HomeMy WebLinkAboutDRB130182
Project Name:BEAR FISH WINDOWS DRB Number: DRB130182
Project Description:
REPLACE EXISTING WINDOWS WITH GARAGE DOOR TYPE WINDOWS (LIKE THE ONES AT THE
WEST VAIL FIRE STATION). THIS WILL NOT BE A DOOR. WOULD LIKE THE ABILITY TO OPEN
UP THE SPACE. WILL ONLY FILL AREA OF EXISTING WINDOW AND WILL NOT EXTEND TO THE
FLOOR.
Participants:
OWNER VANQUISH VAIL I LLC 05/23/2013
2211 N FRONTAGE RD
VAIL, CO
81657
APPLICANT VANQUISH VAIL I LLC 05/23/2013
2211 N FRONTAGE RD
VAIL, CO
81657
Project Address:2211 N FRONTAGE RD W VAILLocation:
BEAR FISH RESTAURANT
Legal Description:Lot: 1,2, Block: Subdivision: VAIL DAS SCHONE FIL 3
Parcel Number:2103-114-1501-7
Comments:
BOARD/STAFF ACTION
Motion By:Kjesbo Action: APPROVED
Second By:Forstl
Vote:3-0 Date of Approval: 06/19/2013
Conditions:
Cond: 8
(PLAN): No changes to these plans may be made without the written consent of Town of
Vail staff and/or the appropriate review committee(s).
Cond: 0
(PLAN): DRB approval does not constitute a permit for building. Please consult with
Town of Vail Building personnel prior to construction activities.
Cond: 201
(PLAN): DRB approval shall not become valid for 20 days following the date of
approval, pursuant to the Vail Town Code, Chapter 12-3-3: APPEALS.
Cond: 202
(PLAN): Approval of this project shall lapse and become void one (1) year following
the date of final approval, unless a building permit is issued and construction is
commenced and is diligently pursued toward completion.
Cond: CON0013284
(PLAN) The new window will be powdercoated on the exterior to match the existing
window trim.
Planner:Jonathan Spence DRB Fee Paid: $250.00
********************************************************************************************
TOWN OF VAIL, COLORADOCopy Reprinted on 05-23-2013 at 16:39:24 05/23/2013
Statement
********************************************************************************************
Statement Number: R130000666 Amount: $250.00 05/23/201304 :39 PM
Payment Method: Check Init: DR
Notation: CK# 2334
G.P.H. LLC DBA BEARFISH
-----------------------------------------------------------------------------
Permit No: DRB130182 Type: DRB-Minor Alt,Comm/Multi
Parcel No: 2103-114-1501-7
Site Address: 2211 N FRONTAGE RD W VAIL
Location: BEAR FISH RESTAURANT
Total Fees: $250.00
This Payment: $250.00 Total ALL Pmts: $250.00
Balance: $0.00
********************************************************************************************
ACCOUNT ITEM LIST:
Account Code Description Current Pmts
-------------------- ------------------------------ ------------
DR 00100003112200 DESIGN REVIEW FEES 250.00
-----------------------------------------------------------------------------
Department of Community Development
7MAY 2 3 2013 75 South Frontage Road
X0v1111 Of .:' Vail, CO 81657
Tel: 970-479-2128
TOWN OF VAIL www.vailgov.com
Development Review Coordinator
Application for Design Review
Minor Exterior Alteration
General Information: This application is required for all proposals involving minor changes to buildings and site
improvements, such as roofing, painting, window additions, landscaping, fences, retaining walls, etc. Applicable Vail
Town Code sections can be found at www.vailgov.com under Vail Information-Town Code Online. All projects requiring
design review must receive approval prior to submitting a building permit application. An application for Design Review
cannot be accepted until all required information is received by the Community Development Department, as outlined in
the submittal requirements. The project may also need to be reviewed by the Town Council and/or the Planning and
Environmental Commission. Design review approval expires one year from the date of approval, unless a building permit
is issued and construction commences.
Fee: $250 for Multi-Family/Commercial
$20 for Single Family/Duplex -*z F
❑ Single Family ❑ Duplex ❑ Multi-Family Commercial ' -►IESi AUR��T
Description of the Request: "RE?LAC�E_ C 1 S'� �6, L.`�/ti1�0 L S C� t7-(-�
A(L C a 2 T I J S L 1 t-a` H_ o E C-o L,.--)t-i- c i
L..)«` tioT 91- A "tooi2 . wouL't;- LIICL.
oi>6 � yp 1tig SPAc-F Fo^ 1uNCt-�f
Physical Address: ` oZ ( tJ• r ii • 1111 6%e__ �-' `l At L- C-0 • 8( 1'o S�
Parcel Number: 2 I O 3 114 I S C) ( :?- (Contact Eagle Co. Assessor at 970-328-8640 for parcel no.)
Property Owner: 1F_ L- LL C— VAn3 e+2 U k 5 1.-/ \/'A tl_
Mailing Address: a a ( < A-) CZ 2� . V^I L- , C•o . 8 t G S
Phon , 88 • 0 -9-88
Owner's Signature
Primary Contact/Owner Representative:
Mailing Address: 21A 1 /J • �P_,L2a-n i1q:k L ZP. F4 L...► O•a"� �-'�
Phone: 9 0 • y�-(p • 39
E-Mail: Fax:
For Office Use Only:
Cash CC: Visa /MC Last 4 CC # Exp. Date: Auth# Check# 'qz3,�q
Fee Paid: 4,3,50,00 Received From: -vPMLLC., DMA 8CAP-f-ISN
Meeting Date: b(o -\q- L DRB No.: R. f 3 n 19 2
Planner: Project No: PP ZY 13-0 a\R
Zoning: Land Use:
Location of the Proposal: Lot: Block: Subdivision: \/F}I L �5`SCI4n,0G FI LIOG
i
PROPOSED MATERIALS
Building Materials Type of Material Color
Roof
Siding
Other Wall Materials
Fascia
Soffits
Windows
Window Trim
A 4 J.✓i• .J J r�1 � l..t1 M .�,t a�y1
Doors
Door Trim
Hand or Deck Rails
Flues
Flashing
Chimneys
Trash Enclosures
Greenhouses
Retaining Walls
Exterior Lighting
Other
,r
"TROU=T990
Y NOW
NI
•
r
' AFTER
Aluminum Glass Doors 521 Series http://overheaddoor.comJcommercial-doors/Pages/aluminum-gla...
10 . • a\
• •
M
(/Pages/LandingPage.aspx)
1 -800-929-3667 (DOOR)
ALUMINUM GLASS DOORS
ji;ctii%l% i'k3Luhuiueii�idiii sllCVlapPath SkigLink)
Model 521
The Model 521 is a sectional aluminum door appropriate for environments where maximum light infiltration and/or
visual access is required. Designed to fit openings up to 26'2" (7976 mm) wide and 20'1" (6121 mm) high, the
model 521 features a wide, 2-3/4" (70 mm) center stile, 3-3/4" (95 mm) or 4-1/2" (114 mm) bottom rail, based on
door size.
Features
(iavascript:void(ft)
Options
(iavascriptwid(0);)
Downloads
-1N.'gC.cript:void(0);)
Section thickness
1 3/4" (45 mm)
Maximum standard width
26'2" (7976 mm)
1 of 4 5/20/13 8:53 AM
Aluminum Glass Doors 521 Series http://overheaddoor.comlcommercial-doors/Pages/aluminum-gla...
Maximum standard height
20'1" (6121 mm)
Material
6063-T6 aluminum
Standard finish
204R-1 clear anodized (painted white at no charge)
Center stile width
2 11/16" (69 mm)
End stile width
3 5/16" (85 mm)
Top rail width
2 3/8" (60 mm) or3 3/4" (95 mm)
Top intermediate rail width
2 1/8" (54 mm)
Bottom intermediate rail width
1 19/32" (40 mm)
Bottom rail width
3 3/4" (95 mm) or 1/2" (114 mm)
Weatherseals
Bottom, flexible PVC
Standard springs
10,000 cycle
Track
2" (51 mm)
Mounting
Angle
2 of 4 5/20/13 8:53 AM
Aluminum Glass Doors 521 Series http://ovenccaddoor.com/commercial-doors/Pages/aluminum-gla...
Operation
Manual pull rope
Hinges and fixtures
Galvanized steel
Lock
Galvanized, interior-mounted single unit
Glazing options:
- W" (3 mm) DSB
- V8" (3 mm)or V4" (6 mm) plexiglass
- 1/8" (3 mm) or 1/4" (6 mm)tempered
- V8" (3 mm) or V4" (6 mm) clear lexan
- V8" (3 mm) or V4" (6 mm) Low-E
- 1/8" (3 mm)or 1/4" (6 mm) solar bronze
- 1/4" (6 mm)wire glass
- 1/8" (3 mm) or 1/4" (6 mm) obscure
- 1/2" (12 mm) insulated glass: DSB, tempered, clear lexan, Low-E, solar bronze, or obscure
- 1/4" (3 mm)twin-wall, 3/8" (9 mm) twin-wall, or 5/8" (15 mm)triple-wall polycarbonate
Electric operator or chain hoist
Bottom sensing edge
3" track
Bracket mounting (not available on full vertical door tracks)
Higher-cycle springs in 25k, 50k, 75k, 100k cycles
Exhaust ports
Finish options-
- Bronze anodized
- Select from 197 standard powder coat colors or colored to match
specification
Four-section pass door
4�
(http:/tv,;vrw•overheaddoor.cum/commercial-doors/Documents/brochures/aluminum-door-systems-
brochure.pdf)
Aluminum Glass Doors Brochure(Models 511 and 521)(http://www.overheaddoor.com/commercial-
doors/Documents/brochures/aluminum-door-systems-brochure.pdf)
(http://www.overheaddoor.com/commercial-doors/Documents/warranty/1-year-limited-
warranty.pdf)
One Year Limited Warranty(http://www.overheaddoor.com/commercial-doors/Documents/warranty/1-year-
limited-warranty.pdf)
3 of 4 5/20/13 8:53 AM
The Genuinr. 'Mr OrtShvkL
". - '_.
SECTION 08360
SECTIONAL OVERHEAD DOORS
521 SERIES ALUMINUM SECTIONAL OVERHEAD DOORS
Display hidden notes to specifier by using `Tools'/`Options'/`View'/`Hidden Text'. On newer versions of
Microsoft Word click on round Windows logo in top left corner, Click on `Word Options'button at bottom of
drop down menu. Click on 'Display'on left menu bar, and check the box for 'Hidden Text'.
PART 1 GENERAL
1.1 SECTION INCLUDES
A. Glazed Aluminum Sectional Overhead Doors
B. Electric Operators and Controls.
C. Operating Hardware, tracks, and support.
1.2 RELATED SECTIONS
A. Section 03300 -Cast-In-Place Concrete: Prepared opening in concrete. Execution
requirements for placement of anchors in concrete wall construction.
B. Section 04810 - Unit Masonry Assemblies: Prepared opening in masonry. Execution
requirements for placement of anchors in masonry wall construction.
C. Section 05500 - Metal Fabrications: Steel frame and supports.
D. Section 06114 -Wood Blocking and Curbing: Rough wood framing and blocking for door
opening.
E. Section 07900 -Joint Sealers: Perimeter sealant and backup materials.
F. Section 08710 - Door Hardware: Cylinder locks.
G. Section 09900 - Paints and Coatings: Field painting.
H. Section 11150— Parking Control Equipment: Remote door control.
I. Section 16130 - Raceway and Boxes: Empty conduit from control station to door operator.
J. Section 16150 -Wiring Connections: Electrical service to door operator.
1.3 REFERENCES
A. AN!! IrDASMA 10^ -American National Standard Specifications for Sectional Overhead Type
Doors.
1.4 DESIGN / PERFORMANCE REQUIREMENTS
A. Wind Loads: Design and size components to withstand loads caused by pressure and
suction of wind acting normal to plane of wall as calculated in accordance with applicable
code.
08360-521 Series- 1
I
1. Design pressure of Ib/sq ft ( kPa).
B. Wiring Connections: Requirements for electrical characteristics.
1. 115 volts, single phase, 60 Hz.
2. 230 volts, single phase, 60 Hz.
3. 230 volts, three phase, 60 Hz.
4. 460 volts, three phase, 60 Hz.
C. Single-Source Responsibility: Provide doors, tracks, motors, and accessories from one
manufacturer for each type of door. Provide secondary components from source acceptable
to manufacturer of primary components.
1.5 SUBMITTALS
A. Submit under provisions of Section 01300.
B. Product Data: Manufacturer's data sheets on each product to be used, including:
1. Preparation instructions and recommendations.
2. Storage and handling requirements and recommendations.
3. Installation methods.
C. Shop Drawings: Indicate plans and elevations including opening dimensions and required
tolerances, connection details, anchorage spacing, hardware locations, and installation
details.
D. Manufacturer's Certificates:Certify products meet or exceed specified requirements.
E. Operation and Maintenance Data.
1.6 QUALITY ASSURANCE
A. Manufacturer Qualifications:Company specializing in manufacturing products specified in
this section with minimum five years documented experience.
B. Installer Qualifications: Authorized representative of the manufacturer with minimum five
years documented experience.
C. Products Requiring Electrical Connection: Listed and classified by Underwriters
Laboratories, Inc. acceptable to authority having jurisdiction as suitable for purpose
specified.
1.7 DELIVERY, STORAGE, AND HANDLING
A. Store products in manufacturer's unopened labeled packaging until ready for installation.
B. Protect materials from exposure to moisture until ready for installation.
C. Store materials in a dry, ventilated weathertight location.
1.8 PROJECT CONDITIONS
A. Pre-Installation Conference: Convene a pre-installation conference just prior to
commencement of field operations, to establish procedures to maintain optimum working
conditions and to coordinate this work with related and adjacent work.
PART 2 PRODUCTS
08360-521 Series - 2
2.1 MANUFACTURERS
A. Acceptable Manufacturer: Overhead Door Corp., 2501 S. State Hwy. 121, Suite 200,
Lewisville, TX 75067. ASD. Tel. Toll Free: (800) 275-3290. Phone: (469)549-7100. Fax:
(972)906-1499. Web Site: www.over nor cor . E-mail. sales @overheaddoor.com.
B. Substitutions: Not permitted.
C. Requests for substitutions will be considered in accordance with provisions of Section
01600.
2.2 GLAZED ALUMINUM SECTIONAL OVERHEAD DOORS
A. Glazed Sectional Overhead Doors: 521 Series Aluminum Doors by Overhead Door
Corporation.
1. Door Assembly: Stile and rail assembly secured with 1/4 inch (6 mm) diameter
through rods.
a. Panel Thickness: 1-3/4 inches (44 mm).
b. Center Stile Width: 2-11/16 inches(68 mm)
C. End Stile Width: 3-5/16 inches (84 mm)
d. Intermediate Rail Pair Width: 3-11/16 inches (94 mm).
e. Top Rail Width:
1) 2-3/8 inches (60 mm).
2) 3-3/4 inches (95 mm).
f. Bottom Rail Width:
1) 3-3/4 inches (95 mm).
2) 4-1/2 inches (114 mm).
g. Aluminum Panels: 0.050 inch (1.3 mm) thick, aluminum.
h. Stiles and Rails: 6063 -T6 aluminum.
i. Springs:
1) 10,000 cycles.
2) 25,000 cycles.
3) 50,000 cycles.
4) 75,000 cycles.
5) 100,000 cycles.
j. Glazing:
1) 1/8 inch (3 mm) Acrylic glazing.
2) 1/4 inch (6 mm) Acrylic glazing.
3) 1/8 inch (3 mm) Clear Lexan glazing.
4) 1/4 inch (6 mm) Clear Lexan glazing.
5) 112 inch (12.5 mm) Clear Lexan Insulated glazing.
6) 1/8 inch (3 mm)Tempered glass.
7) 1/4 inch (6 mm)Tempered glass.
8) 1/2 inch (12.5 mm)Tempered Insulating glass.
9) 1/4 inch (6 mm) Wire glass.
10) 1/8 inch (3 mm) Double Strength glass.
11) 112 inch (12.5 mm) Double Strength Insulating glass.
12) 1/8 inch (3 mm) Low E glazing.
13) 1/4 inch (6 mm) Low E glazing.
14) 112 inch (12.5 mm) Low E Insulated glazing.
15) 1/8 inch (3 mm) Solar Bronze glazing.
16) 1/4 inch (6 mm) Solar Bronze glazing.
17) 1/2 inch (12.5 mm) Solar Bronze Insulated glazing.
18) 1/8 inch (3 mm) Obscure glazing.
19) 1/4 inch (6 mm) Obscure glazing.
20) 1/2 inch (12.5 mm) Obscure Insulated glazing.
08360-521 Series-3
i
I
21) 1/4 inch (6 mm)Twin-Wall Polycarbonate (clear, bronze, white).
22) 3/8 inch (9.5 mm)Twin-Wall Polycarbonate (clear, bronze, white).
23) 5/8 inch (15.87 mm)Triple-Wall Polycarbonate (clear, bronze, white).
2. Finish and Color:
a. Anodized Finish: Clear anodized.
b. Anodized Finish: Bronze anodized.
C. Powder coat finish bronze light.
d. Powder coat finish bronze medium.
e. Powder coat finish bronze dark.
f. Powder Coating Finish: Color as selected by Architect from manufacturer's
standard colors.
3. Windload Design: Provide to meet the Design/Performance requirements specified.
4. Hardware: Galvanized steel hinges and fixtures. Ball bearing rollers with hardened
steel races.
5. Lock: Interior galvanized single unit.
6. Weatherstripping:
a. Flexible bulb-type strip at bottom section.
b. Flexible Jamb seals.
C. Flexible Header seal.
7. Track: Provide track as recommended by manufacturer to suit loading required and
clearances available.
8. Manual Operation: Pull rope.
9. Manual Operation: Chain hoist.
10. Electric Motor Operation: Provide UL listed electric operator, size and type as
recommended by manufacturer to move door in either direction at not less than 2/3
foot nor more than 1 foot per second. Operator shall meet UL325/2010 requirements
for continuous monitoring of safety devices.
a. Entrapment Protection: Required for momentary contact, includes radio control
operation.
11 Pneumatic sensing edge !p to 1R feet(5.5 m)wide. Constant contact
only complying with UL 325/2010.
2) Electric sensing edge monitored to meet UL 325/2010.
3) Photoelectric sensors monitored to meet UL 325/2010.
b. Operator Controls:
1) Push-button operated control stations with open, close, and stop buttons.
2) Key operated control stations with open, close, and stop buttons.
3) Push-button and key operated control stations with open, close, and stop
buttons.
4) Flush mounting.
5) Surface mounting.
6) Interior location.
7) Exterior location.
8) Both interior and exterior location.
C. Special Operation:
1) Pull switch.
2) Vehicle detector operation.
3) Radio control operation.
4) Card reader control.
5) Photocell operation.
6) Door timer operation.
7) Commercial light package.
8) Explosion and dust ignition proof control wiring.
PART 3 EXECUTION
08360-521 Series-4
3.1 EXAMINATION
A. Do not begin installation until openings have been properly prepared.
B. Verify wall openings are ready to receive work and opening dimensions and tolerances are
within specified limits.
C. Verify electric power is available and of correct characteristics.
D. If preparation is the responsibility of another installer, notify Architect of unsatisfactory
preparation before proceeding.
3.2 PREPARATION
A. Clean surfaces thoroughly prior to installation.
B. Prepare surfaces using the methods recommended by the manufacturer for achieving the
best result for the substrate under the project conditions.
3.3 INSTALLATION
A. install overhead doors and track in accordance with approved shop drawings and the
manufacturer's printed instructions.
B. Coordinate installation with adjacent work to ensure proper clearances and allow for
maintenance.
C. Anchor assembly to wall construction and building framing without distortion or stress.
D. Securely brace door tracks suspended from structure. Secure tracks to structural members
only.
E. Fit and align door assembly including hardware.
F. Coordinate installation of electrical service. Complete power and control wiring from
disconnect to unit components.
3.4 CLEANING AND ADJUSTING
A. Adjust door assembly to smooth operation and in full contact with weatherstripping.
B. Clean doors, frames and glass.
C. Remove temporary labels and visible markings.
3.5 PROTECTION
A. Do not permit construction traffic through overhead door openings after adjustment and
cleaning.
B. Protect installed products until completion of project.
C. Touch-up, damaged coatings and finishes and repair minor damage before Substantial
Completion.
08360-521 Series-5