The URL can be used to link to this page

Home My WebLink AboutA13-0026 Relay Card N8909 9/97 ADEMCO No. 4204 RELAY MODULE For Use With Control/Communicators Supporting Relay Module Connection Via Keypad Lines INSTALLATION INSTRUCTIONS GENERAL INFORMATION When the 4204 is mounted remotely, holes on its back The 4204 Relay Module adds from one to four dry, form C permit it to be mounted horizontally or vertically.Wires can exit (SPDT)relay outputs to compatible control/communicators. It from the side or via the breakout on the back of its housing. interfaces to the control's keypad wiring. The DIP switch must be set with its position 1 "OFF"and when The 4204 can be mounted inside the control's cabinet or the installation is completed,the uniYs tamper-protected cover mounted remotely. must be replaced. If mounted remotely, the 4204 has two forms of protection. Affix the connections label that accompanies the 4204 to the First, the 4204 has a built-in tamper switch which allows it to inside of the 4204's cover(if the cover is used)or to the inside detect and report the removal of its cover to the control. of the control's cover. Second, communication to the 4204 is supervised so that it CONNECTIONS AND SETTINGS cannot be disconnected from the keypad wiring without Select and set an address for the 4204, using its DIP switch detection by the control. If the wiring is cut,a tamper or alarm as shown in the table below. Each 4204 used with the control signal will result, to indicate that this device (and possibly must be assigned a unique address so the control can identi- other devices connected to the keypad wiring) has become fy the 4204 and communicate with it properly. The address to inoperative. be set is determined by the particular control to be used, and INSTALLATION the control's installation instructions must be consulted. As For UL Installations: shipped, the DIP switch is set for an address of"0". When used with controls which do not support cover Connections to the 4204's four relays are made via 12-posi- tamper or supervise communications wiring to the 4204, tion terminal block T82. Refer to the control's installation mount the 4204 inside the control's cabinet. instructions for specific information on how to program the control's various activation options for the relays. When used with controls which support cover tamper Connections to the control's keypad wiring points can be and supervise communications wiring to the 4204, the made via 4-position terminal block T61,the 4-pin plug,or both 4204 may either be mounted inside the control's cabinet (Wire color connections are the same). See the diagram on the or mounted remotely. other side of this page, When mounted inside the control's cabinet, some controls allow the 4204 to be mounted horizontally as follows: insert SPECIFICATIONS the self-tapping screws (provided) in two adjacent raised Physical 6-7/16"W x 4-1/4" H x 1-1/4" D tabs on the back of the cabinet. Leave the heads projecting (163mm x 108mm x 32mm) 1/8". Hang the 4204 on the screw heads via two of the slot- Electrical ted holes on the back of its housing. The 4204's cover need Input Voltage: 12VDC nominal (10-14VDC), from control's not, in this case, be tamper-protected. If the DIP switch is set remote keypad connection points with its position 1 "ON" (see the table below), the cover can be left off. See the control's instructions for additional infor- Input Current: 15mA standby+40mA per active relay mation. Contact Rating: 2A max. at 28VDC/AC (resistive loads) DIP SWITCH SETTINGS OFF� �'►ON SWITCH 4204 ADDRESS SETTINGS POSITION ("—" means"OFF") '�� 1 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 N� «' 2 ON — ON — ON — ON — ON — ON — ON — ON — �� 3 ON ON — — ON ON — — ON ON — — ON ON — — A� «" 4 ON ON ON ON — — — — ON ON ON ON — — — — �'� ~ 5 ON ON ON ON ON ON ON ON � �—DIP SWITCH: (WHITE AREAS DENOTE SWITCH HANDLES) POSITIONS 2-5: DETERMINE 4204's ADDRESS. CONSULT CONTROL'S INSTRUCTIONS FOR ADDRESS TO USE. SHOWN SET(AS SHIPPED)FOR ADDRESS=0. POSITION 1: DETERMINES COVER TAMPER RESPONSE. ON=DISABLED(SHOWN,AS SHIPPED) OFF=ENABLED(COVER IS TAMPER-PROTECTED) 4 4204 RELAY C 4 Nc ��DIPSWITCH TYPICAL o FOR SETTING DEVICE ADDRESS (SHOWN"OFF") NO AND ENABLING/DISABLING TAMPER RELAY OO C COVER TAMPER(REED)SWITCH � OO NC 1 4-PIN KEYPAD PLUG� � No RELAY CONTACTS ARE 4-PINCOA____.___ IR�ELAV O � NOT SUPERVISED 1 I � I O NC EITHER OR BOTH � U O NO CAN BE USED � a RELAV O � TB1 Y � . 1 � Nc 13 14 15 16 � � NO YEL DATA IN �TB2 FROM CONTROL B�K (-)GROUND GRN DATA OUT TO CONTROL RED (+)12V 4204 CONNECTIONS REFER TO THE INSTALLATION INSTRUCTIONS FOR THE CONTROL WITH WHICH THIS DEVICE IS USED FOR DETAILS REGARDING THE LIMITATIONS OF THE ENTIRE ALARM SYSTEM. ADEMCO LIMITED WARRANTY Alarm Device Manufacturing Company, a Division of Pittway Corporation, and its divisions, subsidiaries and affiliates ("Seller"), 165 Eileen Way, Syosset, New York 11791, warrants its products to be in conformance with its own plans and specifications and to be free from defects in materials and workmanship under normal use and service for 24 months from the date stamp control on the product or, for products not having an Ademco date stamp, for 12 months from date of original purchase unless the installation instructions or catalog sets forth a shorter period, in which case the shorter period shall apply. Seller's obligation shall be limited to repairing or replacing, at its option, free of charge for materials or labor, any product which is proved not in compliance with Seller's specifications or proves defective in materials or workmanship under normal use and service. Seller shall have no obligation under this Limited Warranty or otherwise if the product is altered or improperly repaired or serviced by anyone other than Ademco factory service. For warranty service, return product transportation prepaid, to: Ademco Factory Service, 165 Eileen Way, Syosset, New York 11791. THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, OF MERCHANTABILITY, OR FITNESS FOR A PARTICU- LAR PURPOSE OR OTHERWISE, WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. IN NO CASE SHALL SELLER BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, OR UPON ANY OTHER BASIS OF LIABILITY WHATSOEVER, EVEN IF THE LOSS OR DAMAGE IS CAUSED BY THE SELLER'S OWN NEGLIGENCE OR FAULT. Seller does not represent that the products it sells may not be compromised or circumvented; that the products will prevent any personal injury or property loss by burglary, robbery,fire or otherwise;or that the products will in all cases provide adequate warning or protection. Customer understands that a properly installed and maintained alarm may only reduce the risk of a burglary, robbery, fire or other events occurring without providing an alarm, but it is not insurance or a guarantee that such will not occur or that there will be no personal injury or property loss as a result. CONSEQUENTLY, SELLER SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJURY, PROPERTY DAMAGE OR OTHER LOSS BASED ON A CLAIM THE PRODUCT FAILED TO GIVE WARNING. However, if Seller is held liable, whether directly or indirectly, for any loss or damage arising under this Limited Warranty or otherwise, regardless of cause or origin, Seller's maximum liability shall not in any case exceed the purchase price of the product, which shall be the complete and exclusive remedy against Seller. This warranty replaces any previous warranties and is the only warranty made by Seller on this product. No increase or alteration, written or verbal, of the obligations of this Limited Warranty is authorized. ADEMCO GROUP 165 Eileen Way, Syosset, New York 11791 Copyright O 1997 PITTWAY CORPORATION