out Of Service”. Step 5. After the ceiling has been com- pleted with the 2-1/2 inch (63 mm) diam- eter hole and in preparation for install- ing the Cover Plate/Retainer Assembly, remove and discard the Protective Cap, and verify that the Defl ector moves up and down freely. If the sprinkler has been damaged and the defl ector does not move up and down freely, replace the entire sprinkler assembly. Do not attempt to modify or repair a damaged sprinkler. Step 6. Screw on the Cover Plate/Re- tainer Assembly until its fl ange contacts the ceiling. Do not continue to screw on the Cover Plate/Retainer Assembly such that it lifts a ceiling panel out of its normal position. If the Cover Plate/Retainer Assembly cannot be engaged with the Mounting Cup or the Cover Plate/Retainer Assem- bly cannot be engaged suffi ciently to contact the ceiling, the Sprinkler Fitting must be repositioned. Care and Maintenance The TYCO RAPID RESPONSE Series LFII Residential Flat-Plate Concealed Pendent Sprinkler (TY2524) must be maintained and serviced in accordance with ths section: Before closing a fi re protection system main control valve for maintenance work on the fi re protection system that it con- trols, obtain permission to shut down the affected fi re protection system from the proper authorities and notify all person- nel who may be affected by this action. Absence of a Cover Plate may delay the sprinkler operation in a fi re situation. The owner must assure that the sprin- klers are not used for hanging any ob- jects and that the sprinklers are only cleaned by means of gently dusting with a feather duster; otherwise, non-opera- tion in the event of a fi re or inadvertent operation may result. When properly installed, there is a nomi- nal 1/8 inch (3,2 mm) air gap between the lip of the Cover Plate and the ceil- ing, as shown in Figure 3. This air gap is necessary for proper operation of the sprinkler by allowing heat fl ow from a fi re to pass below and above the Cover Plate to help assure appropriate release of the Cover Plate in a fi re situation. If the ceiling needs repainting after sprinkler installation, exercise care to ensure that the new paint does not seal off any of the air gap. Failure to do so may impair sprinkler operation. Factory painted Cover Plates must not be repainted. They should be replaced, if necessary, by factory painted units. Non-factory applied paint may adversely delay or prevent sprinkler operation in the event of a fi re. Do not pull the Cover Plate relative to the Retainer. Separation may result. Sprinklers which are found to be leaking or exhibiting visible signs of corrosion must be replaced. Automatic sprinklers must never be painted, plated, coated, or otherwise altered after leaving the factory. Modi- fi ed or overheated sprinklers must be replaced. Care must be exercised to avoid dam- age to the sprinklers - before, during, and after installation. Sprinklers dam- aged by dropping, striking, wrench twist/ slippage, or the like, must be replaced. The owner is responsible for the in- spection, testing, and maintenance of their fi re protection system and devices in compliance with this document, as well as with the applicable standards of the National Fire Protection Association (e.g., NFPA 25), in addition to the stan- dards of any other authorities having ju- risdiction. Contact the installing contrac- tor or sprinkler manufacturer regarding any questions. Automatic sprinkler systems are rec- ommended to be inspected, tested, and maintained by a qualifi ed Inspec- tion Service in accordance with local requirements and/or national codes. PRINTED IN USAMKT. #8800003 - REV AA MFG. #5400802 - 11/02 VSR-SF VANE TYPE WATERFLOW ALARM SWITCH WITH RETARD FOR SMALL PIPE PAGE 1 OF 2 UL, ULC, CSFM Listed and NYMEA Accepted, CE Marked Service Pressure: Up to 250 PSI (17,2 BAR) Minimum Flow Rate for Alarm: 8-10 GPM (30-38 LPM) Maximum Surge: 18 FPS (5,5 m/s) Enclosure: Die-cast, red enamel fi nish Cover held in place with tamper resistant screws Contact Ratings: Two sets of SPDT (Form C) 15.0 Amps at 125/250 VAC 2.0 Amps at 30 VDC Conduit Entrances: Two knockouts provided for 1/2" conduit. Usage: Listed plastic, copper and schedule 40 iron pipe. Fits pipe sizes - 1" (25mm), 1 1/4" (32mm), 1 1/2" (38mm) and 2" (50mm) Note: 12 paddles are furnished with each unit, one for each pipe size of threaded and sweat TEE, one for 1" (25mm) CPVC, one for 1" (25mm) CPVC (Central), one for 1 1/2" (38mm) polybutylene and one for 1 1/2" (38mm) threaded (Japan). (CTS-Copper tubing size) Environmental Specifi cations: • Suitable for indoor or outdoor use with factory installed gasket and die-cast housing. • NEMA 4/IP55 rated enclosure - use with appropriate conduit fi tting. • Temperature range: 40° F to 120° F, 4,5° C to 49° C) Caution: This device is not intended for applications in explosive environments. Service Use: Automatic Sprinkler NFPA-13 One or two family dwelling NFPA-13D Residential occupancy up to four stories NFPA-13R National Fire Alarm Code NFPA-72 Optional: Cover Tamper Switch Kit, Stock No. 0090018 Stock No. 1113000 U.S. Pat. No. 3921989, Canadian Pat. No. 1009680 Other Patents Pending The Model VSR-SF is a vane type waterfl ow switch for use on wet sprinkler systems that use 1" (25mm), 1 1/4" (32mm), 1 1/2" (38mm) or 2" (50mm) pipe size. The unit may also be used as a sectional waterfl ow detector on large systems. The unit contains two single pole double throw snap action switches and an adjustable, instantly recycling pneumatic retard. The switches are actuated when a fl ow of 8-10 gallons per minute (30-38 LPM) or more occurs downstream of the device. The fl ow condition must exist for a period of time necessary to overcome the selected retard period. INSTALLATION: These devices may be mounted in horizontal or vertical pipe. On horizontal pipe they should be installed on the top side of the pipe where they will be accessible. The units should not be installed within 6" (15cm) of a valve, drain or fi tting which changes the direction of the waterfl ow. Select the proper paddle for the pipe size and type of TEE used see Fig. 1 for instructions on changing paddle. The unit has a 1" NPT bushing for threading into a non-corrosive TEE. See Fig. 2 for proper TEE size, type and installation. Use no more than three wraps of tefl on tape. Screw the device into the TEE fi tting as shown in Fig. 2. Care must be taken to properly orient the device for the direction of waterfl ow. The vane must not rub the inside of the TEE or bind in any way. The stem should move freely when operated by hand. The device can also be used in copper or plastic pipe installations with the proper adapters so that the specifi ed TEE fi tting may be installed on the pipe run. INSPECTION AND TESTING: Check the operation of the unit by opening the inspector’s test valve at the end of the sprinkler line or the drain and test connection, if an inspector’s test valve is not provided. If there are no provisions for testing the operation of the fl ow detection device on the system, application of the VSR-SF is not recommended or advisable The frequency of the inspection and testing and its associated protective monitoring system should be in accordance with the applicable NFPA Codes and Standards and/or authority having jurisdiction (manufacturer recommends quarterly or more frequently). Potter Electric Signal Company • 2081 Craig Road, St. Louis, MO, 63146-4161 • Phone: 800-325-3936/Canada 888-882-1833 • www.pottersignal.com PRINTED IN USAMKT. #8800003 - REV AA MFG. #5400802 - 11/02 VSR-SF VANE TYPE WATERFLOW ALARM SWITCH WITH RETARD FOR SMALL PIPE PAGE 2 OF 2 1 11/16” (4,3MM)APPROX. DEPTH DWG# 735-33 CAUTION: An uninsulated section of a single conductor should not be looped around the terminal and serve as two separate connections. The wire must be severed, thereby providing supervision of the connection in the event that the wire becomes dislodged from under the terminal. FIG. 1 Important: There are 12 paddles furnished with each unit. One for each size of threaded, sweat or plastic TEE as described in Fig. 2. These paddles have raised lettering that shows the pipe size and type of TEE that they are to be used with. The proper paddle must be used. The paddle must be properly attached (see drawing) and the screw that holds the paddle must be securely tightened. FIG. 2 NOTES: 1. The model VSR-SF has two switches, one can be used to operate a central station, proprietary or remote signaling unit, while the other is used to operate a local audible or visual annunciator. 2. For supervised circuits see “Switch Terminal Connections” drawing and caution note (Fig. 3). FIG. 4 TYPICAL ELECTRICAL CONNECTIONS Retard Adjustment: To change time, turn knob (either direction) for desired time delay. Use the minimum amount of retard necessary to prevent false alarms. A “B” setting is usually adequate for this. Factory set at “B”. FIG. 3 SWITCH TERMINAL CONNECTIONS CLAMPING PLATE TERMINAL OUT G O I N G INC O M I NG DWG# 923-3 FIG. 5 To remove knockouts: Place screwdriver at edge of knockouts, not in the center. APPLICATION WARNING! Due to the possibility of unintended discharges caused by pressure surges, trapped air, or short retard times, waterfl ow switches that are monitoring wet pipe sprinkler systems should not be used as the sole initiating device to discharge AFFF, deluge, or chemical suppression systems. Screw the device into the tee fi tting as shown. Care must be taken to properly orient the device for the direction of waterfl ow. On sweat tees, no threaded bushings, inserts, or adapters are permitted, unless they comply with the dimensions listed in the chart below. Important - The depth to the inside bottom of the tee should have the following dimensions: DIRECTION OF WATER FLOW DWG# 737-31 2 SETS OF NORMALLY OPEN CONTACTS CLOSE ON ALARM THE N.C. AND N.O. MARKINGS ON THE SWITCH ARE FOR AN ALARM CONDITION. THE CONTACTS ARE REVERSED WHEN THE DEVICE IS IN THE NORMAL CONDITION. WATERFLOW ZONE ON FIRE PANEL EOLR FROM FIRE PANEL POSITIVE DC OR HOT AC NEGATIVE DC OR NEUTRAL AC DWG# 761-2 BELL COM NONC COM NONC COM NONC COM NONC EOLR Warning: Do not use more than three wraps of tefl on tape. Shown with optional Cover Tamper Switch Kit. General Description Tyco®CPVCPipeandFittingspro- ducedbyTycoFire&BuildingProd- ucts(TFBP)aredesignedexclusively foruseinwetpipeautomaticfiresprin- klersystems.TheTycoCPVCPipe andFittingsareproducedfromBlaze- Master®CPVCcompoundthatisa speciallydevelopedthermoplastic compoundcomposedofpostchlorin- atedpolyvinylchloride(CPVC)resin andstateoftheartadditives.Tyco CPVCPipeandFittingsareeasierto installthantraditionalsteelpipesys- tems,andatthesametime,provide superiorheatresistanceandstrength ascomparedtotraditionalCPVCand PVCpipingmaterialsusedinthe plumbingtrade.Variousadaptersare availabletoconnectCPVCpipetome- tallicpiping.Allfemalepipethread adaptershavebrassinsertsfordura- bility.Groovedadaptersconnectdi- rectlytogroovedendvalvesandme- tallicpipe,withflexiblegroovedend couplings. NOTICE Tyco®CPVCPipeandFittingspro- ducedwithBlazeMaster®CPVCcom- pounddescribedhereinmustbein- stalledandmaintainedincompliance withthisdocumentandwiththeappli- cablestandardsoftheNationalFire ProtectionAssociation,inadditionto thestandardsofanyauthoritieshaving jurisdiction.Failuretodosomayim- pairtheperformanceofthesedevices. Theownerisresponsibleformaintain- ingtheirfireprotectionsystemandde- vicesinproperoperatingcondition. Theinstallingcontractororsprinkler manufacturershouldbecontacted withanyquestions. Technical Data Sizes 3/4"to3" MaximumWorkingPressure 175psi Approvals UL,FM,C-UL,NSF,LPCB,MEA,and theCityofLosAngeles.(RefertoIn- stallationHandbookIH-1900dated June2008forexactlisting/approval information.) ManufactureSource U.S.A. Material •Pipe:ASTMF442,SDR13.5 •Fittings:ASTMF438(Sch.40)and ASTMF439(Sch.80),ASTMF1970 Color Orange BlazeMaster ® CPVCFireSprinklerPipe&Fittings SubmittalSheet Page1of2 TFP1915JUNE,2008 TechnicalServices:Tel:(800)381-9312/Fax:(800)791-5500 BlazeMaster®isaregisteredtrademark ofTheLubrizolCorporation Installation Tyco®CPVCPipeandFittingspro- ducedbyTycoFire&BuildingProd- ucts(TFBP)aretobeinstalledin accordancewithInstallationHand- bookIH-1900datedJune2008. Careand Maintenance Theownerisresponsibleforthein- spection,testing,andmaintenanceof theirfireprotectionsystemandde- vicesincompliancewiththisdocu- ment,aswellaswiththeapplicable standardsoftheNationalFireProtec- tionAssociation(e.g.,NFPA25),in additiontothestandardsofany authorityhavingjurisdiction.Thein- stallingcontractororproductmanufac- turershouldbecontactedrelativeto anyquestions. Automaticsprinklersystemsshouldbe inspected,tested,andmaintainedbya qualifiedInspectionServiceinaccord- ancewithlocalrequirementsand/or nationalcodes. NOTICE Beforeclosingafireprotectionsystem controlvalveforinspectionormainte- nanceworkonthefireprotectionsys- temthatitcontrols,permissiontoshut downtheaffectedfireprotectionsys- temmustfirstbeobtainedfromthe properauthoritiesandallpersonnel whomaybeaffectedbythisaction mustbenotified. Afterplacingafireprotectionsystem inservice,notifytheproperauthorities andadvisethoseresponsibleformoni- toringproprietaryand/orcentralsta- tionalarms. Limited Warranty ProductsmanufacturedbyTycoFire& BuildingProducts(TFBP)arewar- rantedsolelytotheoriginalBuyerfor ten(10)yearsagainstdefectsinmate- rialandworkmanshipwhenpaidfor andproperlyinstalledandmaintained undernormaluseandservice.This warrantywillexpireten(10)years fromdateofshipmentbyTFBP.No warrantyisgivenforproductsorcom- ponentsmanufacturedbycompanies notaffiliatedbyownershipwithTFBP orforproductsandcomponentswhich havebeensubjecttomisuse,improper installation,corrosion,orwhichhave notbeeninstalled,maintained,modi- fiedorrepairedinaccordancewithap- plicableStandardsoftheNationalFire ProtectionAssociation,and/orthe standardsofanyotherAuthorities HavingJurisdiction.Materialsfound byTFBPtobedefectiveshallbeeither repairedorreplaced,atTFBP’ssole option.TFBPneitherassumes,nor authorizesanypersontoassumeforit, anyotherobligationinconnectionwith thesaleofproductsorpartsofprod- ucts.TFBPshallnotberesponsiblefor sprinklersystemdesignerrorsorinac- curateorincompleteinformationsup- pliedbyBuyerorBuyer’srepre- sentatives. InnoeventshallTFBPbeliable,in contract,tort,strictliabilityorunder anyotherlegaltheory,forincidental, indirect,specialorconsequentialdam- ages,includingbutnotlimitedtolabor charges,regardlessofwhetherTFBP wasinformedaboutthepossibilityof suchdamages,andinnoeventshall TFBP’sliabilityexceedanamount equaltothesalesprice. Theforegoingwarrantyismadeinlieu ofanyandallotherwarranties,ex- pressorimplied,includingwarranties ofmerchantabilityandfitnessforapar- ticularpurpose. Thislimitedwarrantysetsforththeex- clusiveremedyforclaimsbasedon failureofordefectinproducts,materi- alsorcomponents,whethertheclaim ismadeincontract,tort,strictliability oranyotherlegaltheory. Thiswarrantywillapplytothefullex- tentpermittedbylaw.Theinvalidity,in wholeorpart,ofanyportionofthis warrantywillnotaffecttheremainder. Page2of2 TFP1915 ©2008TYCOFIRE&BUILDINGPRODUCTS,451NorthCannonAvenue,Lansdale,Pennsylvania19446 Grinnell Grooved Fire Protection Products Grooved Fittings Technical Services: Tel: (800) 381-9312 / Fax: (800) 791-5500 www.tyco-fire.com September 2004 TFP1810Page 1 of 6 The grooved fittings provide an economical and efficient method of changing direction, adding an outlet, reducing, or capping grooved piping systems. Grooved fittings are available in durable ductile iron or fabricated steel as indicated. Note: Figure 510S and 519S fittings are special short radius fittings with smaller center to end dimensions than standard grooved fittings. Depending on the size and coupling used, there may be interferences at the bolt pads that require repositioning of the coupling orientation. The use of flange adapters is not recommended with Figures 510S and 519S fittings. Contact Tyco Fire Products for details. WARNING The Fittings described herein must be installed and maintained in compliance with this document, as well as with the applicable standards of the National Fire Protection Association, in addition to the standards of any other authorities having jurisdiction. Failure to do so may impair the performance of this device. The owner is responsible for maintaining their fire protection system and devices in proper operating condition. The installing contractor or sprinkler manufacturer should be contacted with any questions. Approvals: UL, FM, ULC, VdS, and LPCB; Note: See Fire Protection Submittal Sheet for exact Listing / Approval information. General Description When placing an order, indicate the full product name. Please specify the quantity, figure number, wall thickness, and size. Grinnell Grooved Piping Products, valves, accessories and other products are available throughout the U.S., Canada, and internationally, through a network of distribution centers. You may write directly or call 215-362-0700 for the distributor nearest you. Ordering Procedure Care and Maintenance The owner is responsible for the inspection, testing, and maintenance of their fire protection system and devices in accordance with the applicable standards of the National Fire Protection Association (e.g., NFPA 25), in addition to the standards of any authority having jurisdiction. The installing contractor or product manufacturer should be contacted relative to any questions. Any impairment must be immediately corrected. It is recommended that automatic sprinkler systems be inspected, tested, and maintained by a qualified Inspection Service. Products manufactured by Tyco Fire Products are warranted solely to the original Buyer for ten (10) years against defects in material and workmanship when paid for and properly installed and maintained under normal use and service. This warranty will expire ten (10) years from date of shipment by Tyco Fire Products. No warranty is given for products or components manufactured by companies not affiliated by ownership with Tyco Fire Products or for products and components which have been subject to misuse, improper installation, corrosion, or which have not been installed, maintained, modified or repaired in accordance with applicable Standards of the National Fire Protection Association (NFPA), and/or the standards of any other Authorities Having Jurisdiction. Materials found by Tyco Fire Products to be defective shall be either repaired or replaced, at Tyco Fire Products’ sole option. Tyco Fire Products neither assumes, nor authorizes any person to assume for it, any other obligation in connection with the sale of products or parts of products. Tyco Fire Products shall not be responsible for sprinkler system design errors or inaccurate or incomplete information supplied by Buyer or Buyer’s representatives. IN NO EVENT SHALL TYCO FIRE PRODUCTS BE LIABLE, IN CONTRACT, TORT, STRICT LIABILITY OR UNDER ANY OTHER LEGAL THEORY, FOR INCIDENTAL, INDIRECT, SPECIAL OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO LABOR CHARGES, REGARDLESS OF WHETHER TYCO FIRE PRODUCTS WAS INFORMED ABOUT THE POSSIBILITY OF SUCH DAMAGES, AND IN NO EVENT SHALL TYCO FIRE PRODUCTS’ LIABILITY EXCEED AN AMOUNT EQUAL TO THE SALES PRICE. THE FOREGOING WARRANTY IS MADE IN LIEU OF ANY AND ALL OTHER WARRANTIES EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Limited Wa rranty See Fire Protection Submittal Sheet for Pressure Rating and Listing/Approval Information LPCB Vd S Material: Cast: Figures: 201, 210, 219, 250, 260, 501, 510, 519, 510DE, 501S, 510S and 519S - Ductile iron conforming to ASTM A-536, Grade 65-45-12 Fabricated Steel: Figures 391, 392, 393, 312, 313, 321, 327, 341 and 350 - Carbon Steel, (Sizes 11/4" - 6" are Schedule 40); (Sizes 8" - 12" are Schedule 30), conforming to ASTM A-53 Grade B Protective Coatings: • Non-lead orange paint • Fire brigade red (optional) non-lead paint • Hot dipped galvanized conforming to ASTM A-153 Technical Data Page 2 of 6 TFP1810 ‡- Available with tapped plugs, contact Tyco Fire & Building Products. Figures 201, 210, 219, and 260 Figure 201Figure 210Figure 219Figure 260‡ 45° Elbow90° ElbowTee End Cap C to EAppx. Wt.C to EAppx. Wt.C to EAppx. Wt.E to EAppx. Wt. InchesLbs.InchesLbs.InchesLbs.InchesLbs. mmKg.mmKg.mmKg.mmKg. 1.750.92.751.02.751.40.880.4 44.50.469.90.569.90.622.40.2 1.751.12.751.22.751.80.880.6 44.50.569.90.569.90.822.40.3 2.001.83.252.03.252.70.880.9 50.80.882.60.982.61.222.40.4 2.252.23.753.03.755.80.880.9 57.21.095.31.495.32.622.40.4 2.252.23.753.03.755.80.941.1 57.21.095.31.495.32.623.90.5 2.503.54.254.54.257.00.881.1 63.51.6108.02.0108.03.222.40.5 2.885.54.758.54.7511.5 73.02.5120.73.9120.75.2 3.005.25.008.55.0011.81.002.6 76.22.4127.03.9127.05.425.41.2 3.257.75.2511.35.2510.6 82.63.5133.45.1133.44.8 3.257.75.5011.35.5015.30.924.7 82.63.5139.75.1139.76.923.42.1 3.258.55.5013.55.5017.01.005.0 82.63.9139.76.1139.77.725.42.3 3.5012.06.0014.66.0013.9 88.95.4152.46.6152.46.3 3.5012.06.5018.56.5026.01.007.5 88.95.4165.18.4165.111.825.43.4 3.5012.06.5018.56.5026.01.007.5 88.95.4165.18.4165.111.825.43.4 4.2523.07.7536.57.7545.0 108.010.4196.916.6196.920.4 4.2523.07.7536.57.7545.01.1912.8 108.010.4196.916.6196.920.430.25.8 4.7531.09.0060.09.0072.11.2520.0 120.714.1228.627.2228.632.731.89.1 5.2540.010.0067.010.0092.51.2536.0 133.418.1254.030.4254.042.031.816.3 Nominal Size 11/4" 11/2" 2" 21/2" 76.1mm 3" 108.0mm-- 4" 133.0mm-- 139.7mm 5" 159.0mm-- 165.1mm 6" 216.3mm-- 8" 10" 12" Friction Resistance* (Expressed as Equivalent Straight Pipe) ElbowTee Size90°45°BranchRun InchesFeetFeetFeetFeet mmMetersMetersMetersMeters 11⁄4 1.91.04.81.9 42.40.60.31.50.6 11⁄2 2.31.25.82.3 48.30.70.41.80.7 2 3.21.68.03.2 60.31.00.52.51.0 21⁄2 3.92.09.83.9 73.01.20.63.01.2 4.12.110.34.1 1.20.63.11.2 3 4.92.412.24.9 88.91.50.73.71.5 6.53.316.36.5 2.01.05.02.0 4 6.53.316.36.5 114.32.01.05.02.0 8.04.020.08.0 2.41.26.12.4 8.04.120.08.0 2.41.36.12.4 5 8.24.120.58.2 141.32.51.36.32.5 9.54.823.89.5 2.91.47.22.9 9.54.823.89.5 2.91.47.22.9 6 9.95.024.89.9 168.33.01.57.63.0 13.16.632.813.1 4.02.010.04.0 8 13.16.632.813.1 219.14.02.010.04.0 1016.58.341.316.5 273.05.02.512.65.0 1219.99.949.719.9 323.46.13.015.16.1 76.1mm 108.0mm 133.0mm 139.7mm 159.0mm 165.1mm 216.3mm Figure 260 E to E Figure 201 C to E C to E Figure 210 C to E C to E Figure 219 C to E C to E For reducing tees and branches, use the value that is corrosponding to the branch size. Example: for 8" x 8" x 2" tee, the branch value 2" is 8.0 feet. *Friction resistance for all elbows and tees except Figures 510S and 519S. Page 3 of 6 TFP1810 Figures 501S, 510S and 519S Figure 501SFigure 510S Figure 519S 45° Elbow90° ElbowTee C to EAppx Wt.C to EAppx. Wt.C to EAppx. Wt. InchesLbs.InchesLbs.InchesLbs. mmKg.mmKg.mmKg. 2.001.82.751.52.752.1 50.80.869.90.769.91.0 2.252.23.002.23.003.0 57.21.076.21.076.21.4 2.252.23.002.33.003.1 57.21.076.21.076.21.4 2.503.53.383.03.384.1 63.51.685.91.385.91.9 3.005.24.005.64.007.7 76.22.4101.62.6101.63.5 3.257.74.888.64.8812.0 82.63.5124.03.9124.05.4 3.258.54.888.84.8812.0 82.63.9124.03.9124.05.4 3.5012.05.5011.005.5015.0 88.95.4139.75.0139.76.8 3.5012.05.5011.25.5015.2 88.95.4139.75.1139.76.9 4.2523.06.8823.46.8831.2 108.010.4174.810.6174.814.2 Nominal Size 2" 21/2" 76.1mm 3" 4" 139.7mm 5" 165.1mm 6" 8" Figure 510S* C to E C to E Figure 519S* C to E C to E *Note: Figure 510S and 519S fittings are special short radius fittings with smaller center to end dimensions than standard grooved fittings. Depending on the size and coupling used, there may be interferences at the bolt pads which requires repositioning of the coupling orientation. The use of flange adapters is not recommended with Figures 510S and 519S fittings. Contact Tyco Fire Products for details. Figures 501, 510, 519 and 510DE Figure 501 C to E C to E Figure 510 C to E C to E Figure 501S C to E C to E Figure 510DE C to E C to E A B Figure 519 C to E C to E Figure 501Figure 510Figure 519 Figure 510DE 45° Elbow90° ElbowTee 90° Drain Elbow C to EAppx. Wt.C to EAppx. Wt.C to EAppx. Wt.C to EABAppx. Wt. InchesLbs.InchesLbs.InchesLbs.InchesInchesInchesLbs. mmKg.mmKg.mmKg.mmmmmmKg. 1.750.92.751.02.751.4 44.50.469.90.569.90.6 1.751.12.751.22.751.8 44.50.569.90.569.90.8 2.001.83.252.03.252.7 50.80.882.60.982.61.2 2.252.23.753.03.755.83.752.002.752.7 57.21.095.31.495.32.695.350.869.91.2 2.503.54.254.54.257.04.252.342.753.7 63.51.6108.02.0108.03.2108.059.469.91.7 3.005.25.008.55.0011.85.002.852.757.0 76.22.4127.03.9127.05.4127.072.469.93.2 3.258.55.5013.55.5017.05.503.382.7513.0 82.63.9139.76.1139.77.7139.785.969.95.9 3.5012.06.5018.56.5026.06.503.922.7513.4 88.95.4165.18.4165.111.8165.199.669.96.1 4.2523.07.7536.57.7545.07.754.952.7526.3 108.010.4196.916.6196.920.4196.9125.769.911.9 Nominal Size 11/4"---- 11/2"---- 2"---- 21/2" 3" 4" 5" 6" 8" Friction Resistance 501S, 510S & 519S (Expressed as Equivalent Straight Pipe) ElbowTee Size90°45°BranchRun InchesFeetFeetFeetFeet mmMetersMetersMetersMeters 2 3.21.68.03.2 60.31.00.52.51.0 21⁄2 3.92.09.83.9 73.01.20.63.01.2 4.12.110.34.1 1.20.63.11.2 3 4.92.412.24.9 88.91.50.73.71.5 4 6.53.316.36.5 114.32.01.05.02.0 8.04.120.08.0 2.41.36.12.4 5 8.24.120.58.2 141.32.51.36.32.5 9.54.823.89.5 2.91.47.22.9 6 9.95.024.89.9 168.33.01.57.63.0 8 13.16.632.813.1 219.14.02.010.04.0 76.1mm 139.7mm 165.1mm Page 4 of 6 TFP1810 Figures 250 and 350 Figure 350 Fabricated Sizes 3” to 6” E to E E to E Figure 350 Fabricated Sizes 8” to 12” E to E Figure 250 Cast Figures 250 and 350 Concentric Reducer - Groove x Groove NominalE to EAppx. Wt.NominalE to EAppx. Wt.NominalE to EAppx. Wt. SizeInchesLbs.SizeInchesLbs.SizeInchesLbs. InchesmmKg.InchesmmKg.InchesmmKg. 2.501.03.504.24.005.8 63.50.588.91.9101.62.6 2.501.33.504.45.0012.2 63.50.688.92.0127.05.5 2.501.23.504.65.0012.1 63.50.588.92.1127.05.5 2.501.53.504.65.0012.0 63.50.788.92.1127.05.5 2.501.63.504.55.0011.9 63.50.888.92.0127.05.4 2.501.33.504.45.0011.3 63.50.688.92.0127.05.1 2.501.33.504.55.0010.8 63.50.688.92.0127.04.9 2.501.34.005.56.0021.9 63.50.6101.62.5152.410.0 3.001.54.006.06.0021.6 76.20.7101.62.7152.49.8 3.002.04.005.66.0021.1 76.20.9101.62.5152.49.6 3.002.24.006.06.0019.5 76.21.0101.62.7152.48.9 3.002.34.006.07.0028.0 76.21.0101.62.7177.812.7 3.002.34.006.07.0030.0 76.21.0101.62.7177.813.6 3.002.34.006.07.0028.0 76.21.0101.62.7177.812.7 3.003.24.005.97.0033.0 76.21.5101.62.7177.815.0 3.002.64.006.3 76.21.2101.62.9 *2 x 11⁄4 *139.7mm x 3*6 x 5 *2 x 11⁄2 *139.7mm x 48 x 2 *21⁄2 x 25 x 11⁄2 8 x 21⁄2 *76.1mm x 11⁄2 5 x 28 x 3 *76.1mm x 25 x 21⁄2 8 x 4 3 x 11⁄4 5 x 38 x 5 3 x 11⁄2 *5 x 48 x 6 *3 x 2*165.1mm x 310 x 4 *3 x 21⁄2 *165.1mm x 410 x 5 *3 x 76.1mm *165.1mm x 139.7mm 10 x 6 4 x 11⁄4 *6 x 210 x 8 4 x 11⁄2 6 x 21⁄2 12 x 4 *4 x 2*6 x 76.1mm 12 x 6 *4 x 21⁄2 6 x 312 x 8 *4 x 76.1mm *6 x 412 x 10 4 x 3*6 x 139.7mm B C A D ADA CAP® Patented Pipe Nominal Dimensions O.D.Takeout Center to End SizeABCD InchesInchesInchesInchesInches mmmmmmmm 1.251.751.890.77 31.844.548.00.3 1.9001.251.751.890.77 48.331.844.548.00.3 1.372.002.020.88 34.850.851.30.4 1.251.751.890.92 31.844.548.00.4 2.3751.251.751.890.92 60.331.844.548.00.4 1.372.002.021.06 34.850.851.30.5 1.471.971.891.28 37.350.048.00.6 2.8751.471.971.891.28 73.037.350.048.00.6 1.372.002.021.50 34.850.851.30.7 Net OutletWt. NPT*Lbs. Inches Kg. 1/2 11/2 3/4 1 1/2 2 3/4 1 1/2 21/2 3/4 1 *ISO-7 threaded outlets are available upon request. Note: Sizes marked with an asterisk (*) are only available in Figure 250 Cast. Sizes without an asterisk are only available in Figure 350 Fabricated. Page 5 of 6 TFP1810 Figures 391, 392, 393, 312 and 313 Figure 341 E to E Figure 327 C to E C to E Figure 393 E to E Figure 392 E to E Figure 391 E to E Figure 313C to E C to E Figure 341 150 lbs. Flange Adapter C to EAppx. Wt.E to EAppx. Wt. nchesLbs.InchesLbs. mmkg.mmkg. 2.752.04.002.8 69.60.9101.61.3 2.752.24.003.2 69.92.0101.61.5 3.252.74.05.2 82.61.2101.62.4 3.755.04.008.0 95.32.3101.63.6 4.257.14.0010.2 108.03.2101.64.6 5.0011.96.0017.2 127.05.4152.47.8 5.5017.16.0021.4 139.77.8152.49.7 6.5027.56.0026.0 165.112.5152.411.8 7.7547.06.0038.4 196.921.3152.417.4 9.0068.08.0065.0 228.630.8203.229.5 10.00107.08.0091.0 254.048.5203.241.3 Nominal Size 11/4" 11/2" 2" 21/2" 3" 4" 5" 6" 8" 10" 12" Figure 327 Cross Figures 391, 392 and 393 Adapter Nipples E to EAppx. Wt.C to EAppx. Wt.C to EAppx. Wt. InchesLbs.InchesLbs.InchesLbs. mmKg.mmKg.mmKg. 4.000.81.750.41.380.4 101.60.444.50.235.10.2 4.000.91.750.51.380.5 101.60.444.50.235.10.2 4.001.21.880.61.380.6 101.60.547.80.335.10.3 4.001.92.000.71.501.1 101.60.950.80.338.10.5 4.002.52.251.41.501.2 101.61.157.20.638.10.5 6.005.52.632.41.752.2 152.42.566.81.144.51.0 6.007.42.884.12.003.3 152.43.473.21.950.81.5 6.009.53.135.62.004.6 152.44.379.52.550.82.1 6.0014.23.8811.12.008.7 152.46.498.65.050.83.9 8.0027.04.3814.02.139.1 203.212.211.36.454.14.1 8.0033.04.8822.02.2516.7 203.215.0124.010.057.27.6 Nominal Size 11/4" 11/2" 2" 21/2" 3" 4" 5" 6" 8" 10" 12" Figure 312Figure 313 221/2° Elbow111/4° Elbow Figures 327 and 341 Figure 312 C to E C to E General Notes: It is the Designer’s responsibility to select products suitable for the intended service and to ensure that pressure ratings and performance data is not exceeded. Always read and understand the installation instructions (IH-1000). Never remove any piping component or correct or modify any piping deficiencies without first depressurizing and draining the system. Material and gasket selection should be verified to be compatible for the specific application.Certified Company TYCO FIRE PRODUCTS, 451 North Cannon Avenue, Lansdale, Pennsylvania 19946 Printed U.S.A. Page 6 of 6 TFP1810 Figure 321 Figure 321 C to E C to E 11⁄2 x 11⁄2 x 11⁄4 6 x 6 x 4 2 x 2 x 11⁄2 6 x 6 x 5 21⁄2 x 21⁄2 x 11⁄4 8 x 8 x 2 21⁄2 x 21⁄2 x 11⁄2 8 x 8 x 3 21⁄2 x 21⁄2 x 28 x 8 x 4 3 x 3 x 11⁄2 8 x 8 x 5 3 x 3 x 28 x 8 x 6 3 x 3 x 21⁄2 10 x 10 x 2 4 x 4 x 11⁄4 10 x 10 x 3 4 x 4 x 11⁄2 10 x 10 x 4 4 x 4 x 210 x 10 x 5 4 x 4 x 21⁄2 10 x 10 x 6 4 x 4 x 310 x 10 x 8 5 x 5 x 212 x 12 x 3 5 x 5 x 21⁄2 12 x 12 x 4 5 x 5 x 312 x 12 x 5 5 x 5 x 412 x 12 x 6 6 x 6 x 212 x 12 x 8 6 x 6 x 21⁄2 12 x 12 x 10 6 x 6 x 3 Figure 321 Reducing Tee NominalC to EAppx. Wt.NominalC to EAppx. Wt. SizeInchesLbs.SizeInchesLbs. Inches mmKg.Inches mmKg. 3.252.06.5026.6 82.60.9165.112.1 3.252.76.5027.0 82.61.2165.112.2 3.754.27.7536.2 95.31.9196.916.4 3.754.27.7536.5 95.31.9196.916.6 3.754.37.7536.6 95.32.0196.916.6 4.255.37.7536.8 108.02.4196.916.7 4.255.57.7537.0 108.02.5196.916.8 4.255.89.0057.1 108.02.6228.625.9 5.009.89.0057.4 127.04.4228.626.0 5.009.99.0057.6 127.04.5228.626.1 5.0010.19.0057.8 127.04.6228.626.2 5.0010.39.0058.0 127.04.7228.626.3 5.0010.59.0058.4 127.04.8228.626.5 5.5014.510.0080.2 139.76.6254.036.4 5.5014.810.0080.5 139.76.7254.036.5 5.5015.210.0080.7 139.76.9254.036.6 5.5015.810.0080.9 139.77.2254.036.7 6.5026.510.0091.4 165.111.9254.041.5 6.5026.510.0091.8 165.112.0254.041.6 6.5026.5 165.112.0 S5 - 4 Schedule-10®/Schedule-40® Fully Listed and FM Approved Sprinkler Pipe When you specify Schedule-10/Schedule-40 sprinkler pipe you get UL listed and FM approved product. Although these products do not require separate approvals, Schedule-10/Schedule-40 gives you the extra quality assurance you demand. Our Sch-10 (11⁄4" – 8") pipe and Sch-40 (1" – 21⁄2") pipe have passed the same thorough lab testing as our other listed pipe products, and receive periodic mill inspections from both UL and FM agents to ensure consistent quality. Galvanized Pipe Schedule-10/Schedule-40 product can be “hot-dip” galvanized to meet FM. Superior Coating Our advanced formula mill coating offers a clean, durable surface. It is also paint- ready for custom color applications without special preparation. The internal surface of all black Fire Sprinkler pipe up to 4.5000” in diameter shall be coated with Allied Tube & Conduit Antibacterial Formula “ABF”. American Made Meets “Buy American” requirement and is available through distributors in the USA, Canada and Mexico. Specifications & Approvals Schedule-10/Schedule-40 pipe are in compliance with the following: ASTM A135 and NFPA 13. Both pipe products have a working pressure rating of 300 psi maximum and also meet the stringent requirement for the following tests: Welded Outlets, Hydrostatic Pressure, Side Wall Rupture, Vibration Test. Submittal Data Sheet Project: Engineer: Locations: Sprinkler Contractor: Specification Reference: Date: System Type: Comments: Stamp Here FM ListedApprovedListed American Tube and Pipe was acquired by Allied Tube and Conduit on February 1, 1997. The engineered lightwall and standard wall family of products although they have different names are the same in all respects with regard to strength, weight, bundle count, listings and approvals. For example, Dyna-Flow and Super Flo are the same product as are Dyna Thread and Super 40. XL is manufactured with Exterior galvanized coating. BLT is manufactured with Black lacquer coating. Sch-40 Specications NPSNominal I.D.Wt.Wt. (H2O Filled)Pcs/Wt/Lift (21')Wt/Lift (24')Wt/Lift (25') In; mmIn; mmLbs/Ft; Kg/mLbs/Ft; Kg/mLiftLbs; KgLbs; KgLbs; Kg 1"1.0491.6802.05702,4702,8222,940 2526.62.53.05701,1201,2801,334 11⁄4"1.3802.2702.93512,4312,7782,894 3235.14.364.36511,1031,2601,313 11⁄2"1.6102.7203.61442,5132,8722,992 4040.94.05.37441,1401,3031,357 2"2.0673.6505.13302,3002,6282,738 5052.55.47.63301,0431,1921,242 21⁄2"2.4695.7907.86192,3102,6402,750 6562.78.611.73191,0481,1971,247 Sch-10 Specications NPSNominal I.D.Wt.Wt. (H2O Filled)Pcs/Wt/Lift (21')Wt/Lift (24')Wt/Lift (25') In; mmIn; mmLbs/Ft; Kg/mLbs/Ft; Kg/mLiftLbs; KgLbs; KgLbs; Kg 1"1.0971.4001.81912,6753,0533,185 2527.92.12.70911,2131,3851,445 11⁄4"1.4421.8102.52612,3192,6642,760 3236.62.73.75611,0521,2081,252 11⁄2"1.6822.0803.04612,6643,0453,172 4042.73.14.52611,2081,3811,439 2"2.1572.6404.22372,0512,3442,442 5054.83.96.28379301,0631,108 21⁄2"2.6353.5305.89302,2242,5422,648 6566.95.38.77301,0091,1531,201 3"3.2604.3307.94191,7281,9752,057 8082.86.411.8219784896933 4"4.2605.61011.78192,2382,5582,665 90108.28.317.53191,0151,1601,209 5"5.2957.7717.33101,6321,8651,943 125134.511.5625.8010740846881 6"6.3579.29023.03101,9512,2302,322 150161.513.834.27108851,0121,053 8"8.24916.49040.1572,4242,7702,885 200209.524.559.7571,1001,2561,309 CPVC PIPE FIXINGS 800-333-0852 www.erico.com 86 One-hole Wrap Around Strap for CPVC Pipe •Size Range: 3/4” thru 2” CPVC pipe •Surface Finish: Electro-zinc plated •Support CPVC pipe horizontally from top or side of beam • Flared edges protect the CPVC piping PartNominal ABMax. Hanger NumberPipe SizeSpacing 1070075EG3/4”1-1/4”2-3/8”5-1/2’ 1070100EG1”1-7/16”2-11/16”6' 1070125EG1-1/4”1-5/8”3-1/16”6-1/2’ 1070150EG1-1/2”1-3/4”3-5/16”7’ 1070200EG2”1-7/8”3-11/16”8’ Two-hole Strap for CPVC Pipe •Size Range: 3/4” thru 2” CPVC pipe •Surface Finish: Electro-zinc plated •Support CPVC pipe horizontally from top, bottom or side of beam •Retainer dimples secure hanger to pipe during installation • Flared edges protect the CPVC piping PartNominal ABMax. Hanger NumberPipe SizeSpacing 1080075EG3/4”3-1/4”2-1/4”5-1/2’ 1080100EG1”3-1/2”2-1/2”6' 1080125EG1-1/4”4-1/4”3-1/4”6-1/2’ 1080150EG1-1/2”4-7/16”3-7/16”7’ 1080200EG2”4-15/16”3-15/16”8’ 1-3/16"1-3/16" A B .230 DIA..230DIA. 1 3/16"13/16" B.230 DIA..230DIA. A CPVC PIPE FIXINGS 107 CPVC PIPE FIXINGS 108 10 CPVC PIPE FIXINGS 87800-333-0852 www.erico.com Side Mount Strap for CPVC Pipe •Size Range: 3/4” thru 2” CPVC pipe •Surface Finish: Electro-zinc plated •Support CPVC pipe horizontally from top or bottom of beam •Retainer dimples secure hanger to pipe during installation • Flared edges protect the CPVC piping PartNominal ABMax. Hanger NumberPipe SizeSpacing 1090075EG3/4”2-5/16”1-11/16”5-1/2’ 1090100EG1”2-5/8”1-15/16”6' 1090125EG1-1/4”2-15/16”2-5/16”6-1/2’ 1090150EG1-1/2”3-3/16”2-1/2”7’ 1090200EG2”3-5/8”3”8’ Stand-off Two-hole Strap for CPVC Pipe •Size Range: 3/4” thru 2” CPVC pipe •Surface Finish: Electro-zinc plated •Support CPVC pipe off of the vertical face of structural or composite wood joists with a minimum of 3/8” web thickness • Flared edges protect the CPVC piping PartNominal ABMax. Hanger NumberPipe SizeSpacing SO12A3/4”2-11/16”3-1/4”5-1/2’ SO16A1”2-15/16”3-1/4”6' SO20A1-1/4”3-5/16”3-1/4”6-1/2’ SO24A1-1/2”3-9/16”4-1/2”7’ SO32A2”4-1/16”5”8’ 1-3/16"1-3/16" B A .230 DIA..230DIA. .200 DIA..200DIA. A 1.001.00 B NEWNEW CPVC PIPE FIXINGS 109 CPVC PIPE FIXING SO 10 BB-SC 100 &S02 BBSC100_rev0.CDR MILWAUKEEVALVE 1 2-"/" Approvedby:NYCBoardofStds.&Appeals, Cal.#996-81-SM(175psi) 720-83-SA(350&500psi) D Theinformationpresentedonthissheetiscorrectatthetimeofpublication.Milwaukee Valvereservestherighttochangedesign,and/ormaterialspecificationswithoutnotice. Forthemostcurrentinformationaccess.www.milwaukeevalve.com 1 2- BRONZEBUTTERFLYVALVE ONE-PIECE,FULL-PORT 175PSI THREADEDENDS C US APPROVED MATERIALSLIST butterball SLOWCLOSE 1 2 3 4 5 6 PertainstoBB-SC100only. PertainstoBB-SCS02only. AREDIMENSIONSUSINGSCHEDULE40 PIPE AREDIMENSIONSUSINGSCHEDULE80 PIPE ISFLOWRESISTANCEEXPRESSEDIN EQUIVALENTLENGTHOFSCHEDULE40 PIPE ISTHEWRENCHMAKE-UPLENGTH M-40 M-80 N-40 W FEATURES Slowopeningandclosing -Signalsdiscmovement -FactoryorFieldinstallation -10Amp/115VAC-60Hz -0.5Amp/28VDC Quarterturnoperation WaterHammerelimination Optionalinternaltamperswitch (Indooruseonly). GroovedEndsAvailablein Sizes2”and2-1/2” “M" B “L" BUTTERFLYVALVE 76G2 OPEN R LISTED M L “K” (MAX ENTRY) “C"C 4-1/2” BB-SC100 Sizes1”,1-1/4”,1-1/2”,2”,2-1/2” W A 4-1/2” “C"C BUTTERFLYVALVE 76G2 OPEN R LISTED W A J D BB-SCS02 (IncludesSwitch) DIMENSIONS ALLDIMENSIONS-INCHES 2-1/2” 4.13 3.82 3.19 3.50 4.66 1.18 1.29 2.47 2.32 10.00 1.75 DIM A B C D J K L M-40 M-80 N-40 W 1 2 3 4 5 6 1” 2.13 3.16 1.56 1.72 4.16 .66 .83 1.10 .96 2.25 1.13 1-1/4” 2.63 3.31 1.94 2.11 4.16 .73 .90 1.38 1.28 2.00 1.25 1-1/2” 2.88 3.41 2.19 2.38 4.51 .73 .10 1.61 1.50 2.50 1.41 2” 3.25 3.63 2.75 3.07 4.76 .79 1.41 2.07 1.94 2.25 1.69 ValveSize 5 4 3 6 1 2 7 ITEMPARTMATERIALSASTMSPEC. 1 IndicatorIronF0008P 2 Housing 3 Body 4 HandleBrass ASTMB176UNS C85800 5 Disk StainlessSteel ASTMA276, Type304 6 DiskSeal EPDM 7 SwitchHousing (BB-SCS02)Aluminum Bronze ASTM584UNS C8440 71 Fire Protection, Sprinkler Service Gauge Type 1005P, XUL Grade B (3-2-3%) •Underwriters Laboratory listed and Factory Mutual approved •Corrosion-resistant ABS case •Heat-resistant polycarbonate push- in window •Patented PowerFlex™ movement with polyester segment •True Zero™ indication, a unique safety feature Reference Bulletin CSG-3 GAUGE SPECIFICATIONS Type no.:1005P, XUL Size: 31⁄2˝ Case:ABS (Acrylonitrile Butadiene Styrene) Ring:None Window:Polycarbonate, push-in Dial:Black figures on white background Pointer:Black, aluminum Bourdon tube:“C” shaped bronze Movement:Patented PowerFlex with polyester segment Socket:Brass, soft soldered Restrictor:None Ashcroft ® fire protection sprinkler gauges are Underwriters Laboratory listed and Factory Mutual approved for fire protection sprinkler service. The case material on Type 1005P, XUL gauges is ABS. The 0-300 psi pressure range is used on “wet” sys- tems where water is available to the sprinkler heads. The 0-80 retard to 250 psi pressure range is used on dry systems where the lines are filled with air pressure until system activation. The patented Power Flex move- ment with polyester segment is de- signed to provide unequalled shock and vibration resistance resulting in superior performance and extended gauge life. MADE IN U.S.A. NOTES LISTED U L GAUGE OPTIONS Customized dials Other UL listed ranges on application Connection:1⁄4 NPT lower Ranges:0-300 psi (water) 0-80 retard to 250 psi (air) UL 393 Listed, UL of Canada Listed and FM approved. Equivalent (single or dual scale) metric scales are available TO ORDER THESE TYPE 1005P, XUL GAUGES: Select:35W1005PH02LXUL300 # 1.Dial Size: 31⁄2˝ 2.Patented PowerFlex™ Movement 3.Case Type Number: 1005 4.Case Type Material: ABS 5.Socket Material: Brass 6.Connection Size/Location: 1⁄4 NPT lower 7. UL listed, FM approved 8.Range: 300 psi True Zero indication, a standard feature on these gauges, reduces the potential risk of installing a dam- aged gauge on your equipment. Consult factory for guidance in product selection Phone (606) 986-9333 FAX 1-800-282-3732 email at: dresser-berea-pic @ dspn.com Fire Protection Sprinkler Service Gauge Type 1005 XUL – 31⁄2˝ www.dresser.com/instruments ©Dresser Instrument Division 6/97 Dimensions A B D C D E 1/4 NPT SIZE/TYPEABCDE 3 1 ⁄2 ˝0.701.140.720.560.47 1005P(94)(29)(69)(14.2)(11.9) 172 Mechanical Pressure Accuracy Definitions ACCURACY: Accuracy—the conformity of indica- tion to an accepted standard or true value. Accuracy is the difference (er- ror) between the true value and the indication expressed as a percent of the span. It includes the combined effects of method, observer, appara- tus and environment. Accuracy error includes hysteresis and repeatability errors but not friction error. It is deter- mined under specific conditions. (Nor- mal position, 73.4°F (23°C), and 29.92 in Hg barometric pressure.) The following tables define the ASME B40.1 and DIN accuracy grades used by Ashcroft products. Accuracy of a pressure gauge may be expressed as percent of span or per- cent of indicated reading. Percent of span is the most common method. Percent of indicated reading is usually limited to precision test gauges and unless specifically spelled out, it may be assumed that an accuracy of ±1⁄2% means ±1⁄2% of span. GRADE 4A: gauges offer the highest accuracy and are calibrated to ±0.1% of span over the entire range of the gauge. The gauges are called laboratory precision test gauges and are generally 81⁄2", 12", or 16" dials. These high-accuracy gauges may be temperature compen- sated. They must be handled carefully in order to retain accuracy. GRADE 3A: gauges are calibrated to an accuracy of ±0.25% of span over the entire range of the gauge. The gauges are called test gauges and are generally 41⁄2", 6" or 81⁄2" dials. The gauges are generally not temperature compen- sated (except Ashcroft Type 1082). GRADE 2A: gauges are calibrated to an accuracy of ±0.5% of span over the entire range of the gauge. These gauges are gen- erally used by the petrochemical in- dustry for process pressure measure- ment. They are often referred to as process gauges and are usually sup- plied as 4 1⁄2" and 6" cases and are not temperature compensated. GRADE 1A: gauges are calibrated to an accuracy of ±1% over the entire range of the gauge. These gauges are high-quality industrial gauges and are supplied in 21⁄2", 31⁄2" and 41⁄2" sizes. GRADE A: gauges are calibrated to an accuracy of ±1% of span over the middle half of the scale and ±2% of span over the first and last quarters of the scale. These gauges are often referred to as industrial gauges and are usually sup- plied in 2 1⁄2", 31⁄2" and 4 1⁄2" case sizes. GRADE B: gauges are calibrated to an accuracy of ±2% of span over the middle half of the scale and ±3% of span over the first and last quarters of the scale. This accuracy of gauge represents the majority of those manufactured and used for pressure measurement on water pumps, swimming pool filters, air compressors, filter regulations, etc. These gauges are often referred to as commercial or utility gauges and are supplied in 11⁄2", 2", 21⁄2", 31⁄2" and 4 1⁄2" case sizes. GRADE C: gauges are calibrated to an accuracy of ±3% of span over the middle half of the scale and ±4% of span over the first and last quarters of the scale. These are used in similar applications as Grade B gauges except that they are less accurate. GRADE D: gauges are calibrated to an accuracy of ±5% of span over the entire scale. These 5% gauges are used as indica- tors when minimal accuracy is re- quired for application on water pumps and pool filters. DIN STANDARDS Permissible Error % ofClassSpan for Entire Span 0.60.6 1.01.0 1.51.5 2.52.5 ACCURACY EXAMPLES AccuracyPermissible ErrorRangeSpanGrade% of Span Dial Units 0/100 psi100 psi1A1.01 psi 0/400 kPa400 kPa2A0.52 kPa 0/1000 bar1000 barB3 (0/250 & 750/1000 bar)30 bar 2 (250/750 bar)20 bar -100/400400 kPa2A0.52 kPa 30" Hg/44.7 psi4A0.1.045 psi 30 psi.022 in Hg The last item (30" Hg/30 psi)deserves some explanation. The span is defined as the algebraic difference between the limits of the scale. 30" Hg = -14.7psi Span = 30 psi -(-14.7) = 44.7 psi. 0.1% of 44.7 psi = .045 psi or .022 Hg. ACCURACY EXAMPLES Permissible Error % of Span Type ofLowerMiddleUpperMax. Friction GaugeGrade25%50%25%(% of Span) Precision 4A 4A0.10.10.1See NoteTest (Heise) Test 3A0.250.250.250.25(1082) Process 2A0.50.50.50.5(1279) Industrial/ Hydraulic1A1.01.01.01.0 (1009) Industrial/ HydraulicA2.01.02.01.0 (1010, 1188, 1490) Commercial/ UtilityB3.02.03.02.0 (1000, 1008) Note: Grade 4A gauges must remain within 0.1% before and after being lightly tapped. Product Description Ball Valves Central Sprinkler Company 451 North Cannon Avenue, Lansdale, Pennsylvania 19446 Standard Port 150 PSI Saturated Steam 400 W.O.G. The Central Model F19 Ball Valves are constructed of forged brass which ensures that there are no pin holes which may occur in alternate processes. A large port size ensures good flow characteristics. Teflon* seats ensure smooth operation under normal operating conditions. Each Ball Valve is tested twice with air under water to assure consistent quality. Central Ball Valves include a vinyl covered handle for a comfortable, smooth grip. (Mfg. Source: Non- Domestic) Ball Valves *Teflon is a trademark of the DuPont Corp. The Central Model F19 Ball Valves are recommended primarily for shut- off service or throttling flow where desired. Central Ball Valves are of high-quality construction and are rated at 150 psi with saturated steam, 400 psi with water, oil or gas, non- shock, well in excess of normal operating requirements in fire protection service. F191-92 Bore Nom.Size Size A B C (D) 1⁄4"1.651.503.310.320 1⁄2"1.901.603.310.396 3⁄4"2.201.703.310.591 1"2.642.014.650.787 11⁄4"3.002.174.651.050 11⁄2"3.352.605.281.260 2"3.822.805.281.500 A B C D Dimensions (inches) No. 27-4.0 Central Sprink No. 4-8.0 © 1992 Central Sprinkler Company Printed in U.S.A. CL O S E 90° OP E N 1 2 3 4 5 6 78910 Central Sprinkler Company 451 N. Cannon Avenue, Lansdale, PA 19446 Phone (215) 362-0700 FAX (215) 362-5385 Bulletin F19.1 No. Description Material Specification 1NutBrassASTM B-16-C36000 2HandleSteelASTM A-283-D 3Stem Gland ScrewBrassASTM B-16-C36000 4Stem PackingTeflon*PTFE 5Thrust PackingTeflon*PTFE 6StemBrassASTM B-16-C36000 7BodyForged BrassASTM B-124-C37700 8Ball Disc PackingTeflon*PTFE 9Ball DiscBrassASTM B-16-C36000 10End PlugForged BrassASTM B-124-C37700 *Teflon is a trademark of the DuPont Corp. Bill of Materials Central Sprinkler Company 451 North Cannon Avenue, Lansdale, Pennsylvania 19446 4-91F17 Product Description The Central Model F17 3-Way Bronze Globe Valves are designed for general service as shut-off, throttling, or drain valves. The Central Model F17 3-Way Bronze Globe Valves provide positive shut-off under normal operating conditions. They are recommended for water service only. The Central Model F17 3-Way Bronze Globe Valves are of cast bronze construction in strict accordance with ASTM B-62 specifications 85-5-5-5 for superior corrosion resistance. The hand wheel is manufactured from cast iron materials to meet or exceed the requirements of Underwriters Laboratories, Inc., Factory Mutual, The American Water Works Association C-509 and ASTM A-126, Class B Standards. The Central Model F17 3-Way Bronze Globe Valves are rated with cold water at 200 psi, non-shock for cold water service, and are tested twice, air under water for consistent quality. The Central Model F17 3-Way Bronze Globe Valves have a soft rubber seat for tight shut-off under all operating conditions. (Mfg. Source: Non-Domestic) 3-Way Globe Valves 3-Way Bronze Globe Valves 1⁄4 Inch ItemDescriptionMaterialSpecification Bill of Materials 1BodyBronzeASTM B-62 2Hand WheelCast IronASTM A-126-B 3Hand Wheel NutSteelCommercial 4PackingNon-AsbestosCommercial 5Packing GlandBrassASTM B-16 6Packing NutBrassASTM B-16 7StemBrassASTM B-16 1 2 3 4 5 6 7 2.00 2.45 1.69 No. 27.3.0 Central Sprink No. 4-7.0 © 1991 Central Sprinkler Company Printed in U.S.A. Ordering Information Ordering Information: When placing an order, indicate the full product name. Please specify the quantity, model, style, orifice size, temperature rating, type of finish or coating, and sprinkler wrench. Availability and Service: Central sprinklers, valves, accessories, and other products are available through- out the U.S. and Canada, and internationally, through a network of Central Sprinkler distribution centers. You may write directly to Central Sprinkler Company, or call (215) 362- 0700 for the distributor nearest you. Guarantee: Central Sprinkler Company will repair and/or replace any products found to be defective in material or workmanship within a period of one year from the date of shipment. Please refer to the current Price List for further details of the warranty. Patents: Patents are pending. Conversion Table: 1 inch = 25.400 mm 1 foot = 0.3048 M 1 pound = 0.4536 kg 1 foot pound = 1.36 Nm 1 psi = 6.895 kpa = 0.0689 bar = 0.0703 kg/cm2 1 U.S. gallon = 3.785 dm3 = 3.785 liters Conversions are approximate. F17.0 Central Sprinkler Company 451 N. Cannon Avenue, Lansdale, PA 19446 Phone (215) 362-0700 FAX (215) 362-5385