HomeMy WebLinkAboutB12-0029 REV9 Owner's Manual H E AT G L O.� � ��
\ , Owner's Manual
No one builds a better fire Installation and Operation
� �..
\
Models: o GAS-FIRED
6000C �
�
6000C-LP ��
6000C-IPI ,� � C `!� V$
6000C-IPILP
s000c � �� � LISTED
8000C-LP \ �f
8000C-IPI �� ,��a/'
8000C-IPILP '
• NOTICE ��O�
DO NOT DISCARD THIS MANUAL scq or
� • Important operating • Read,understand and follow • Leave this manual with �Q
and maintenance theseinstructionsforsafe partyresponsibleforuse
instructions included. installation and operation. and operation.
A WARNING: If the information in these A WARNING
instructions is not followed exactly, a fire HOT SURFACES!
or explosion may result causing property ( Glass and other surfaces are hot during
damage, personal injury, or death. operation AND cool down.
Hot glass will cause burns.
• DO NOT store or use gasoline or other flam- • DO NOT touch glass until it is cooled
mable vapors and liquids in the vicinity of this • NEVER allow children to touch glass
or any other appliance. • Keep children away
• CAREFULLY SUPERVISE children in same room as
• What to do if you smell gas fireplace.
- DO NOT try to light any appliance. • Alert children and adults to hazards of high temperatures.
High temperatures may ignite clothing orotherflammable
- DO NOT touch any electrical switch. DO materials.
NOT use any phone in your building. • Keep clothing, furniture, draperies and other flammable
- Immediately call your gas supplier from a materials away.
neighbor'S pI10112. FOIIOW tI12 gaS SUppll- This appliance has been supplied wifh an integral barrier
er'S IflStl"UCtIOfIS. to prevent direct contact with the fixed g/ass panel. DO
- If you cannot reach your gas supplier, Ca�� NOT operafe the appliance with the barrier removed.
the flre depa�..tment. Contact your dealer or Hearth & Home Technologies if the
barrier is not present or help is needed to properly install one.
• Installation and service must be performed
by a qualified installer, service agency, or the
gas supplier. in the Commonwealth of Massachusetts installation must be
performed by a licensed plumber or gas fitter.
See Table of Contents for location of additional Commonwealth
This appliance may be installed as an OEM installation in of Massachusetts requirements.
manufactured home (USA only)or mobile home and must be
installed in accordance with the manufacturer's instructions
and the manufactured home construction and safety standard, Installation and service of this appliance should be
Title 24 CFR, Part 3280 or Standard for Installation in Mobile r � performed by qualified personnel. Hearth & Home
Homes, CAN/CSA Z240MH, in Canada. °p 9�
Q � � Technologies suggests NFI certified or factory trained
This appliance is only for use with the type(s)of gas indicated NsT�T�t� professionals, or technicians supervised by an NFI
on the rating plate. certified professional.
Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12 1
Read this manual before installing or operating this appliance.
Please retain this owner's manual for future reference.
A. Congratulations This owner's manual should be retained for future
Congratulations on selecting a Heat&Glo gas fireplace,an reference. We suggest that you keep it with your other
elegant and clean alternative to wood burning fireplaces.
important documents and product manuals.
The Heat&Glo gas fireplace you have selected is designed The information contained in this owner's manual, unless
to provide the utmost in safety, reliability, and efficiency. noted otherwise, applies to all models and gas control
systems.
As the owner of a new fireplace, you'll want to read and
carefully follow all of the instructions contained in this Your new Heat & Glo gas fireplace will give you years of
owner's manual. Pay special attention to all cautions and durable use and trouble-free enjoyment. Welcome to the
warnings. Heat& Glo family of fireplace products!
Homeowner Reference Information We recommend that you record the following pertinent
information abouf your fireplace.
Model Name: Date purchased/installed:
Serial Number: Location on fireplace:
Dealership purchased from: Dealer Phone:
Notes:
Listing Label Information/Location The model information regarding your specific fireplace can be found on
the rating plate usually located in the control area of the fireplace.
GAS-FIRED
H E AT�G L O Heat 8 Glo,a brand of Hearth 8 Home Technologies,Inc.
No one builtls a better fire 7571 215th Street West,Lakeville,MN 55044 � u� ��
Type of Gas Not for use with solid fuel.
(Ne doit pas entre utilise avec un combustible solide). LI$TED
Type of Gas(Sorte De Gaz): This appliance must be installed in accordance with local codes,if any;if not,follow AN51 Z223.1
in the USA or CAN/CGA B149 installation codes.(Installerl'appareil selon les codes ou reglements
NATURAL GAS locaux ou,en 1'absence de tels reglements,selon les codes d'installation CAN/CGA-8149.J
Gas and Electric ANSIZ21XX-XXXX�CSA2.XX-MXX�UL307B
Information
Minimum Permissible Gas Supply for Purposes of Input Adjustment.
Approved Minimum(De Gaz)Acceptable 0.0 in w.c. (Po.Col.d'eau)
Maximum Pressure(Pression) 0.0 in w.c. (Po.Col.d'eau)
Maximum Manifold Pressure(Pression) 0.0 in w.c. (Po.Col.d'eau)
Minimum Manifold Pressure(Pression) 0.0 in w.c. (Po.Col.d'eau) Model Number
Total Electrical Requirements:OOOVac,OOHz.,less than 00 Amperes MADE IN USA l
INCANADA Mode�: Serial Number
ALTITUDE: 0-0000 FT. 0000-OOOOFT. (Modele): ��UU�
MAX.INPUTBTUH: 00,000 00,000
MIN.INPUT BTUH: 00,000 00,000
ORIFICESIZE: #XXXXX #XXXXX Serial
(Serie): ��UU�
2 Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12
A Safety Alert Key:
• DANGER!Indicates a hazardous situation which, if not avoided will result in death or serious injury.
• WARNING!Indicates a hazardous situation which, if not avoided could result in death or serious injury.
• CAUTION!Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
• NOTICE: Used to address practices not related to personal injury.
Table of Contents
A. Congratulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 6 Termination Locations
B. Limited Lifetime Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . 5 A. Vent Termination Minimum Clearances . . . . . . . . . . . . . . 25
1 Listing and Code Approvals 7 Vent Information and Diagrams
A. Appliance Certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 A. Approved Pipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
B. Tempered Glass Specifications . . . . . . . . . . . . . . . . . . . . . 7 B, Vent Table Ke 27
y. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
C. BTU Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 C. Use of Elbows 27
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
D. High Altitude Installations. . . . . . . . . . . . . . . . . . . . . . . . . . 7 D. Measuring Standards. . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
E. Non-Combustible Materials Specification. . . . . . . . . . . . . . 8 E. Vent Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
F. Combustible Materials Specification . . . . . . . . . . . . . . . . . 8
G. Electrical Codes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 8 Vent Clearances and Framing
H. Requirements for the Commonwealth of Massachusetts. . 9 A. Pipe Clearances to Combustibles . . . . . . . . . . . . . . . . . . 39
User Guide B• Wall Penetration Framing. . . . . . . . . . . . . . . . . . . . . . . . . 39
C. Install the Ceiling Firestop . . . . . . . . . . . . . . . . . . . . . . . . 40
2 Operating Instructions D. Install Attic Insulation Shield. . . . . . . . . . . . . . . . . . . . . . . 41
E. Installing the Optional Heat-Zone°Gas Kit . . . . . . . . . . . 41
A. Gas Fireplace Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
B. Your Fireplace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 g Appliance Preparation
C. Fan Kit(optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
D. ClearSpace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
A. Top Vent. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
E. Decorative Doors and Fronts. . . . . . . . . . . . . . . . . . . . . . 11
B. RearVent. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
F. Fixed Glass Assembl 11 C. Installing the Non-combustible Board. . . . . . . . . . . . . . . . 44
y . . . . . . . . . . . . . . . . . . . . . . . . .
G. Remote Controls, Wall Controls and Wall Switches. . . . . 11 D. Securing and Leveling the Appliance. . . . . . . . . . . . . . . . 44
H. IPI Battery Tray/Battery Installation . . . . . . . . . . . . . . . . . 12 10 Installing Vent Pipe (DVP and SLP Pipe)
I. Control Module Operation . . . . . . . . . . . . . . . . . . . . . . . . 12
J. Before Lighting Fireplace. . . . . . . . . . . . . . . . . . . . . . . . . �2 A. Assemble Vent Sections (DVP Pipe Only). . . . . . . . . . . . 45
K. Li htin Instructions IPI 13 B• Assemble Vent Sections (SLP Pipe Only) . . . . . . . . . . . . 46
9 9 � ) . . . . . . . . . . . . . . . . . . . . . . . . .
L. Li htin Instructions Standin Pilot 14 C. Assemble Slip Sections . . . . . . . . . . . . . . . . . . . . . . . . . . 46
9 9 � 9 ) . . . . . . . . . . . . . . . .
M. After Fireplace is Lit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 D. Secure the Vent Sections. . . . . . . . . . . . . . . . . . . . . . . . . 47
N. Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . . 15 E. Disassemble Vent Sections . . . . . . . . . . . . . . . . . . . . . . . 47
F. Install Decorative Ceiling Components(SLP only). . . . . . 48
3 Maintenance and Service G. Install Metal Roof Flashing. . . . . . . . . . . . . . . . . . . . . . . . 49
A. Maintenance Tasks-Homeowner . . . . . . . . . . . . . . . . . . . 16
H. Assemble and Install Storm Collar. . . . . . . . . . . . . . . . . . 49
B. Maintenance Tasks-Qualified Service Technician . . . . . . 17 I. Install Vertical Termination Cap . . . . . . . . . . . . . . . . . . . . 50
C. Refractory, Grate and Valve Assembly Removal . . . . . . . 18 J. Install Decorative Wall Components(SLP only). . . . . . . . 50
D. Burner ldentification/Verification. . . . . . . . . . . . . . . . . . . . 19
K. Heat Shield Requirements for Horizontal Termination . . . 50
L. Install Horizontal Termination Cap(DVP and SLP Pipe) . 51
Installer Guide
11 Gas Information
4 Getting Started A. Fuel Conversion. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
A. Typical Appliance System. . . . . . . . . . . . . . . . . . . . . . . . . 20 B. Gas Pressure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
B. Design and Installation Considerations . . . . . . . . . . . . . . 21 C. Gas Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
C. Tools and Supplies Needed . . . . . . . . . . . . . . . . . . . . . . . 21 D. High Altitude Installations. . . . . . . . . . . . . . . . . . . . . . . . . 52
D. InspectAppliance and Components. . . . . . . . . . . . . . . . . 21
12 Electrical Information
5 Framing and ClearanCes A. Wiring Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
A. Selecting Appliance Location. . . . . . . . . . . . . . . . . . . . . . 22 B. IntelliFire PIusT"' Ignition System Wiring . . . . . . . . . . . . . 53
B. Constructing the Appliance Chase. . . . . . . . . . . . . . . . . . 23 C. Standing Pilot Ignition System Wiring . . . . . . . . . . . . . . . 53
C. Clearances. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 D. Optional Accessories Requirements . . . . . . . . . . . . . . . . 53
D. Mantel and Wall Projections. . . . . . . . . . . . . . . . . . . . . . . 24 E. Electrical Service and Repair. . . . . . . . . . . . . . . . . . . . . . 55
Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12 3
F. Junction Box Installation. . . . . . . . . . . . . . . . . . . . . . . . . . 55
G. Wall Switch Installation for Fan (Optional). . . . . . . . . . . . 55
13 Finishing
A. Mantel and Wall Projections. . . . . . . . . . . . . . . . . . . . . . . 56
B. Facing Material. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
C. Doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
D. Elevated Hearth Systems. . . . . . . . . . . . . . . . . . . . . . . . . 60
14 Appliance Setup
A. Remove Fixed Glass Assembly. . . . . . . . . . . . . . . . . . . . 61
B. Remove the Shipping Materials. . . . . . . . . . . . . . . . . . . . 61
C. Clean the Appliance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
D. Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
� E. Burner Top Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
F. Ember Placement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
G. Install the Log Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . 62
H. Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
I. Install Trim and/or Surround. . . . . . . . . . . . . . . . . . . . . . . 66
J. Air Shutter Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
15 Troubleshooting
A. Standing Pilot Ignition System . . . . . . . . . . . . . . . . . . . . . 67
B. IntelliFire PIusT"' Ignition System . . . . . . . . . . . . . . . . . . . 69
16 Reference Materials
A. Appliance Dimension Diagram. . . . . . . . . . . . . . . . . . . . . 70
� B. Vent Components Diagrams . . . . . . . . . . . . . . . . . . . . . . 72
� C. Service Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
D. Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
� = Contains updated information.
4 Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12
B. Limited Lifetime Warranty
Hearth & Home Technologies Inc.
LIMITED LIFETIME WARRANTY
Hearth & Home Technologies Inc., on behalf of its hearth brands ("HHT"), extends the following warranty for
HHT gas, wood, pellet, coal and electric hearth appliances that are purchased from an HHT authorized dealer.
WARRANTY COVERAGE:
HHT warrants to the original owner of the HHT appliance at the site of installation, and to any transferee taking ownership
of the appliance at the site of installation within two years following the date of original purchase, that the HHT appliance
will be free from defects in materials and workmanship at the time of manufacture.After installation, if covered compo-
nents manufactured by HHT are found to be defective in materials or workmanship during the applicable warranty period,
HHT will, at its option, repair or replace the covered components. HHT, at its own discretion, may fully discharge all of its
obligations under such warranties by replacing the product itself or refunding the verified purchase price of the product
itself. The maximum amount recoverable under this warranty is limited to the purchase price of the product. This warranty
is subject to conditions, exclusions and limitations as described below.
WARRANTY PERIOD:
Warranty coverage begins on the date of original purchase. In the case of new home construction, warranty coverage
begins on the date of first occupancy of the dwelling or six months after the sale of the product by an independent,
authorized HHT dealer/distributor, whichever occurs earlier. The warranty shall commence no later than 24 months
following the date of product shipment from HHT, regardless of the installation or occupancy date. The warranty period for
parts and labor for covered components is produced in the following table.
The term "Limited Lifetime" in the table below is defined as: 20 years from the beginning date of warranty coverage for
gas appliances, and 10 years from the beginning date of warranty coverage for wood, pellet, and coal appliances. These
time periods reflect the minimum expected useful lives of the designated components under normal operating conditions.
Warranty Period HHT Manufactured Appliances and Venting
EPA Components Covered
Parts Labor Gas Wood Pellet Wood Coal Electric Venting
All parts and material except as
1 Year X X X X X X X covered by Conditions,
Exclusions, and Limitations
listed
X X X Igniters, electronic components,
2 years and lass
X X X X X Factor -installed blowers
X Molded refractor anels
3 ears X Fire ots and burn ots
5 ears 1 ear X X Castin s and baffles
7 years 3 years X X X Manifold tubes,
HHT chimne and termination
10 1 year X Burners, logs and refractory
ears
Limited 3 years X X X X X Firebox and heat exchanger
Lifetime
90 Days X X X X X X X All replacement parts
be ond warrant eriod
See conditions, exclusions, and limitations on next page.
4021-645C 12-29-10 Page 1 of 2
Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12 5
B. Limited Lifetime Warranty (continued)
WARRANTY CONDITIONS:
• This warranty only covers HHT appliances that are purchased through an HHT authorized dealer or distributor.A list of
HHT authorized dealers is available on the HHT branded websites.
• This warranty is only valid while the HHT appliance remains at the site of original installation.
• Contact your installing dealer for warranty service. If the installing dealer is unable to provide necessary parts, contact
the nearest HHT authorized dealer or supplier.Additional service fees may apply if you are seeking warranty service
from a dealer other than the dealer from whom you originally purchased the product.
• Check with your dealer in advance for any costs to you when arranging a warranty call. Travel and shipping charges
for parts are not covered by this warranty.
WARRANTY EXCLUSIONS:
This warranty does not cover the following:
• Changes in surface finishes as a result of normal use.As a heating appliance, some changes in color of interior and
exterior surFace finishes may occur. This is not a flaw and is not covered under warranty.
• Damage to printed, plated, or enameled surfaces caused by fingerprints, accidents, misuse, scratches, melted items,
or other external sources and residues left on the plated surfaces from the use of abrasive cleaners or polishes.
• Repair or replacement of parts that are subject to normal wear and tear during the warranty period. These parts
include: paint, wood, pellet and coal gaskets, firebricks, grates, flame guides, light bulbs, batteries and the discolor-
ation of glass.
• Minor expansion, contraction, or movement of certain parts causing noise. These conditions are normal and com-
plaints related to this noise are not covered by this warranty.
• Damages resulting from: (1)failure to install, operate, or maintain the appliance in accordance with the installation
instructions, operating instructions, and listing agent identification label furnished with the appliance; (2)failure to
install the appliance in accordance with local building codes; (3)shipping or improper handling; (4) improper opera-
tion, abuse, misuse, continued operation with damaged, corroded or failed components, accident, or improperly/
incorrectly performed repairs; (5) environmental conditions, inadequate ventilation, negative pressure, or drafting
caused by tightly sealed constructions, insufficient make-up air supply, or handling devices such as exhaust fans or
forced air furnaces or other such causes; (6) use of fuels other than those specified in the operating instructions; (7)
installation or use of components not supplied with the appliance or any other components not expressly authorized
and approved by HHT; (8) modification of the appliance not expressly authorized and approved by HHT in writing;
and/or(9) interruptions or fluctuations of electrical power supply to the appliance.
• Non-HHT venting components, hearth components or other accessories used in conjunction with the appliance.
• Any part of a pre-existing fireplace system in which an insert or a decorative gas appliance is installed.
• HHT's obligation under this warranty does not extend to the appliance's capability to heat the desired space. Informa-
tion is provided to assist the consumer and the dealer in selecting the proper appliance for the application. Consider-
ation must be given to appliance location and configuration, environmental conditions, insulation and air tightness of
the structure.
This warranty is void if:
• The appliance has been over-fired or operated in atmospheres contaminated by chlorine, fluorine, or other damaging
chemicals. Over-firing can be identified by, but not limited to, warped plates or tubes, rust colored cast iron, bubbling,
cracking and discoloration of steel or enamel finishes.
• The appliance is subjected to prolonged periods of dampness or condensation.
• There is any damage to the appliance or other components due to water or weather damage which is the result of, but
not limited to, improper chimney or venting installation.
LIMITATIONS OF LIABILITY:
• The owner's exclusive remedy and HHT's sole obligation under this warranty, under any other warranty, express or
implied, or in contract, tort or otherwise, shall be limited to replacement, repair, or refund, as specified above. In no
event will HHT be liable for any incidental or consequential damages caused by defects in the appliance. Some states
do not allow exclusions or limitation of incidental or consequential damages, so these limitations may not apply to you.
This warranty gives you specific rights; you may also have other rights, which vary from state to state. EXCEPT TO
THE EXTENT PROVIDED BY LAW, HHT MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY
SPECIFIED HEREIN. THE DURATION OF ANY IMPLIED WARRANTY IS LIMITED TO DURATION OF THE
EXPRESSED WARRANTY SPECIFIED ABOVE.
4021-645C 12-29-10 Page 2 of 2
6 Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12
1 Listing and Code Approvals
A. Appliance Certification C. BTU Specifications
Models Maximum Minimum Orifice
MODELS:6000C, 6000C-IPI, 8000C, 8000C-IPI �nput Input Size
(U.S. or Canada) BTU/h BTU/h (DMS)
LABORATORY:Underwriters Laboratories, Inc. (UL)
TYPE:Direct Vent Gas Appliance Heater 6000C(NG) (0-200o Fr� 30,000 16,000 s�
STANDARD:ANSI Z21.88b-2008•CSA 2.33a-2008 6000C-IPI (NG) CANADA
(2000-4500 FT) 2�,000 14,400 38
US 2g,000 17,000 52
This product is listed to ANSI standards for "Vented Gas 6000C-LP �o-ZOOO Fr�
Appliance Heaters"and applicable sections of"Gas Burn- 6000C-IPILP CANADA 26,�00 15,soo 53
ing Heating Appliances for Manufactured Homes and (2000-4500FT)
Recreational Vehicles", and "Gas Fired Appliances for g000C (NG) � - US 35,000 �s,000 3s
Use at High Altitudes". 0 200o Fr�
8000C-IPI (NG) CANADA 31,500 17,100 34
NOTICE: This installation must conform with local codes. �z000-a5oo Fr�
In the absence of local codes you must comply with the g000C-LP (0-200o Fr) 3a,000 ��,000 so
National Fuel Gas Code, ANSI Z223.1-latest edition in g000C-IPILP CANADA
the U.S.A. and the CAN/CGA B149 Installation Codes in (2000-4500 FT) 30,600 15,300 51
Canada.
D. High Altitude Installations
NOT INTENDED FOR USE AS A PRIMARY HEAT SOURCE.
This appliance is tested and approved as either supplemen- NOTICE:If the heating value of the gas has been reduced,
tal room heat or as a decorative appliance. It should not be these rules do not apply. Check with your/ocal gas utility
factored as primary heat in residential heating calculations. or authorities having jurisdiCtion.
When installing above 2000 feet elevation:
B. Tempered Glass Specifications • In the USA: Reduce input rate 4% for each 1000 feet
Hearth & Home Technologies appliances manufactured above 2000 feet.
with tempered glass may be installed in hazardous loca- • In CANADA: Reduce input rate 10% for elevations
tions such as bathtub enclosures as defined by the Con- between 2000 feet and 4500 feet. Above 4500 feet,
sumer Product Safety Commission(CPSC).The tempered consult local gas utility.
glass has been tested and certified to the requirements
of ANSI Z97.1 and CPSC 16 CFR 1202 (Safety Glazing Check with your local gas utility to determine proper
Certification Council SGCC# 1595 and 1597.Architectur- orifice size.
al Testing, Inc. Reports 02-31919.01 and 02-31917.01).
This statement is in compliance with CPSC 16 CFR Sec-
tion 1201.5 "Certification and labeling requirements"
which refers to 15 U.S. Code (USC)2063 stating "...Such
certificate shall accompany the product or shall otherwise
be furnished to any distributor or retailer to whom the
product is delivered."
Some local building codes require the use of tempered
glass with permanent marking in such locations. Glass
meeting this requirement is available from the factory.
Please contact your dealer or distributor to order.
Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12 7
E. Non-Combustible Materials Specification
Material which will not ignite and burn. Such materials are
those consisting entirely of steel, iron, brick,tile, concrete,
slate, glass or plasters, or any combination thereof.
Materials that are reported as passing ASTM E 136,
Standard Test Method for Behavior of Materials in a
Vertical Tube Furnace at 750 °C and UL763 shall be
considered non-combustible materials.
F. Combustible Materials Specification
Materials made of or surfaced with wood, compressed pa-
per, plant fibers, plastics, or other material that can ignite
and burn, whether flame proofed or not, or plastered or
unplastered shall be considered combustible materials.
G. Electrical Codes
NOTICE: This appliance must be electrically wired and
grounded in accordance with local codes or,in the absence
of local codes, with National Electric Code ANSI/NFPA
70-latest edition or the Canadian Electric Code CSA
C22.1.
• A 110-120 VAC circuit for this product must be protected
with ground-fault circuit-interrupter protection,in compliance
with the applicable electrical codes, when it is installed in
locations such as in bathrooms or near sinks.
8 Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12
Inspection
Note: The following requirements reference various
Massachusetts and national codes not contained in this The state or local gas inspector of the side wall horizon-
document. tally vented gas fueled equipment shall not approve the
installation unless, upon inspection, the inspector ob-
H. Re uirements for the Commonwealth of serves carbon monoxide detectors and signage installed
p in accordance with the provisions of 248 CMR 5.08(2)(a)1
Massachusetts through 4.
For all side wall horizontally vented gas fueled equipment Exemptions
installed in every dwelling, building or structure used in
whole or in part for residential purposes, including those The following equipment is exempt from 248 CMR
owned or operated by the Commonwealth and where the 5.08(2)(a)1 through 4:
side wall exhaust vent termination is less than seven (7) . The equipment listed in Chapter 10 entitled "Equipment
feet above finished grade in the area of the venting, in- Not Required To Be Vented" in the most current edition
cluding but not limited to decks and porches,the following of NFPA 54 as adopted by the Board; and
requirements shall be satisfied:
• Product Approved side wall horizontally vented gas fu-
Installation of Carbon Monoxide Detectors eled equipment installed in a room or structure separate
At the time of installation of the side wall horizontal vented from the dwelling, building or structure used in whole or
gas fueled equipment, the installing plumber or gas fitter in part for residential purposes.
shall observe that a hard wired carbon monoxide detector
with an alarm and battery back-up is installed on the floor MANUFACTURER REQUIREMENTS
level where the gas equipment is to be installed. In addi- Gas Equipment Venting System Provided
tion, the installing plumber or gas fitter shall observe that
a battery operated or hard wired carbon monoxide detec- When the manufacturer of Product Approved side wall
tor with an alarm is installed on each additional level of horizontally vented gas equipment provides a venting
the dwelling, building or structure served by the side wall system design or venting system components with the
horizontal vented gas fueled equipment. It shall be the equipment, the instructions provided by the manufacturer
responsibility of the property owner to secure the services for installation of the equipment and the venting system
of qualified licensed professionals for the installation of shall include:
hard wired carbon monoxide detectors.
• Detailed instructions for the installation of the venting
In the event that the side wall horizontally vented gas fu- system design or the venting system components; and
eled equipment is installed in a crawl space or an attic, • A complete parts list for the venting system design or
the hard wired carbon monoxide detector with alarm and venting system.
battery back-up may be installed on the next adjacent
floor level. Gas Equipment Venting System NOT Provided
In the event that the requirements of this subdivision can �/hen the manufacturer of a Product Approved side wall
not be met at the time of completion of installation, the
owner shall have a period of thirty (30) days to comply horizontally vented gas fueled equipment does not pro-
with the above requirements; provided, however,that dur- vide the parts for venting the flue gases, but identifies
ing said thirty (30) day period, a battery operated carbon "special venting systems", the following requirements
monoxide detector with an alarm shall be installed. shall be satisfied by the manufacturer:
Approved Carbon Monoxide Detectors • The referenced "special venting system" instructions
shall be included with the appliance or equipment in-
Each carbon monoxide detector as required in accor- stallation instructions; and
dance with the above provisions shall comply with NFPA
720 and be ANSI/UL 2034 listed and IAS certified. • The "special venting systems" shall be Product Ap-
proved by the Board, and the instructions for that sys-
Signage tem shall include a parts list and detailed installation
A metal or plastic identification plate shall be permanent- instructions.
ly mounted to the exterior of the building at a minimum
height of eight(8)feet above grade directly in line with the A copy of all installation instructions for all Product Ap-
exhaust vent terminal for the horizontally vented gas fu- proved side wall horizontally vented gas fueled equip-
eled heating appliance or equipment. The sign shall read, ment, all venting instructions, all parts lists for venting
in print size no less than one-half (1/2) in. in size, "GAS instructions, and/or all venting design instructions shall
VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OB- remain with the appliance or equipment at the completion
STRUCTIONS". of the installation.
See Gas Connection section for additional Common-
wealth of Massachusetts requirements.
Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12 9
2 Operating Instructions User Guide
A. Gas Fireplace Safety • Keep remote controls out of reach of children.
• Never leave children alone near a hot fireplace,whether
A WARNING operating or cooling down.
HOT SURFACES! • Teach children to NEVER touch the fireplace.
` Glass and other surfaces are hot during • Consider not using the fireplace when children will be
operation AND cool down. present.
� Hot glass will cause burns. Contact your dealer for more information, or visit: www.
• DO NOT touch glass until it is cooled �ba.org/safety-information.
• NEVER allow children to touch glass
• Keep children away To prevent unintended operation when not using your fire-
• CAREFULLY SUPERVISE children in same room as place for an extended period of time (summer months,
fireplace. vacations, trips, etc):
• Alert children and adults to hazards of high temperatures.
High temperatures may ignite clothing or other ' Remove batteries from remote controls.
flammable materials. • Turn off wall controls.
• Keep clothing, furniture, draperies and other flammable . Unplug 6 volt transformer plug and remove batteries on
materials away. IPI models.
This appliance has been supplied wifh an integral barrier • Turn off gas controls valve on standing pilot models.
to prevent direct contact with the fixed g/ass panel. DO
NOT operate the appliance with the barrier removed. When lighting the pilot light on fireplaces with a standing
Contact your dealer or Hearth & Home Technologies if the pilot, remove the fixed glass assembly so you can de-
barrier is not present or help is needed to properly install one. tect presence of residual gas build-up. See Standing Pilot
Lighting instructions and Maintenance Tasks.
If you expect that small children or vulnerable adults may
come into contact with this fireplace,the following precau- B. Your Fireplace
tions are recommended:
WARNING! DO NOT operate fireplace before read-
• Install a physical barrier such as: ing and understanding operating instructions. Failure
- A decorative firescreen. to operate fireplace according to operating instructions
- Adjustable safety gate. could cause fire or injury.
• Install a switch lock or a wall/remote control with child
protection lockout feature.
�\
�
DECORATNEDOORS
\��
(NOTSHOWN� �
SECTION 2.E. \
� FIXEOGLASSA95EMBLV �
\\(NOTSHOWN) �
SECTION 14.H.
\
\ \
\ \�R
\T 1
i x
� � ��
MANTEL
/ FAN KIT � SECTION S.D
� SECTION 2.C.
\ \
\ \
\ \ HEARTH \
\\
CLEAR SPAC\
\ECTION 2.D.
%
\\� \..GRATE �/
\ SECTION 3.C.//
Figure 2.1 General Operating Parts ���
10 Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12
C. Fan Kit (optional) G. Remote Controls, Wall Controls and Wall
If desired, a fan kit may be added. Contact your dealer to SWItCheS
order the correct fan kit. Follow the instructions supplied with the control installed
D. Clear Space to operate your fireplace:
For safety:
W�IRNING! DO NOT place combustible objects in front
of the fireplace or block louvers. High temperatures may • Install a switch lock or a wall/remote control with child
start a fire. See Figure 2.2. protection lockout feature.
Avoid placing candles and other heat-sensitive objects on • Keep remote controls out of reach of children.
mantel or hearth. Heat may damage these objects. See your dealer if you have questions.
��^�
\�
�
�
/ �
� \ �T� O
� '�NF<Fq���
� R�N RSa �.
\\ TpF,'9C� l•
iRFp�
cF�
\
\� �
Figure 2.2 Clear Space ��
E. Decorative Doors and Fronts
WARNING! Risk of Fire! Install ONLY doors or fronts
approved by Hearth & Home Technologies. Unapproved
doors or fronts may cause fireplace to overheat.
This fireplace has been supplied with an integral
barrier to prevent direct contact with the fixed g/ass
panel. DO NOT operate the fireplace with the barrier
removed.
Contact your dealer or Hearth & Home Technologies if
the barrier is not present or help is needed to properly
install one.
For more information refer to the instructions supplied with
your decorative door or front.
F. Fixed Glass Assembly
See Section 14.H.
Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12 11
H. IPI Battery Tray/Battery Installation
The IntelliFire PlusT"^system has a battery backup option. �
Battery longevity and performance will be affected by the °
service temperatures of this appliance. ��m ��
NOTICE: Batteries should only be used as a power source
in the event of an emergency such as an outage. se�ecTOR
SWITCH
I. Control Module Operation �
� �
1. The control module has an ON/OFF/REMOTE selector -
switch that must be set. See Figure 2.3. ������� °
� °�° ��� �
OFF Position: Appliance will ignore all power � ���� Oo OO ���
inputs and will not respond to any commands from
a wall switch or remote. The unit should be in the / STATUS INDICATOR LED �
OFF position during installation, service, battery FLAME HI/LO SWITCH NG/LP SETTING
installation, and in the event that the control goes (RC100 OR WIRED WALL SWITCH ONLY)
into LOCK-OUT mode as a result of an error code. Figure 2.s controi nnoduie
ON Position: Appliance will ignite and run
continuously in the HI flame setting, with no • Locate the module selector switch. (SeeFigure 2.3).
adjustment in flame output. This mode of operation
is primarily used for initial installation or power • Set the module selector switch to the OFF position.
outage operation with battery backup. • Wait five(5)minutes to allow possible accumulated gas
REMOTE Position: Appliance will initiate to clear.
commands from an optional wired wall switch and/ • Set the module selector switch to the ON or REMOTE
or the wireless remote (RC300). position.
2. If using a wired wall switch with the module in REMOTE • Start the appliance.
mode, the flame output can be adjusted with the HI/ yyqRNING!Risk of Explosion!DO NOT reset the mod-
LO selector switch on the module. See Figure 2.3. ule more than one time within a five minute time period.
Note that the flame HI/LO selector switch will become Gas may accumulate in firebox. Call a qualified service
inactive once an optional remote control (RC200/ technician.
RC300) is programmed to the control module. Note
that the control module will always ignite the fireplace Nine Hour Safety Shutdown Feature
on HI and remain so for the initial 10 seconds of This appliance has a safety feature that automatically
operation. If the HI/LO is switched to the LO position, shuts down the fireplace after 9 hours of continuous
the flame output will automatically drop to the lowest operation without receiving a command from the
setting after the flame has been established for 10 sec. remote.
After this 10 second period,the flame can be adjusted
from HI to LO with the switch.
3. Thecontrolmodulehassafetyfeaturethatautomatically J. Before Lighting Fireplace
shuts down the fireplace after 9 hours of continuous gefore operating this fireplace for the first time, have a
operation without receiving a command from the qualified service technician:
remote.
4. If you intend to use both a wired wall switch and the ' Verify all shipping materials have been removed from
RC300 remote control to operate your fireplace, the inside and/or underneath the firebox.
wall switch will override any commands given by the • Review proper placement of logs, ember material and/
remote. or other decorative materials.
5. Module Reset • Ensure plastic finishing strips have been removed after
This module may lock-out under certain conditions.
use for incorporating finishing materials.
When this occurs, the appliance will not ignite or • Check the wiring.
respond to commands. The module will go into • Check the air shutter adjustment.
lock-out mode by emitting three audible beeps, then
continuously displaying a RED/GREEN error code at ' Ensure that there are no gas leaks.
its status indicator LED. • Ensure that the glass is sealed and in the proper position
• Check battery tray. Remove batteries if installed. and that the integral barrier is in place.
Batteries should only be installed for use during power Wi4RNING! Risk of Fire orAsphyxiation!DO NOT op-
outages. See Section H. erate fireplace with fixed glass assembly removed.
12 Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12
K. Lighting Instructions (IPI)
FOR YOUR SAFETY 0 LIGHTING 0
READ BEFORE LIGHTING INSTRUCTIONS (IPI)
WARNING: Ifyoudonotfollowtheseinstructionsexactly,afireorexplosion 1. This appliance is equipped with an ignition
may result causing property damage, personal injury or loss of life. device which automatically lights the burner.
DO NOT try to light the burner by hand.
A.This appliance is equipped with an • Immediately call your gas supplier
intermittent pilot ignition(IPI)device from a neighbor's phone. Follow the � O O
which automatically lights the burn- gas supplier's instructions.
er.DO NOT try to light the burner by . If you cannot reach your gas sup- GAS O � O
hand. VALVE
plier, call the fire department. o
B. BEFORE LIGHTING,smell all around C.DO NOT use this appliance if any �
the appliance area for gas. Be sure to part has been under water. Imme-
smell next to the floor because some 2. Wait five (5) minutes to clear out any gas.
gas is heavier than air and will settle diately call a qualified service tech- g g
nician to inspect the appliance and Then smell for as, includin near the floor. If
on the floor. to replace any part of the control You smell gas, STOP! Follow"B"in the Safety
WHAT TO DO IF YOU SMELL GAS system and any gas control which Information located on the left side of this la-
• DO NOT try to light any appliance.
has been under water. bel. If you do not smell gas, go to next step.
3. To light the burner:
• DO NOT touch any electric switch; do Equipped with wall switch:Turn ON/OFF switch
not use any phone in your building. to ON.
WA R N I N G : CA U T I O N ■ Equipped with remote or wall control: Press
ON or FLAME button.
Equipped with thermostat:Set temperature to
DO NOT CONNECT LINE VOLT- Hot while in operation. DO NOT touch. desired setting.
AGE (110/120 VAC OR 220/240 Keep children,clothing,furniture,gaso- 4. If the appliance does not light after three tries,
VAC)TO THE CONTROL VALVE. line and other liquids having flammable call your service technician or gas supplier.
vapors away.
Improper installation, adjustment, al-
teration, service or maintenance can DO NOT operate the appliance with 0 TO TURN OFF 0
cause injury or property damage. Re- fixedglassassemblyremoved,cracked GAS TO APPLIANCE
fer to the owner's information manual or broken. Replacement of the fixed
provided with this appliance. glass assembly should be done by a 1. Equipped with wall switch:Turn ON/OFF switch
licensed or qualified service person. to OFF.
This appliance needs fresh air for
safe operation and must be installed NOT FOR USE Equipped with remote or wall control: Press
so there are provisions for adequate WITH SOLID FUEL OFF button.
combustion and ventilation air. Equipped with thermostat: Set temperature to
If not installed, operated, and main- For use with natural gas and propane. lowest setting.
tained in accordance with the manufac- A conversion kit, as supplied by the 2, Service technician should turn off electric
turer's instructions, this product could manufacturer,shall be used to convert power to the control when performing service.
expose you to substances in fuel or this appliance to the alternate fuel.
fuel combustion which are known to the Also Certified for Installation in a
State of California to cause cancer,birth 593-913G
Bedroom or a Bedsitting Room.
defects,or other reproductive harm.
Keep burner and control compartment For assistance or additional informa-
tion, consult a qualified installer, ser-
clean. See installation and operating vice agency or the gas supplier.
instructions accompanying appliance.
For additional information on operating your
Hearth&Home Technologies fireplace,please refer to www.fireplaces.com.
Final inspection by
Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12 13
L. Lighting Instructions (Standing Pilot)
FOR YOUR SAFETY O LIGHTING O
READ BEFORE LIGHTING INSTRUCTIONS
1. Open control access panel.
WARN I NG: If you do not follow these instructions exactly,a fire or explosion 2, Turn off all electric power to °o°e
may result causing property damage, personal injury or loss of life. the appliance. � ° ��
�
A.This appliance has a pilot which • If you cannot reach your gas sup- 3. Push in gas control knob �� � �oo
must be lighted by hand. When plier, call the fire department. slightly and turn clockwise
�� to"OFF".
lighting the pilot, follow these in- C. Use only your hand to push in or
structions exactly. turn the gas control knob.Never use Note: Knob cannot be turned from "PILOT" to "OFF"
B. BEFORE LIGHTING,smell all around tools. If the knob will not push in or unless knob is pushed in slightly. DO NOT force.
the appliance area for gas. Be sure to turn by hand, DO NOT try to repair 4. Open the fixed glass assembly. You may need to
smell next to the floor because some it, call a qualified service technician. remove the decorative front.
gas is heavier than air and will settle Force or attempted repair may re- 5. Wait five (5) minutes to clear out any gas. Then
on the floor. sult in a fire or explosion. smell for gas, including near the floor. If you smell
WHAT TO DO IF YOU SMELL GAS D. DO NOT use this appliance if any gas,STOP!Follow"B"in the Safety
Information located on the left side
• DO NOT try to light any appliance. part has been under water. Imme- of this label. If you don't smell gas,
diately call a qualified service tech- go to next step.
• DO NOT touch any electric switch;do nician to inspect the appliance and 6. Find the pilot. The pilot is inside
not use any phone in your building. to replace any part of the control combustion chamber next to the
• Immediately call your gas supplier system and any gas control which main burner
from a neighbor's phone. Follow the has been under water. 7. Turn knob on gas control counterclockwise ►��
gas supplier's instructions. to"PILOT".
8. Push in control knob all the way and hold in.Immedi-
WA R N I N G : CA U T I O N ■ ately depress red or black piezo button.It may require
several depressions of the red or black piezo button
until PILOT lights. If PILOT light does not light after
10 seconds, return to step 3. Continue to hold the
DO NOT CONNECT 110 VAC TO Hot while in operation.DO NOT touch. control knob in for about one minute afterthe pilot is
THE CONTROL VALVE. Keep children,clothing,furniture,gaso- lit.Release knob and it will pop back out.Pilot should
line and other liquids having flammable remain lit. If it goes out,repeat steps 3 through 6.
Improper installation, adjustment, al- vapors away. • If knob does not pop up when released,stop and
teration, service or maintenance can
cause injury or property damage. Re- DO NOT operate the appliance with immediately call your service technician or gas
fer to the owner's information manual fixed glass assembly removed,cracked supplier.
provided with this appliance. or broken. Replacement of the fixed • If the pilot will not stay lit after several tries, turn
glass assembly should be done by a the gas control knob to "OFF" and call your ser-
This appliance needs fresh air for licensed or qualified service person. vice technician or gas supplier.
safe operation and must be installed 9. Reinstall fixed glass assembly. Reinstall decorative
so there are provisions for adequate NOT FOR USE front.
combustion and ventilation air. W�TH SOLID FUEL g
10.Turn as control knob counterclockwise��
If not installed, operated, and main- to"ON". Close access panel.
tained in accordance with the man- For use with natural gas and propane. 11. Turn on all electric power to the appliance.
ufacturer's instructions, this product A conversion kit, as supplied by the 12. To light burner,turn the wall control or on/off switch
could expose you to substances in fuel manufacturer,shall be used to convert to"ON".
or fuel combustion which are known to this appliance to the alternate fuel.
the State of California to cause can- 0 TO TURN OFF 0
cer,birth defects,or other reproductive Also Certified for Installation in a
harm. Bedroom or a Bedsitting Room. GAS '�"0 APPL�ANCE
Keep burner and control compartment For assistance or additional informa- 1. Turn off all electric power to the appliance if ser-
tion, consult a qualified installer, ser- vice is to be erformed.
clean. See installation and operating vice agency or the gas supplier. p
instructions accompanying appliance. 2. Open control access panel.
For additional information on operating your 3. Move switch to"OFF"position.
Hearth&Home Technologies fireplace, please refer to www.fireplaces.com. 4. Push in gas control knob slightly and turn clock-
wise ��,to OFF". DO NOT force.
5. Close control access panel.
Final inspection by
464-903H
14 Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12
M. After Fireplace is Lit
Initial Break-in Procedure
• The fireplace should be run three to four hours
continuously on high.
• Turn the fireplace off and allow it to completely cool.
• Remove fixed glass assembly. See Section 14.H.
• Clean fixed glass assembly. See Section 3.
• Replace the fixed glass assembly and run continuously
on high an additional 12 hours.
This cures the materials used to manufacture the fire-
place.
NOTICE!Open windows for air circulation during fire-
p/ace break-in.
• Some people may be sensitive to smoke and odors.
• Smoke detectors may activate.
N. Frequently Asked Questions
ISSUE SOLUTIONS
Condensation on the glass This is a result of gas combustion and temperature variations.As the appliance warms, this
condensation will disappear.
Blue flames This is a result of normal operation and the flames will begin to yellow as the appliance is al-
lowed to burn for 20 to 40 minutes.
When first operated,this appliance may release an odor for the first several hours.This is caused
Odor from appliance by the curing of the paint and the burning off of any oils remaining from manufacturing.Odor may
also be released from finishing materials and adhesives used around the appliance.
This is a normal result of the curing process of the paint and logs. Glass should be cleaned
Film on the glass within 3 to 4 hours of initial burning to remove deposits left by oils from the manufacturing
process.A non-abrasive cleaner such as gas fireplace glass cleaner may be necessary. See
your dealer.
Noise is caused by metal expanding and contracting as it heats up and cools down, similar to
Metallic noise the sound produced by a furnace or heating duct. This noise does not affect the operation or
longevity of the appliance.
Is it normal to see the pilot flame burn In an intermittent pilot ignition system (IPI), the pilot flame should turn off when appliance is
continually? turned off. Some optional control systems available with IPI models may allow pilot flame to
remain lit. In a standing pilot system the pilot will always stay on.
Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12 15
3 Maintenance and Service
Any safety screen or guard removed for servicing must be �OOPS, Surrounds, Fronts
replaced prior to operating the fireplace. Frequency: Annually
When properly maintained, your fireplace will give you BY� Homeowner
many years of trouble-free service. We recommend an- Tools needed: Protective gloves, stable work surface
nual service by a qualified service technician. • Assess condition of screen and replace as necessary.
A. Maintenance Tasks-Homeowner • Inspect for scratches, dents or other damage and repair
as necessary.
Installation and repair should be done by a qualified service
technician only. The fireplace should be inspected before • CheCk that louvers are not bloCked.
use and at least annually by a professional service person.
• Vacuum and dust surfaces.
The following tasks may be performed annually by the
homeowner. If you are uncomfortable performing any of Remote Control
the listed tasks, please call your dealer for a service ap- Frequency: Seasonally
pointment.
By: Homeowner
More frequent cleaning may be required due to lint from Tools needed: Replacement batteries and remote con-
carpeting or other factors. Control compartment, burner trol instructions.
and circulating air passageway of the fireplace must be
kept clean. • Locate remote control transmitter and receiver.
CAUTION!Risk ofBurns!The fireplace should be turned • Verify operation of remote. Refer to remote control
off and cooled before servicing. operation instructions for proper calibration and setup
Glass Cleaning procedure.
• Place batteries as needed in remote transmitters and
Frequency: Seasonally battery-powered receivers.
By: Homeowner • Place remote control out of reach of children.
Tools Needed: Protective gloves, glass cleaner, drop If not using your fireplace for an extended period of time
cloth and a stable work surface. (summer months, vacations/trips, etc), to prevent unin-
CAUTION! Handle fixed g/ass assembly with care. tended operation:
G/ass is breakable. • Remove batteries from remote controls.
• Avoid striking, scratching or slamming g/ass
• Avoid abrasive cleaners • Unplug 6 volt transformer plug on IPI models.
• DO NOT clean glass while it is hot • Unplug battery backup from control module.
• Prepare a work area large enough to accommodate fixed
glass assembly and door frame by placing a drop cloth
on a flat, stable surface.
Note: Fixed glass assembly and gasketing may have res-
idue that can stain carpeting or floor surFaces.
• Remove door or decorative front from fireplace and set
aside on work surface.
• See Section 14.H for instructions to remove fixed glass
assembly.
• Clean glass with a non-abrasive commercially available
cleaner.
- Light deposits: Use a soft cloth with soap and water
- Heavy deposits: Use commercial fireplace glass
cleaner(consult with your dealer)
• Carefully set fixed glass assembly in place on fireplace.
Hold glass in place with one hand and secure glass
latches with the other hand.
• Reinstall door or decorative front.
16 Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12
Venting • Replace fireplace if firebox has been perforated.
Frequency: Seasonally Control Compartment and Firebox Top
By: Homeowner Frequency: Annually
Tools needed: Protective gloves and safety glasses. By: Qualified Service Technician
• Inspect venting and termination cap for blockage or Tools needed: Protective gloves, vacuum cleaner, dust
obstruction such plants, bird nests, leaves,snow,debris, cloths
etc. • Vacuum and wipe out dust, cobwebs, debris or pet hair.
• Verify termination cap clearance to subsequent construc- Use caution when cleaning these areas. Screw tips that
tion (building additions, decks, fences, or sheds). See have penetrated the sheet metal are sharp and should
Section 6. be avoided.
• Inspect for corrosion or separation. • Remove all foreign objects.
• Verify weather stripping, sealing and flashing remains • Verify unobstructed air circulation.
intact.
• Inspect draft shield to verify it is not damaged or missing. BuP11eP Ig111t1011 alld Oper'at1011
Frequency: Annually
B. Maintenance Tasks-Qualified Service gy; Qualified Service Technician
Technician
Tools needed: Protective gloves, vacuum cleaner, whisk
The following tasks must be performed by a qualified ser- broom, flashlight, voltmeter, indexed drill bit set, and a
vice technician. manometer.
Gasket Seal and Glass Assembly Inspection • Verify burner is properly secured and aligned with pilot
Frequency: Annually or igniter.
By: Qualified Service Technician • Clean off burner top, inspect for plugged ports,corrosion
or deterioration. Replace burner if necessary.
Tools needed: Protective gloves, drop cloth and a stable
work surFace. • Replace Glowing embers with new dime-size pieces.
DO NOT block ports or obstruct lighting paths. Refer to
• Inspect gasket seal and its condition. Section 14 for proper ember placement.
• Inspect fixed glass assembly for scratches and nicks that • Verify batteries have been removed from battery back-
can lead to breakage when exposed to heat. up IPI systems to prevent premature battery failure or
• Confirm there is no damage to glass or glass frame. leaking.
Replace as necessary. • Check for smooth lighting and ignition carryover to all
• Verify that fixed glass assembly is properly retained and ports. Verify that there is no ignition delay.
attachment components are intact and not damaged. • Inspect for lifting or other flame problems.
Replace as necessary.
• Verify air shutter setting is correct. See Section 14 for
Logs required air shutter setting. Verify air shutter is clear of
dust and debris.
Frequency: Annually
• Inspect orifice for soot, dirt and corrosion. Verify orifice
By: Qualified Service Technician size is correct. See Service Parts List for proper orifice
Tools needed: Protective gloves. sizing.
• Inspect for damaged or missing logs. Replace as neces- • Verify manifold and inlet pressures.Adjust regulator as
sary. Refer to Section 14 for log placement instructions. required.
• Verify correct log placement and no flame impingement • Inspect pilot flame pattern and strength.See Figures 3.1
causing sooting. Correct as necessary. and 3.2 for proper pilot flame pattern. Clean or replace
Firebox orifice spud as necessary.
• Inspect thermocouple/thermopile or IPI flame sensing
Frequency: Annually rod for soot,corrosion and deterioration. Polish with fine
By: Qualified Service Technician steel wool or replace as required.
Tools needed: Protective gloves, sandpaper, steel wool, • Verify thermocouple/thermopile millivolt output. Replace
cloths, mineral spirits, primer and touch-up paint. pilot as necessary. (Standing pilot only)
• Inspect for paint condition, warped surfaces, corrosion • Verify that there is not a short in flame sense circuit
or perforation. Sand and repaint as necessary. by checking continuity between pilot hood and flame
sensing rod. Replace pilot as necessary. (IPI only)
Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12 17
4
I
�
1'
f
�
i
� .�� � ���� -_�__ 4
� � v
`i
T �
.,��" o 0 0°\
� o �o
� \ �o
�..
Figure 3.1 IPI Pilot Flame Patterns �.
T.
\ �
, � , .�r � �4 �
��'��� ,���I+I�� �� ���i�'4�d� t 4f �'��t y°�p t )�i��fy� ;.' i /�._ '
�'U,Pr 4�. �! � ��� ��t}�`(`.°�`�i 3 �� t.,' ��-.
! i �r��._ ,.:,r., � ;.� '
2
9
- _ yq�,���„E�i��`-,
.,�.
� '''"`�' �; ,i�' � Figure 3.3 Grate Removal
,,
_ �;
� � �
i, � � �
C��� 4� '
�
� Note:The base refractory must be
'�� � : s' removed to access screws.
t�?i�i=�
� ��\
- '�� BASE REFRACTORY
Figure 3.2 Standing Pilot Flame Patterns T,
C. Refractory, Grate and Valve Assembly ��-�.
Removal �
.�
It may become necessary to remove the refractory, grate � ��
and valve assemblies. This task should be performed by
a qualified service technician. The grate and base refrac- �
tory do not need to be removed to service the burner �
assembly.
•
�
�
0 0
- o��oo
. o 00
. 8
Figure 3.4 Base Refractory Removal
18 Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12
4
4
i
/
4 � 4
. 4 � t
8 4 \
T
� a�
� - . -
� "
Figure 3.5 Valve Assembly Removal �
D. Burner ldentification/Verification
The burner may be accessed for identification and verification purposes. This task should be performed by a qualified ser-
vice technician. The base refractory, valve plate and grate do not need to be removed to access the burner assembly. The
logs and fiber burner top need to be removed to access the burner. Disconnect the pilot from the burner before removal.
See Figure 3.6 for burner identification chart. Notch patterns are located on bottom side of burner.
NOTCH LOCATION
�
� �
� � ��
�\
���
/ �
e
�
/�
��/
/
NG LP � �f�
6000C �r —1-1— �
6000CL �� �L� %/�
6000CLX �r —L�L�
6000CBV �r Z�
8000C �r �—
8000CL �— ��
8000CLX �r
8000CBV �r ��
Figure 3.6 Burner ldentification
Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12 19
4 Getting Started �nstaller Guide
A. Typical Appliance System
NOTICE: lllustrations and photos reflect typical installations and are for design purposes only. lllustrations/diagrams are not
drawn to scale.Actual product may vary from pictures in manual
HORIZONTAL
Note: Dual ventin C011fl urations TERMINATIONCAP
9 9 (SECTION 10.L)
ARE NOT allowed. Appliance MUST
be vented EITHER vertically OR �
horizontally.
VERTICAL TERMINATION CAP
(SECTION 70.1)
0
NON-COMBUSTIBLE ROOF FLASHING 0
MAINTAINS MINIMUM CLEARANCE
AROUND PIPE(SECTION 10.G)
STORM COLLAR '�
(SECTION 10.H)
VENT PIPE PENETRATES ROOF
PREFERABLY WITHOUT AFFECTING
ROOF RAFTERS(SECTION 8.C)
ATTIC INSULATION SHIELD(NOT
VENT PIPE(SECTIONS 7 and 8) SHOWN)MUST BE USED HERE TO
KEEP INSULATION AWAY FROM
VENT PIPE IF ATTIC IS INSULATED
(SECTION 8.D)
CEILING FIRESTOP
ON FLOOR OF ATTIC
(SECTION 8.C)
FRAMING/HEADER
(SECTION 5.6) FRAMING HEADED OFF
IN CEILING JOISTS
(SECTION S.C)
� OPTIONAL
WALL SWITCH
MANTELAND
MANTEL LECa
(SECTION S.D)
O SURROUND
O
.O
HEARTH EXTENSION
GAS LINE
(SECTION 11)
Figure 4.1 Typical System
20 Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12
B. Design and Installation Considerations D. Inspect Appliance and Components
Heat & Glo direct vent gas appliances are designed to • Carefully remove the appliance and components from
operate with all combustion air siphoned from outside of the packaging.
the building and all exhaust gases expelled to the outside. . The vent system components and decorative doors and
No additional outside air source is required. fronts may be shipped in separate packages.
Installation MUST comply with local, regional, state and • If packaged separately, the log set and appliance grate
national codes and regulations. Consult insurance carrier, must be installed.
local building inspector, fire officials or authorities having
jurisdiction over restrictions, installation inspection and • Report to your dealer any parts damaged in shipment,
permits. particularly the condition of the glass.
Before installing, determine the following: • Read all of the instructions before starting the instal-
lation.Follow these instructions carefully during the
• Where the appliance is to be installed. installation to ensure maximum safety and benefit.
• The vent system configuration to be used. WqRNING! Risk of Fire or Explosion! Damaged parts
• Gas supply piping requirements. could impairsafe operation. DO NOT install damaged, in-
• Electrical wiring requirements. complete or substitute components. Keep appliance dry.
• Framing and finishing details.
• Whether optional accessories—devices such as a fan, Hearth&Home Technologies disclaims any responsibility for,
wall switch, or remote control—are desired. and the warranty will be voided by, the following actions:
• Installation and use of any damaged appliance or vent
system component.
Improper installation, adjustment, alteration, service or
maintenance can cause injury or property damage. For • Modification of the appliance or vent system.
assistance or additional information, consult a qualified • Installation other than as instructed by Hearth & Home
service technician, service agency or your dealer. Technologies.
• Improper positioning of the gas logs or the glass door.
C. Tools and Supplies Needed • Installationand/oruseofanycomponentpartnotapproved
by Hearth& Home Technologies.
Before beginning the installation be sure that the following
tools and building supplies are available. Any such action may cause a fire hazard.
Tape measure Framing material
Pliers Non-corrosive leak check solution- �/ARNING!Risk of Fire, Explosion or Electric Shock!
Hammer Phillips screwdriver DO NOT use this appliance if any part has been under
water. Call a qualified service technician to inspect the
Gloves Framing square appliance and to replace any part of the control system
Voltmeter Electric drill and bits (1/4 in.) and/orgas control which has been under water.
Plumb line Safety glasses
Level Reciprocating saw
Manometer Flat blade screwdriver
1/2 - 3/4 in. length, #6 or#8 Self-drilling screws
Caulking material (300°F minimum continuous exposure
rating)
One 1/4 in. female connection (for optional fan).
Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12 21
5 Framing and Clearances
A. Selecting Appliance Location NOTICE: lllustrations reflect typical installations and are
When selecting a location for the appliance it is important to FOR DESIGN PURPOSES ONLY. lllustrations/diagrams
consider the required clearances to walls (see Figure 5.1). are not drawn to sca/e.Actual installation may vary due to
individual design preference.
WARNING! Risk of Fire or Burns! Provide adequate
clearance around air openings and for service access.
Due to high temperatures,the appliance should be locat-
ed out of traffic and away from furniture and draperies.
NOTE:THE REAR STANDOFF MAY NEED
TO BE REMOVED WHEN VENTING AT 45°
�F A
�-G--�I
1l2 IN. O
� \ � p
\ ALCOVE
�
� INSTALLATION E
A B
C ,�
/ � �
\IC TOP VENT
ONE 90°ELBOW
\
/ REAR VENT, REAR VENT �
� HORIZONTAL TERMINATION ONE ELBOW
� TWO ELBOWS REAR VENT
B NO ELBOWS B
p � �B � � D
O � T \ O
O F
�
� D �
� H �
�D �
A B C D E F G H
600o in. 51 42 72 56-5/8 See Section D. 22 17-3/4 8
mm 1295 1067 1829 1438 Mantel Projections 559 451 203
$000 in. 55-7/8 49 79 61-1/2 See Section D. 22 19-3/4 10
mm 1419 1245 2007 1562 Mantel Projections 559 502 254
Figure 5.1 Appliance Locations-6000 Models
22 Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12
B. Constructing the Appliance Chase stops should be caulked with caulk with a minimum of
A chase is a vertical box-like structure built to enclose the 300°F continuous exposure rating to seal gaps. Gas line
gas appliance and/or its vent system. In cooler climates holes and other openings should be caulked with caulk
the vent should be enclosed inside the chase. with a minimum of 300°F continuous exposure rating or
stuffed with unfaced insulation. If the appliance is being
NOTICE: Treatment of ceiling firestops and wall shield installed on a cement surface, a layer of plywood may be
firestops and construction of the chase may vary with the placed underneath to prevent conducting cold up into the
type of building. These instructions are not substitutes room.
for the requirements of local building codes. Therefore, C. Clearances
you MUST check local building codes to determine the
requirements to these steps. NOTICE:Install appliance on hard metal or wood surfaces
extending full width and depth. DO NOT install directly
Chases should be constructed in the manner of all out- on carpeting, vinyl, tile or any combustible material other
side walls of the home to prevent cold air drafting prob- than wood.
lems. The chase should not break the outside building
envelope in any manner. WARNING! Risk of Fire! Maintain specified air space
clearances to appliance and vent pipe:
Walls, ceiling, base plate and cantilever floor of the chase
should be insulated. Vapor and air infiltration barriers • Insulation and other materials must be secured to prevent
should be installed in the chase as per regional codes for accidental contact.
the rest of the home. Additionally, in regions where cold • The chase must be properly blocked to prevent blown
air infiltration may be an issue,the inside surfaces may be insulation or other combustibles from entering and
sheetrocked and taped for maximum air tightness. making contact with fireplace or chimney.
To further prevent drafts, the wall shield and ceiling fire- • Failure to maintain airspace may cause overheating and
a fire.
�� I
A
�_ E
_ y
� .._ � ------
D. Mantel and Wall Projections Combustible Mantel Legs or Wall Projections
W�IRN/NG! Risk of Fire! Comply with all minimum clear-
ances as specified. Framing or finishing material closer than
the minimums listed must be constructed entirely of noncom-
bustible materials(i.e., steel studs, concrete board, EtC�. INTERIOR WALL
Combustible Mantels TOP VIEW
TO CEILING
��
�8 A B
,2 >'
11 �
10 32 FIREPLACE OPENING
9 �l
8 25 /
� �g MANTEL LEG OR WALL PROJECTIONS
6 18
5 17
q �s If A minimum is_,then B maximum is
3 — 15 A m�nes 2-7/16 3-7/16 4-7/16 5-7/16 6-7/16 7-7/16
14 Millimeters 62 87 113 138 164 189
13 p Inches 1 2 3 4 5 ao
12 O Millimeters 25 51 76 102 127 00
2-1/2 1.�
� 10 Figure 5.4 Clearances to Mantel Legs or Wall Projections
5 (Acceptable on both sides of opening.)
� MEASUREMENTSFROM
TOP EDGE OF THE OPENING
Note:All measurements in inches.
Note: Measurement is taken from top of the
opening, NOT the top of the fireplace.
Figure 5.3 Minimum Vertical and Maximum Horizontal
Dimensions of Combustibles
24 Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12
sTermination Locations
A. Vent Termination Minimum Clearances
A B
6 in.(minimum)up to 20 in. 18 in.minimum
A WA R N I N G 152 mm/508 mm 457 mm
20 in.and over 0 in.minimum
Fire Risk.
Gas, Wood or Fuel Oil
Maintain vent clearance to combustibles as Termination Cap
specified. �
• DO NOT pack air space with insulation or other I
materials. �
Failure to keep insulation or other materials away B
from vent pipe may cause overheating and fire. }
I A�
HORIZONTAL G2S
OVERHANG
_ Termination ����
Cap,� �0��
2 FT. 20 WCHES MIN. VERTICAL �0��
MIN. WqLL
LOWEST ����
DISCHARGE ����
OPENING
GAS DIRECT VENT ����
TERMINATION CAP ����
X
12 * If using decorative cap cover(s),this distance may need to be
increased.Refer to the installation instructions supplied with the
ROOF PITCH decorative cap cover.
IS X/12
.. In a staggered installation with both gas and wood or fuel oil
H(MIN.)-MINIMUM HEIGHT FROM ROOF terminations,the wood or fuel oil termination cap must be
TO LOWEST DISCHARGE OPENING
higher than the gas termination cap.
Figure 6.2 Staggered Termination Caps
Roof Pitch H(Min.)Ft.
Flat to 6/12...........................................................1.0�
Over 6/12 to 7/12.................................................1.25"
Over 7/12 to 8/12.................................................1.5�
Over 8/12 to 9/12.................................................2.0'
Over 9/12 to 10/12...............................................2.5
Over 10/12 to 11/12.............................................3.25
Over 11/12 to 12/12.............................................4.0
Over 12/12 to 14/12.............................................5.0
Over 14/12 to 16/12.............................................6.0
Over 16/12 to 18/12.............................................7.0
Over 18/12 to 20/12.............................................7.5
Over 20/12 to 21/12.............................................8.0
"3 foot minimum in snow regions
Figure 6.1 Minimum Height From Roof To Lowest Discharge
Opening
Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12 25
/ o �
� hIn1l N �
P u
I� F -- R
\ I I
0\ Q
\
�� B
� �Hori � �
�,y � � a• ��. � '\ V
-G H
V�p M V `1,H,P O 1 L
� A
V K Electrical K V
� =VENT TERMINAL se'""e
X =AIR SUPPLY INLET �
� =AREA WHERE TERMINAL IS NOT PERMITTED �
A = 12 inches.................clearances above grade, veranda, Covered Alcove AppliCations
porCh, deCk or balCOny (Spaces open only on one side and with an overhang)
B = 12 inches.................clearance to window or door that may N = 6 inches ........... non-vinyl sidewalls
be opened,or to permanently closed 12 inches .........vinyl sidewalls
window
C = 18 inches.................clearance below unventilated soffit O = 18 inches ......... non-vinyl soffit and overhang
18 inches.................clearance below ventilated soffit 42 inches .........vinyl soffit and overhang
30 inches................clearance below vinyl soffits and P = 8 ft.
electrical service
QMIN RMAX
D = 9 inches...................clearance to outside corner 1 cap 3 feet 2 X Q ACTUAL
E = 6 inches...................clearance to inside corner 2 caps 6 feet � X Q ACTUAL
F = 3 ft. (Canada)..........not to be installed above a gas me-
ter/regulator assembly within 3 feet 3 caps 9 feet Z�3 X Q qCTUAL
horizontally from the center-line of the 4 caps 12 feet ��2 X Q ACTUAL
regulator
QM,,,_#termination caps x 3 RMqx=(2/#termination caps)x Qqcrua�
G = 3 ft...........................clearance to gas service regulator
vent outlet
H = 9 inches(U.S.A) Measure vertical clearances from this surtace.
12 inches(Canada).clearancetonon-mechanical(unpow-
ered)air supply inlet,combustion air
inlet or direct-vent termination
i = 3 ft. (U.S.A.)
6 ft. (Canada)...........clearance to a mechanical(powered) ' �� �����
air supply inlet , ' •�flm� ���
All mechanical air intakes within 10 feet of a termination cap NpT U�11 �D
must be a minimum of 3 feet below termination. ° �• ��• fl(I����
J = 7 ft.......................... On ublic property: clearance above ��
paved sidewalk or a paved driveway.
A vent shall not terminate directly above a sidewalk or paved
driveway which is located between two single family dwellings Measure horizontal clearances from this surface.
and serves both dwellings.
CAUTION! Risk of Burns! Termination caps are HOT,
K = 6 inches.................clearance from sides of electrical consider proximity to doors, traffic areas or where people
service may pass or gather(sidewalk, deck,patio, etc.). Listed cap
L = 12 inches................clearance above electrical service shields available. Contact your dealer.
Location of the vent termination must not interfere with access to the • LoCal Codes or regulations may require different
electrical service. Cleal"allCes.
• Vent system termination is NOT permitted in screened
porches.
M = 18 inches....................clearanceunderveranda,porch,deck, • Vent system termination is permitted in porch areas with
balcony or overhang two or more sides open.
42 inches ................vinyl or composite overhang • Hearth & Home Technologies assumes no responsibility
Permitted when veranda, porch, deck or balcony is fully open for the im ro er erformance of the a liance when the
on a minimum of 2 sides beneath the floor. P P P PP
venting system does not meet these requirements.
Figure 6.3 Minimum Clearances for Termination • Vinyl protection kits are suggested for use with vinyl siding.
26 Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12
7 Vent Information and Diagrams
A. Approved Pipe ,
This appliance is approved for use with Hearth & Home ,
Technologies DVP or SLP venting systems. Refer to Sec- '�
tion 16B for vent component information. ,����
DO NOT mix pipe, fittings or joining methods from differ- I
ent manufacturers. Vertical ,��I = �
The pipe is tested to be run inside an enclosed wall. ,;;,�. ',�
There is no requirement for inspection openings at each ,�,�`L ;�
joint within the wall. ,�' ;
WARNING! Risk of Fire or Asphyxiation. This appli- 8-1/2 in.
ance requires a separate vent. DO NOT vent to a pipe
serving a separate solid fuel burning appliance. ,
B. Vent Table Key �Horizontal—>
The abbreviations listed in this vent table key are used in
the vent diagrams.
Figure 7.1
Symbol Description
V� First section(closest to appliance)of vertical length �. Measuring Standards
Vertical and horizontal measurements listed in the vent
Vz Second section of vertical length diagrams were made using the following standards.
H, First section(closest to appliance)of horizontal length • Pipe measurements are shown using the effective length
of pipe (see Figure 7.2).
Hz Subsequent sections of horizontal length
• Horizontal terminations are measured to the outside
mounting surFace(flange of termination cap)(see Figure
C. Use of Elbows 6.3).
Diagonal runs have both vertical and horizontal vent as- • Vertical terminations are measured to bottom of
pects when calculating the effects. Use the rise for the termination cap.
vertical aspect and the run for the horizontal aspect (see • Horizontal pipe installed level with no rise.
Figure 7.1).
Two 45° elbows may be used in place of one 90° elbow.
On 45°runs, one foot of diagonal is equal to 8-1/2 in. (216
mm) horizontal run and 8-1/2 in. (216 mm) vertical run.A Effective Length
length of straight pipe is allowed between two 45°elbows P�pe Inches Millimeters
(see Figure 7.1). �vPa a �oz
Effective DVP6 6 152
Height/Length DVP12 12 305
DVP24 24 610
DVP36 36 914
DVP48 48 1219
OVP6A 3 to 6 76 to 152
DVP12A 3 to 12 76 to 305
Figure 7.2 DVP Pipe Effective Length
Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12 27
E. Vent Diagrams
Top Vent - Horizontal Termination
A WARNING
Note:The 6000/8000 series fireplaces can adapt to SLP series Fire Risk. Explosion Risk.
vent pipe, if desired. Do NOT pack insulation or other combustibles
When venting off the top of the unit, use a DVP-2SL adapter and a between ceiling firestops.
minimum 48 inch vertical section of SLP series vent pipe. • ALWAYS maintain specified clearances around
A DVP-SLP24 adapter may also be used with a 24 inch vertical venting and firestop systems.
section of SLP series vent pipe. • Install wall shield and ceiling firestops as speci-
After the 48 inch vertical section, the venting table rules must be fied.
followed.The first 48 inch vertical section is NOT counted as part Failure to keep insulation or other material away
of the vertical components in the table. It is still counted as part of from vent pipe may cause fire.
the overall maximum run. All venting table rules for the vent run
must still be followed.
A WARNING
Example: DVP pipe 3 ft. min. vertical = 11 ft. max. horizontal Fire Risk.
SLP pipe 7 ft. min.vertical = 11 ft. max. horizontal • When using DVP-HRC-SS and DVP-HRC-ZC-
SS termination caps on top vented fireplaces,a
6 inch minimum vertical vent section is required
Top Vent - Horizontal Termination before installing first elbow.
One Elbow
6000C-IPI 8000GIPI
V� Minimum H� Maximum V� Minimum H� Maximum
Elbow only 2 ft 610 mm Elbow Only 2 ft. 610 mm
6 in. 152 mm 4 ft. 1.2 m 1 ft. 305 mm 3 ft. 914 mm
1 ft. 305 mm 6 ft. 1.8 m 2 ft. 610 mm 6 ft. 1.8 m
1-1/2 ft. 457 mm 10 ft. 3.0 m 3 ft. 914 mm 11 ft. 3.4 m
2 ft. 610 m 15 ft. 4.6 m 4 ft. 1.2 m 20 ft. 6.1 m
2-1/2 ft. 762 mm 20 ft. 6.1 m V� + H� =40 ft. (12.2 m)Maximum
3 ft. 914 mm 25 ft. 7.6 m H� =20 ft. (6.1 m) Maximum
V, + H, =40 ft. (12.2 m) Maximum
H� =25 ft. (7.6 m)Maximum
Note: For corner installations:A 6 inch (152
mm) section of straight pipe may need to
be attached to the appliance before a 90°
elbow, to allow the vent pipe to clear the top
standoffs.
\
V�
H�
� � .�
.�
0
Figure 7.3
(�b ,. .,
28 Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12
Top Vent - Horizontal Termination - (continued)
Two Elbows 6000C-IPI $000c-iPi
V� Minimum H, + HZ Maximum V� Minimum H� + HZ Maximum
Elbow only Not allowed Elbow only Not allowed
6 in. 152 mm 2 ft. 610 mm 6 in. 152 mm Not allowed
1 ft. 305 mm 4 ft. 1.2 m 1 ft. 305 mm 2 ft. 610 mm
1-1/2 ft. 457 mm 11 ft. 3.4 m 2 ft. 610 mm 4 ft. 1.2 m
2 ft. 610 mm 19 ft. 3.8 m 3 ft. 914 mm 6 ft. 1.8 m
2-1/2 ft. 762 mm 22 ft. 6.7 m 4 ft. 1.2 m 8 ft. 2.4 m
V� + H�+ HZ=40 ft. (12.2 m) Maximum 6 ft. 1.8 m 12 ft. 3.6 m
H�+ HZ=22 ft. (6.7 m)Maximum 10 ft. 3.0 20 ft. 6.1 m
V� = 1 ft. (305 mm)Minimum
V� + H�+ HZ=40 ft. (12.2 m) Maximum
H�+ HZ=20 ft. (6.0 m) Maximum
V� = 1 ft. (305 mm) Minimum
� Note: For corner installations:A 6 inch
� V (152 mm)section of straight pipe may
' need to be attached to the appliance
HZ H� before a 90° elbow, to allow the vent
� � pipe to clear the top standoffs.
INSTALLED
HORIZONTALLY
O � '
Figure 7.4 I �..a _ _
Three Elbows v, Min. H� Max. VZ Min. Hz Max.
Elbow only 2 ft. 610 mm 0 in. 0 mm 1 ft. 305 mm
6 in. 152 mm 3 ft 914 mm 6 in. 152 mm 2 ft. 610 mm
1 ft. 305 mm 6 ft. 1.8 m 1 ft. 305 mm 6 ft. 1.8 m
2 ft. 610 mm 11 ft.* 3.4 m" 2 ft. 610 mm 10 ft.* 3.1 m*
3ft. 914mm 16ft� 4.9m" 3ft. 914mm 14ft.� 4.3m�
� � �H� + HZ=20 ft. (6.1 m)Maximum V� +VZ+ H� + HZ=40 ft. (12.2 m) Maximum
�� �
HZ
V
��.g0 f 2 �
�
�
� �
� • �H� V�
� �1
0
Figure 7.5 � o 0
Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12 29
Top Vent - Vertical Termination Flue Restrictor Instructions
NO ElbOw 1. Remove exhaust shield using a 1/4 inch nut driver by
removing the four screws securing it in place(see Figure
7.7).
V� = 40 ft. Max. (12.4 m)
V� = 3 ft. Min. (914 mm)
�� �
Note: If installing a vertical vent/
termination off the top of the ap-
pliance, the flue restrictor should J� �
be used. � �
EXHAUST �
SHIELD
�.• .
� �' .
. v
FLUE
RESTRICTOR
� � B
I��
'I �j
/.�
�
Figure 7.7
2. Break the flue restrictor into two pieces. Do this by
�/ bending the part back and forth until it breaks (see
�
Figure 7.8).
0 0 0 0 0 0
BREAK
� HERE
.� � �
0 0 0 0 0 0
OFigure 7.8 Flue Restrictor
Figure 7.6
30 Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12
Top Vent - Vertical Termination (continued) 4. Center the Flue Restrictor on vent and secure in place
by using two self-tapping screws (see Figure 7.10).
3. Match the amount of vertical you have in the system 5. Reinstall the Exhaust Shield.
with the chart to find the appropriate position to set the
Flue Restrictor(see Figure 7.9).
Vertical TOP VENT REAR VENT o 0 o O o
NG LP NG LP 1 2 3 4 5
4 ft. 1-1 No No No
Restrictor Restrictor Restrictor
8 ft. 2-2 1-2 1-1 No
Restrictor
15 ft. 3-3 3-2 2-2 1-2 SETTING
20 ft. 3-4 3-3 3-3 2-3
25 ft. 3-4 3-3 3-3 2-3
1 2 3 4 5
30 ft. 4-4 3-4 3-4 3-3 0 0 0 0 0
Figure 7.10
35 ft. 4-4 3-4 3-4 3-3
40 ft. 4-4 4-4 4-4 3-4
Figure 7.9
Note: If the DVP-2SL or DVP-SLP24 adapter is used with
SLP pipe, you MUST subtract one number from the table
above.
Example: Top vent 40 ft vertical with DVP pipe = 4-4
Top vent 40 ft vertical with SLP pipe = 3-3
Two Elbows V� H� Maximum VZ V� +VZ Min.
� Elbow only 2 ft. 610 mm * " *
6 in. 152 mm 6 ft. 1.8 m * � *
2 ft. 610 mm 11 ft. 3.4 m * � `
m m 3 ft. 914 mm 16 ft. 4.9 m * "` �
4 ft. 1.2 m 20 ft. 6.1 m � "` *
V� +VZ+ H� = 50 ft. (15.2 m)Maximum
�� *No specific restrictions on this value EXCEPT
V� +VZ+ H� cannot exceed 50 ft(15.2 m)
/
�
� V,
H� �
�
0
.� O �
Figure 7.11
�
Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12 31
Top Vent - Vertical Termination - (continued)
V� H� +HZ VZ V� +VZ Minimum H� +HZ Maximum
Three Elbows
Elbow only 1 ft. 305 mm � * * 1 ft. 305 mm
6 in. 152 mm 2 ft. 610 mm � � * 2 ft. 610 mm
1 ft. 305 mm 2 ft. 610 mm � � � 2 ft. 610 mm
2ft. 610mm 4ft. 1.2m � � � 4ft. 12m
3 ft. 914 mm 9 ft. 2.7 m � � � 9 ft. 2.7 m
� 4 ft. 1.2 m 18 ft. 5.5 m � � � 18 ft. 5.5 m
H� + HZ=20 ft. (6.1 m)Maximum V� +VZ+ H� + HZ=40 ft. (12.2 m)Maximum
0 0
VZ
H��
�
�H
2� V
1
INSTALLED
HORIZONTALLY
�
Figure 7.12 ,� � � •
32 Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12
Rear Vent - Horizontal Termination
No Elbow H� = 16 in. (406 mm) Maximum
o �
� o 0
�
0
H� o , om
���� �
.�� .�
Figure 7.13
One 45° Elbow
Do not use a 45°elbow in corner installations.
Use two 90°elbows instead. �H1
.
e
Figure 7.14
Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12 33
Rear Vent - Horizontal Termination - (continued)
H� Maximum V� Minimum HZ H� + HZ Maximum
Two Elbows
1 ft. 305 mm Back to Back 1 ft. 305 mm 2 ft. 610 mm
90° Elbows
2 ft. 610 mm 6 in. 152 mm 2 ft. 610 mm 4 ft. 1.2 m
3 ft. 914 mm 1 ft. 305 mm 2 ft. 610 mm 5 ft. 1.5 m
3 ft. 914 mm 2 ft. 610 mm 4 ft. 1.2 m 7 ft. 2.1 m
3ft. 914mm 3ft. 914mm 9ft. 2.7m 12ft. 3.7m
3 ft. 914 mm 4 ft 1.2 m 17 ft. 5.2 m 20 ft.' 6.1 m�
V� + H� + HZ=40 ft. (12.2 m) Maximum H� = 3 ft. (914 mm)Maximum
�H� + HZ=20 ft(6.1 m) Maximum
�
HZ V� o �.
� o 0
�`�.�
H o
�
1
Q Om
Figure 7.15
H� Maximum V� Minimum HZ+H3 H�+ Hz+ H3 Max.
Three Elbows
1 ft. 305 mm Back to Back 1 ft. 305 mm 2 ft. 610 mm
90° Elbows
2 ft. 610 mm 6 in. 152 mm 1.5 ft. 457 mm 3.5 ft. 1.1 m
3 ft. 914 mm 1 ft. 305 mm 2 ft. 610 mm 5 ft. 1.5 m
3 ft. 914 mm 2 ft. 610 mm 4 ft. 1.2 m 7 ft. 2.1 m
INSTALLED 3 ft. 914 mm 3 ft. 914 mm 9 ft. 2.7 m 12 ft. 3.7 m
HORIZONTALLY 3 ft. 914 mm 4 ft. 1.2 m 12 ft. 3.7 m 15 ft. 4.6 m
V�+ H�+ H2+ H3=40 ft. (12.2 m)Maximum H�= 3 ft. (914 mm)Maximum
H�+ HZ+ H3=20 ft. (6.1 m)Maximum
H � �H
� 3 2\
�� y
T � �
�, � o 0
�
0
0
H o , om
,
Figure 7.16
34 Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12
Rear Vent - Vertical Termination
One Elbow O V� Minimum H� Maximum
O 6 in. 152 mm 2 ft. 610 mm
1 ft. 305 mm 3 ft. 914 mm
2 ft. 610 mm 5 ft. 1.5 m
3 ft. 914 mm 7 ft. 2.1 m
/ o 0 4 ft. 1.2 m 8 ft. 2.4 m
5 ft. 1.5 m 8 ft. 2.4 m
V� + H� =40 ft. (12.2 m) Maximum
H� =8 ft. (2.4 m) Maximum
V� O � "
� � O �
H�
� �
0
� . Om
Figure 7.17
Two Elbows V� Minimum H� + HZ Maximum
O Back to Back 90°Elbows 3 ft. 914 mm
2ft. 610mm 6ft. 1.8m
4ft. 1.2m 9ft. 2.7m
6 ft. 1.8 m 12 ft. 3.7 m
� m 8 ft. 2.4 m 15 ft. 4.6 m
V� + H� =40 ft. (122 m) Maximum
H� + HZ=8 ft. (2.4 m) Maximum
V�
0 � .
INSTALLED � � O O
HORIZONTALLY H
� �
� �
�H �
z�
� . Om
Figure 7.18
Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12 35
Rear Vent - Vertical Termination - (continued)
Three Elbows O H� Maximum V� Minimum HZ H� +HZ Maximum
2 ft. 610 mm 6 in. 152 mm 2 ft. 610 4 ft. 1.2 m
mm
� 0 3 ft. 914 mm 1 ft. 305 mm 4 ft. 1.2 m 7 ft. 2.1 m
5 ft. 1.5 m 2 ft. 610 mm 6 ft. 1.8 m 11 ft. 3.4 m
�/ 7 ft. 2.1 m 3 ft. 914 mm 8 ft. 2.4 m 15 ft. 4.6 m
z
8ft 2.4m 4ft. 1.2m 10ft. 3.1 m 18ft. 5.5m
H�=8 ft(2.4 m) Max. V� +VZ+ H� + HZ=40 ft(12.2 m)Max.
H� + HZ=20 ft(6.1 m) Max.
\
HZ�/
1 0 �.
V� �I o 0
/
0
0
Figure 7.19 0 _ om
�
-�H,
Three Elbows H� HZ H3 V� Minimum H� + HZ+ H3 Maximum
� * * * 8 ft. 2.4 m 6 ft. 1.8 m
* * * 9 ft. 2.7 m 7 ft. 2.1 m
. .
* * * 10 ft. 3.1 m 8 ft. 2.4 m
* * * 10 ft. 3.1 m 8 ft. 2.4 m
V V� + H� + HZ+ H3=40 ft. (12.2 m)Maximum
� 'No specific restrictions on this value EXCEPT
V� + H� + HZ+ H3 cannot exceed 40 ft. (12.2 m)Maximum
H� + Hz+ H3=8 ft. (2.4 m)Maximum
H3�
�
o �
� � ° o
�H,
� o �
H2 � � .
0 om
INSTALLED
Figure 7.20 HORIZONTALLY
36 Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12
Coaxial to Colinear Venting OUTSIDE FACE OF
The coaxial to colinear adapter (DV-46DVA-GCL) is ap- FiREP�ACE�
proved for installations into solid fuel masonry or factory
built fireplaces that have been installed in accordance EXHAUST VENT PIPE
with the National, Provincial, State and local building
codes. The DV-46DVA-GCL must be recessed into exist-
ing masonry fireplace. See Table 1 and Figure 7.21. ToP oF FiReP�ace
OPENING
5 IN.MIN.
INLET AIR VENT PIPE EXHAUST VENT PIPE 3 1N.MIN.�
SHADED AREA DEFINED AS
"INSIDE EXISTING MASONRY
FIREPLACE"
Figure 7.22.Existing Fireplace DV-46-CGL-CGL
Clearance Requirements
Figure 7.21. Coazial/ColinearAppliance Connector
Clearances to Combustibles:
WARNING! Risk of Fire! Coaxial to colinear venting
configuration may only be used in existing non-combus- Refer to Section 5 for clearances to the appliance, man-
tible chimney. Installation in any other venting application tel, mantel legs and wall projection.
could cause fire. Refer to Section 8 for pipe clearances to combustibles.
Prior to installing the gas appliance: Termination Cap
• Have the chimney and adjacent structure inspected For installation of termination cap see minimum vent
and cleaned by qualified professionals. Hearth & Home heights for various pitched roofs. See Section 6 of appli-
Technologies recommends that NFI or CSIA certified ance owner's manual.
professionals,or technicians under the direction of certi- Flue Damper
fied professionals, conduct a minimum of a NFPA 211
Level 2 inspection of the chimney. Fully lock the solid fuel fireplace's flue damper in the open
• Replace component parts of the chimney and fireplace Position, OR completely remove it.
as specified by the professionals. Venting Components
• Ensure all joints are properly engaged and the chimney The LINK-DV30B is approved for use with the coaxial/co-
is properly secured. linear venting application. The LINK-DV30B kit includes:
• Two 30 feet sections of flexible vent pipe (3 inches Q1).
Table 1 One section is used to draw combustion air and the other
CLEARANCE TO COMBUSTIBLES REQUIREMENTS section is used to expel exhaust gases.
DV-46DVA-GCL 3 IN. • One vertical termination cap.
Exhaust vent Pipe 5 IN. CAUTION!DO NOT use any flue restrictor when vent-
ing with the DV-46DV.4-GCL adapter and LINK-DV30B
kit. This may result in poor flame appearance, sooting,
pilot malfunction, or overheating.
Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12 37
Connecting the DV-46DVA-GCL Adapter to Appliance three screws.
Top Vent • Attach one section of flexible vent pipe to the stainless
• Remove top seal cap and insulation if equipped. See steel flex pipe with three self-tapping screws.
Section 14, "Appliance Setup."Attach the DVP-2SL to • Attach one section of flexible vent pipe to the inlet collar
the 8 inch starting collar. Follow installation instructions on top of the DV-46DVA-GCL adapter with three self-
included with DVP-2SL kit. Attach the DV-46DVA-GCL tapping screws.
adapter to the appliance starting collar with 3-1/2 in. • To minimize cold air drafts, seal around the flex vents
self-tapping screws. See Figure 7.23. at the damper inside the chimney with non-combustible
Rear Vent unfaced fiberglass or rock wool insulation.
• Remove the rear seal cap and insulation if equipped. The DV-46DVA-GCL adapter must be recessed into existing
Connect the DVP-2SL adapter to the vertically positioned masonry fireplace. This measurement is taken from the top
elbow. Follow installation instructions included with DVP- of the fireplace opening. See Table 1 and Figure 7.22.
2SL kit.Secure DV-46DVA-GCL adapter to DVP-2SL with
3-1/2 in. self-tapping screws. See Figure 7.23. WARN/NG! Risk of Fire, Explosion or Asphyxiation!
Connecting the LINK-DV30B to the DV-46DVA-GCL Do NOT connect this gas appliance to a chimney flue
adapter serving a separate solid fuel or gas burning appliance.
• Insert the two sections of flexible vent pipe down the • May impair safe operation of this appliance or other
existing chimney. appliances connected to the flue.
• Vent this appliance directly outside.
• Attach one section of stainless steel flex pipe to the
exhaust collar on top of the DV-46DVA-GCL adapter with • Use separate vent system for this appliance.
REAR VENT TOP VENT
�TERMINATION CAP
� TERMINATION CAP
_ CAUTION! DO NOT use any flue restric-
tor when venting with the DV-46DVQ-GCL
adapter and LINK-DV306 kit. This may re-
sult in poor flame appearance, sooting, pilot
S� malfunction, oroverheating. ��,,
� \��
NOTICE: To achieve optimum perfor- �,
� � mance of appliance, minimize or avoid �� �
i
I�ends in exhaust vent pipe.
EXISTING CHIMNEY\ EXISTING CHIMNEY
EXHAUST AIR EXHAUST AIR
VENT PIPE INLET AIR VENT PIPE VENT PIPE INLET AIR
/ /VENT PIPE
i
The first 3 feet of � The first 3 feet of
exhaust flue must be t exhaust flue must
EXISTING CHIMNEY_ stainless flex pipe. be stainless flex
I EXISTING CHIMNEY_,, �
COAXIAL/COLINEAR �� P�Pe�
APPLIANCE CONNECTOR To minimize cold air I
COAXIALICOLINEAR
drafts,seal with %� To minimize cold air
DVP-2SL / APPLIANCE CONNECTOR
non-combustible � /I drafts,seal with
DIRECT VENT FIREPLACE -- insulation. DVP-2SL\ / �� non-combustible
\ � insulation.
\ o DIRECT VENT FIREPLACE
0
HEARTH � O
FLOOR �� Bo• HEARTH O
FLOOR
� �H- + —��' � °I B�' —
V H
V
Minimum 10 ft. 3.05 m 0 ft. 0 mm
Minimum 10 ft. 3.05 m
Maximum 40 ft. 12.2 m 2 ft. 610 mm
Maximum 40 ft. 12.2 m
Figure 7.23
38 Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12
8 Vent Clearances and Framing
A. Pipe Clearances to Combustibles B. Wall Penetration Framing
WARNING!Risk of Fire!Maintain air space clearance to Combustible Wall Penetration
vent. DO NOT pack insulation or other combustibles: Whenever a combustible wall is penetrated, you must
• Between ceiling firestops frame a hole for the wall shield firestop(s).The wall shield
• Between wall shield firestops firestop maintains minimum clearances and prevents cold
• Around vent system air infiltration.
Failure to keep insulation or other material away from • The opening must be framed on all four sides using the
vent pipe may cause over heating and fire. same size framing materials as those used in the wall
construction.
• SLP pipe-Awall shield firestop must be placed on each
Note:Heat shields MUST overlap by a minimum of 1-1/2 in.(38 mm). SIC�I@ Of all interior wall. A minimum 1-1/2 in. (38 mm)
•DVP heat shield-designed to be used on a wall 4 in.to 7-1/4 in.(102 mm to 184
mm�cn;�k. overlap of attached heat shields must be maintained.
•If wall thickness is less than 4 in.the existing heat shields must be field trimmed.If
wall thickness is greater than 7-1/4 in.a DVP-HSM-B will be required. ' DVP pipe-A wall shield firestop is required on one side
•SLP heat shield-designed to be used on a wall 43/8 in.to 7-5/8 in.(111 mm to only on interior walls. If your local inspector requires a
194 mm thick).
•If wall thickness is less than 4-3/8 the existing heat shields must be field trimmed. WBII Slll@IC� flr@StOp 011 I�OtII SIC�I@S, then both wall shield
If wall thickness is greater than 7-5/8 in.a DVP-HSM-B will be required. flr2StOpS IIIUSt r1aV@ a r12at Srl l@�C��I"2f2f t0 S2Ct1011 �6.B.�
attached to them.
(DVP-SLP Pipe Shown) • See Section 10.M. for information for regarding the in-
�� stallation of a horizontal termination cap.
Heat 3 in.(76 mm) Non-Combustible Wall Penetration
3 in.(76 mm) Shield top clearance'
`°P°'ea`a"°e y � �"eat If the hole bein enetrated is surrounded b noncom-
_. Shield 9 p Y
T T �0�0� bustible materials such as concrete, a hole with diameter
1 in.(25 mm) + y ���� one inch reater than the i e is acce table.
dearance around 9 p p p
vertical sections 'L _
�- ---�1 in.(25 mm) Whenever a non-combustible wall is penetrated, the wall
wa„ clearance shield firestop is only required on one side and no heat
� � Shield bottom&sides
Firestop shield is necessary.
WALL
�
Heat 3 in.(76 mm) �
Shield� �top dearance* �
. , l �Sh e�ld � �
'+ ��0���� —q �
� i !�B.0��0. :� o �
� �1 in.(25 mm) 10 in. 12 in. � ��A O
Wall clearance
Shield bottom&sides C
Firestop D
a e o 0 , 00
WALL 10 in. 12 in. �
�When using SLP or SL-D pipe,minimum clearances from the vent pipe to combus-
tible materials at inside wall firestops are: Top:2-1/2 in.(64 mm)
Bottom:1/2 in.(13 mm) A� B*
Sides:1 in.(25 mm) �
Figure 8.1 Horizontal Venting Clearances To Combustible /
Materials
A* B* C D
in. 42-3/4 27-7/8 41-3/4 26-7/8
6000 mm 1086 708 1060 683
in. 44-3/4 29-7/8 44-1/8 28-7/8
8000
mm 1137 759 1111 733
" Shows center of vent framing hole for top or rear venting.The center of the
hole is one(1)in.(25.4 mm)above the center of the horizontal vent pipe.
Figure 8.2 Wall Penetration
Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12 39
C. Install the Ceiling Firestop
A ceiling firestop MUST be used between
floors and attics.
• DVP pipe only - Frame an opening 10 in.
by 10 in. (254 mm by 254 mm) whenever i
the vent penetrates a ceiling/floor (see
Figure 8.3). i ATTIC ABOVE
• SLP pipe only - Frame opening 9 in. x 9 i
in. (229 mm x 229 mm) whenever the vent i � i
� �
penetrates a ceiling/floor(see Figure 8.3). i i i i �
• Frame the area with the same sized lumber � � q
as used in ceiling/floorjoist. , �
• The ceiling firestop may be installed above or i �
below the ceiling joists when installed with a
attic insulation shield. It must be underjoists � – �
between floors that are not insulated. Refer �,—�
to Figure 8.4.
• Secure with three fasteners on each side. � �/
A
WARNING!Risk of Fire!DO NOT pack insu- /�
lation around the vent. Insulation must be kept
back from the pipe to prevent overheating. �
� PIPE A
� DVP 10 in.(254 mm)
SLP 9 in.(229 mm)
�
0
0
0
Figure 8.3 Installing Ceiling Firestop
INSTALL ATTIC INSULATION SHIELDS
BEFORE OR AFTER INSTALLATION OF VENT SYSTEM
3 FASTENERS
PER SIDE T T
1
1 � 1 �
CEILING FIRESTOP CEILING FIRESTOP
INSTALLED BELOW CEILING INSTALLED ABOVE CEILING
Figure 8.4 Installing the Attic Shield
40 Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12
D. Install Attic Insulation Shield
BEND ALL TABS INWARD 90°
WARNING! Fire Risk. DO NOT allow loose materials or TO MAINTAIN CLEARANCE
insulation to touch vent. Hearth & Home Technologies AND PREVENT INSULATION
Inc. requires the use of an attic shield. FROM FALLING INSIDE
The National Fuel Gas Code ANSI Z223.1 and NFPA 54
requires an attic shield constructed of 26 gauge minimum
metal that extends at least 2 in. (51 mm)above insulation.
BEND 3 TABS
Attic shields must meet specified clearance and be se- ou'rwAR� 'ro
CUI'@d Ill p18C0. FASTEN TO CEILING
Flat Ceilin Installation FIRESTOP-BEND
g REMAINING TABS
• R@f710Ve One Shleld fCOI71 bOX. INWARD 90 DEGREES
TO MAINTAIN
NOTICE: Cut previously installed batt insulation to make INSERT 3 CLEARANCE
room for the attic insulation shield. scRews
• Wrap shield around pipe if pipe is already installed in
area to be insulated.
• Match the three holes in each side and fasten with three
screws to form a tube.
• Bend three tabs on the bottom of the shield outward to
allow attachment to the ceiling firestop.
Figure 8.5 Attic Insulation Shield
• Bend the remaining bottom tabs inward 90°to maintain
the air space between the pipe and the shield. Set the
shield on the ceiling firestop and attach to the firestop. E. Installing the Optional Heat-Zone°Gas Klt
• Bend all tabs inward 90° around the top of the shield. • Remove the knockout from the fireplace and discard it
These tabs must be used to prevent blown insulation (see Figure 8.6).
from getting between the shield and vent pipe, and to . Center the duct collar around the exposed hole and
maintain air space clearance. attach it to the fireplace with 3 screws. Note: Do this
BEFORE final positioning of fireplace.
• Determine the location for the air register/fan housing
assembly.
Vaulted Ceiling Installation Reference the Heat-ZoneO Gas kit instructions for the
• Remove one shield from box. remaining installation steps.
NOTICE: Cut previously installed batt insulation to make
room for the attic insulation shield.
/
• Cut the attic insulation shield (if application is for vaulted /,
ceiling)to fit your ceiling pitch. Snip cut edge to recreate //
1 in. bend tabs all the way around the bottom. ' 0�
• Wrap shield around pipe if pipe is already installed in 0�
area to be insulated. ��
�� o
• Match the three holes in each side and fasten with three . °
screws to form a tube. O 0 �i�
• Bend three tabs on the bottom of the shield outward to HEAT-ZONE�'GAS � o
ATTACHES HERE
allow attachment to the ceiling firestop. --- -
• Bend the remaining bottom tabs inward 90°to maintain
the air space between the pipe and the shield. Set the �
shield on the ceiling firestop and attach to the firestop. ' � I
• Bend all tabs inward 90° around the top of the shield. � � `''• 0
These tabs must be used to prevent blown insulation
from getting between the shield and vent pipe, and to Figure 8.6 Heat-Zone°Cover Plate
maintain air space clearance.
Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12 41
9 Appliance Preparation
A. Top Vent NOTICE:Once the seal cap has been removed it CANNOT
CAUTION! Risk of Cuts, Abrasions or Flying Debris.
be reattached.
Wear protective gloves and safety g/asses during instal-
lation. Sheet metal edges are sharp. -
NOTICE: Once appliance is set up for top or rear venting, �
it CANNOT be changed at a later time. . ,�.� - �
,
� ,_ � ��
.*� � � � .
� � a ��
� �,_.
Ja.
.. .�Y�' �� ��'-.
R,_,
�`
f
'
- ' r'
•�b �
_� . .
'�..�'�.-. 1
�7
� �."'f ' kR,+ � ,
e•
Figure 9.1 Cut the seal cap strap across the rectangles Figure 9.4 Remove the insulation basket and white insu-
next to the disk. For rear vent, skip this step. lation from the center vent pipe.
,�4.�. .
� ` '� "'� �
r.��:'�•�- ..;a�.
� ___ " rj- ` y� 1+�
£�
U �,,
��p�Y'�'^ t., ;^ �►
. .e6�11��l� � .-.
.. � �� . ' - . "- -
Figure 9.2 Remove the white gasket material covering
the seal cap. �'
�r.
1 `. Figure 9.5 Remove the insulation from the outer vent
�"°�„ _ _` � -- - pipe. For rear venting there is no insulation in the outer
-� „ � vent pipe.
���, .� �,-.; , ��
. - - >
-�
- �:.�
rr-.
��`. �
.F✓, � �•�.. . � . . � .
�.
�'
Figure 9.3 Remove the seal cap.
42 Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12
x .
_' ••�,,` . ,` ��
� , , f..' �
� ��
.
- -' � �
;�
� �
_ ��7 � r > x� �'� . � ' ,
� � ,� q� �
Figure 9.6 To attach the first section of vent pipe, make �.,�- , �
sure to use the fiberglass gasket in the manual bag to seal _ •�t'
between the first vent component and the outer fireplace .���' �
wrap. Use 2 self tapping screws to secure the gasket to ' '
the outer wrap. �� - ;;��
Secure the first section of venting to the fireplace by screw- Figure 9.9 Fold the center parts of the retaining band out
ing through the two straps left over from cutting the seal and use to remove the seal cap.
cap strap in step 2.
B. Rear Vent NOTICE:Once the sea/cap has been removed it CANNOT
be reattached.
CAUTION! Risk of Cuts, Abrasions or Flying Debris.
Wear protective gloves and safety g/asses during instal-
lation. Sheet metal edges are sharp. � �
NOTICE: Once appliance is set up for top or rear venting, - � '
it CANNOT be changed at a later time.
• , � ,
_� - , -
c ���`
�y . +
'�;;�� .��;;�
'�
s k,
� ,
-' _ ! =<• s-$ �. _ .
Figure 9.7 Fold the tabs toward the center of the seal
cap (90°) and remove the insulation gasket.
�
-- . �} � .
�''. - ,:,e� �-i
' Figure 9.10 Discard the vent cap, remove and discard
� the insulation basket.
. �
. , ,� ,`
� , ;,
Figure 9.8 Cut the metal retaining band and fold the
sides out.
Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12 43
. • Keep nailing tabs flush with the framing.
.
• Level the appliance from side to side and front to back.
s� • "Square" the unit by securing diagonal dimensions to
,,�
within 1/4 inch of each other. See Figure 9.13.
• Shim the appliance as necessary. It is acceptable to use
,��� wood shims underneath the appliance.
� • Secure the appliance to the framing by using nails or
screws through the nailing tabs.
- �.; �; �, • Secure the appliance to the floor by inserting two screws
��" �'� ,� ;��, � through the pilot holes at the bottom of the appliance.
,.- �
Figure 9.11 Attach the first vent section (it will snap into
place). Slide the insulation gasket onto the vent section, A B
up against the appliance and over the tabs.
C. Installing the Non-combustible Board
The factory supplied non-combustible board spans the dis-
tance from the top of the fireplace to the center of the framing
header. This board must be used. See Figure 9.12.
O O
HEADER
� Note: Diagonal dimensions(A)and(B)must be within
1/4 inch of each other.
,
s
_ Figure 9.13 Positioning the Appliance Squarely
D. Securing and Leveling the Appliance
WARNING!Risk of Fire!Prevent contact with:
• Sagging or loose insulation
• Insulation backing or plastic
• Framing and other combustible materials
. ,
Block openings into the chase to prevent entry of blown- �
in insulation. Make sure insulation and other materials
are secured. 0
DO NOT notch the framing around the appliance
standoffs.
Failure to maintain air s ace clearance ma cause NAILING TABS do�
{� y (BOTH SIDES)
overheating and fire.
The diagram shows how to properly position and secure
the appliance (see Figure 9.15). Nailing tabs are provided PILOTHOLES
to secure the appliance to the framing members.
• B@nd OUt Ilaillllg tabS 011 eaCh Sld@. Figure 9.14 Proper Positioning and Securing of an Appliance
• Place the appliance into position.
44 Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12
10 Installing Vent Pipe (DVP and SLP Pipe)
A. Assemble Vent Sections (DVP Pipe Only) ..� --� ,�
Attach Vent to the Firebox Assembly
Note:The end of the pipe sections with the lanced tabs will face �' _
toward the appliance.
' �
Attach the first pipe section to the starting collar: ` �� �
< � ;�,
• Lanced pipe end to the starting collar - �j ��� �' �'
l� '�� +� ����i
• Inner pipe over inner collar �
• Push the i e section until all lanced tabs sna in lace '�, :`+%���
Pp p p � , ! / -� ,�
• Lightly tug on pipe to confirm it has locked. `
�::
Commercial, Multi-family (Multi-level exceeding two sto- �
ries),or High-Rise Applications =���, �
All outer pipe joints must be sealed with silicone with a Figure 10.1 High Temperature Silicone Sealant
minimum of 300°F continuous exposure rating, including the
slip section that connects directly to the horizontal termi-
nation cap.
• Apply a bead of silicone sealant inside the female outer �
pipe joint prior to joining sections. See Figure 10.1 , A► l..[�-
• Only outer pipes need to be sealed.All unit collar, pipe, �
slip section, elbow and cap outer flues shall be sealed ''{ �
in this manner, unless otherwise stated. � �"`'�
�_
=
WARN/NG!Risk of Fire or Explosion!DO NOT break I B I .�.�a
silicone seals on slip sections. Use care when remov- �
ing termination cap from slip pipe. If slip section seals \ �
are broken during removal of the termination cap, vent � `�—�
171ay 12ak. Figure 10.2 Figure 10.3
Assemble Pipe Sections
Note: Make sure that the seams are not aligned to prevent
Per Figure 10.2: unintentional disconnection.
• Start the inner pipe on the lanced end of section A into
the flared end of section B. , � `�
�
• Start the outer pipe of section A over the outer pipe of -
section B. � `
• Once both vents sections are started, push firmly until �
�
all lanced tabs lock into place.
• Lightly tug on the pipe to confirm the tabs have locked. � �� ;,�
It is acceptable to use screws no longer than 1/2 in. (13
mm)to hold outer pipe sections together. If predrilling holes, CORRECT
DO NOT penetrate inner pipe.
._ �. .,-_..._.,.
For 90°and 45°elbows that are changing the vent direction �
from horizontal to vertical, one screw minimum should be ___ _
put in the outerflue at the horizontal elbowjoint to prevent E _ -
the elbow from rotating. Use screws no longer than 1/2 ,
in. (13 mm). If predrilling screw holes, DO NOT penetrate _ � '
inner pipe.
Figure 10.4 Seams INCORRECT
Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12 45
B. Assemble Vent Sections (SLP Pipe Only) C. Assemble Slip Sections
To attach the first vent component to the starting collars • Slide the inner flue of the slip section into the inner flue of
of the appliance: the pipe section and the outer flue of the slip section over
• Attach a DVP-2SL or DVP-SLP24 adapter to the starting the outer flue of the pipe section. See Figure 10.6.
collar of the appliance. • Slide together to the desired length.
• Lock the vent components into place by sliding the pipe
section onto the collar.
• Align the seam of the pipe and seam of collar to allow '
engagement. Rotate the vent component to lock into � .
place. Use this procedure for all vent components. See t��, , -,
Figure 10.5.
� � _ -
�
• Slide the gasket over the first vent section and place it '���`�'
flush to the appliance.This will prevent cold air infiltration.
Caulk with a minimum of 300°F continuous exposure rating �'"
may be used to hold the part in place. [�,�Q�
• Continue adding vent components, locking each
succeeding component into place. Figure�o.s siip section Piiot Hoies
• Ensure that each succeeding vent component is securely • Maintain a 1-1/2 in. (38 mm) overlap between the slip
fitted and locked into the preceding component. section and the pipe section.
Commercial, Multi-family (Multi-level exceeding two sto- • Secure the pipe and slip section with two screws no
ries),or High-RiseApplications longer than 1/2 in. (13 mm), using the pilot holes in the
For Installation into a commercial, multi-family(multi-level slip section. See Figure 10.7.
exceeding two stories)or high-rise applications: All outer
pipe joints must be sealed with silicone with a minimum of
,•, -
300°F continuous exposure rating, including the slip section `�'''
that connects directly to the horizontal termination cap.
• Apply a bead of silicone sealant inside the female outer
pipe joint prior to joining sections. See Figure 10.1. "'` `
• Onl outer i es need to be sealed.All unit collar, i e, �� .� Y '��
Y P P P�p E;;t<=.
slip section, elbow and cap outer flues shall be sealed
in this manner, unless otherwise stated.
WARNING!Risk of Fire or Explosion!DO NOT break ' a. •t��� �
�,�, �_:�_''
silicone seals on slip sections. Use care when remov- "�,��°
ing termination cap from slip pipe. If slip section seals
are broken during removal of the termination cap, vent
may leak.
Figure 10.7 Screws into Slip Section
� • Continue adding pipe as necessary following instructions
. .
in "Assembling Pipe Sections."
� � NOTICE:If slip section is too long, the innerand outer flues
of the slip section can be cut to the desired length.
, .
NOTICE: When installing a vent system with an HRC
�� 'E termination cap, all pipe system joints shall be sealed
using silicone sealant with a minimum of 300°F continuous
Note: Align seams to engage pipe, exposure rating.
then rotate counterclockwise to lock • Apply a bead of silicone sealant inside the female outer
Figure 10.5 Adding Venting Components pipe joint prior to joining sections.
• Only outer pipes are sealed, sealing the inner flue is not
required.
• All unit collar, pipe, slip section, elbow and cap outer
flues shall be sea/ed.
46 Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12
D. Secure the Vent Sections E. Disassemble Vent Sections
• Vertical runs of DVP pipe must be supported every 8 ft. • Rotate either section (see Figure 10.10) so the seams
(2.44 m)after the 25 ft. (7.62 m)maximum unsupported on both pipe sections are aligned as shown in Figure
rise. 10.11.
• Vertical runs of SLP pipe must be supported every 8 ft. • Pull carefully to separate the pieces of pipe.
(2.44 m).
• Horizontal sections must be supported every 5 feet
(1.52 m). - -
�F
• Vent supports or plumbers strap (spaced 120° apart) ,� _
may be used to support vent sections. See Figures 10.8 '��`� — —
and 10.9. :;�';r:� �
• Wall shield firestops may be used to provide horizontal � `
support vent sections. ; ,�
• SLP ceiling firestops have tabs that may be used to - -_-�-- .-r �' -.$�r�°
provide vertical support. � � _
";�'
WARNING! Risk of Fire, Explosion or Asphyxiation! - - � ;
. ,::. . . ,. � ..;.
Improper support may allow vent to sag and separate. �`''�""��`'`'�"� "' ' � � � �-�" " -"""
P
Use vent run supports and connect vent sections per in- - - -
stallation instructions. DO NOT allow vent to sag below Figure 10.10 Rotate Seams for Disassembly
connection point to appliance.
,zo� M
- � r
� �� �— �� — —
�
- � - �
i --
� . : _�
, ; �
Y_ .i. �
Figure 10.11 Align and Disassemble Vent Sections
Figure 10.8 Securing Vertical Pipe Sections
120°
� �
�_� �
Figure 10.9 Securing Horizontal Pipe Sections
Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12 47
F. Install Decorative Ceiling Components
(SLP only) LEVEL
A decorative ceiling thimble can be installed on a flat ceil- caTHeoRa�ceiuNc
ing through which the vent passes. The decorative ceiling � � � SUPPORT BOX
thimble is used to cover the firestop.
• Seal the gap between the vent pipe and firestop using m
silicone with a minimum of 300°F continuous exposure
rating to prevent cold air infiltration.
• Install the decorative ceiling thimble by sliding it up to � 2 in.(51 mm) MIN.BELOW
the ceiling and attaching it using the provided screws. FiNisHe�ceiuN�
Adecorative cathedral ceiling support box can be installed �
on a cathedral ceiling through which the vent passes. cuT Ho�e vs�n.�s mm►
GREATER IN SIZE THAN �
• Use a plumb-bob to mark the center line of the venting PATTERN OF SUPPORT
s stem on the ceilin and drill a small hole throu h the BOXAS IT IS PROJECTED
Y 9 g ONTO ROOF LINE =� c
ceiling and roof at this point. Locate the hole and mark
the outline of the cathedral ceiling support box on the
outside roof.
Figure 10.12
• Remove shingles or other roof covering as necessary
to cut the rectangular hole for the support box. Cut the
hole 1/8 in. (3 mm) larger than the support box outline.
• Lower the support box through the hole in the roof until its
bottom is at least 2 in. (51 mm)below the ceiling (Figure
10.12).
• Level the support box both vertically and horizontally and
temporarily tack it in place through the inside walls into
the roof sheathing.
• Use tin snips to cut the support box from the top corners
down to the roof line and fold the resulting flaps to the
roof. See Figure 10.13.
• Nail the flaps to the roof AFTER running a bead of non
hardening sealant between the flaps and the roof.
WARNING! Risk of Fire! Clean out ALL materials from Figure 10.13
inside the support box and complete the vertical vent run
and termination.
48 Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12
G. Install Metal Roof Flashing
-,
• See minimum vent heights for various pitched roofs •
(Figure 10.14)to determine the length of pipe to extend i '
through the roof. '� + �
�
• Slide the roof flashing over the pipe sections extending �� �
through the roof as shown in Figure 10.15. � �
HORIZONTAL �
OVERHANG
2 FT. 20 INCHES MIN.
MIN. VERTICAL
WALL
LOW EST ��� '
DISCHARGE
OPENING
GAS DIRECT VENT
TERMINATION CAP H. Assemble and Install Storm Collar
X CAUTION! Risk of Cuts, Abrasions or Flying Debris.
12 Wear protective gloves and safety glasses during instal-
LROOF PITCH lation. Sheet metal edges are sharp.
�s �v,z • Connect both halves of the storm collar with two screws
H(MIN.)-MINIMUM HEIGHT FROM ROOF (see Figure 10.16).
TO LOWEST DISCHARGE OPENING
• Wrap the storm collar around the exposed pipe section
closest to the roof and align brackets. Insert a bolt
(provided) through the brackets and tighten the nut to
complete the storm collar assembly. Make sure the collar
Roof Pitch H (Min.) Ft. is tight against the pipe section.
Flat to 6/12........................................1.0' • Slide the assembled storm collar down the pipe section
Over 6/12 to 7/12............................1.25* until it rests on the roof flashing (see Figure 10.17).
Over 7/12 to 8/12..............................1.5' • Caulk around the top of the storm collar(see Figure 10.18).
Over 8/12 to 9/12..............................2.0*
Over 9/12 to 10/12.............................2.5
Over 10/12 to 11/12.........................3.25
Over 11/12 to 12/12...........................4.0 �
Over 12/12 to 14/12...........................5.0 �
Over 14/12 to 16/12...........................6.0 � "
r
Over 16/12 to 18/12...........................7.0 'a;;�
Over 18/12 to 20/12...........................7.5 „�,.
��- Brackets
Over 20/12 to 21/12...........................8.0 "� � /
'3 foot minimum in snow regions �� -�
Figure 10.14 Minimum Height From Roof To Lowest Discharge
Opening
G�pQa9(�9(3 G�C{��C�
NOTICE: Failure to properly caulk the roof flashing and '- �' :�, . -
pipe seams may permit entry of water. �� � �v,�
�� � �£;,r�'
• Caulk the gap between the roof flashing and the outside � s ���� ;�� .�,
diameter of the pipe. ,. Y�f�;Y ���
. �i��c qi.:��
• Caulk the perimeter of the flashing where it contacts the {' �r: �
��
roof surface. See Figure 10.15. - -
• Caulk the overlap seam of any exposed pipe sections
that are located above the roof line. � �'�'' �
�`�
j�
:4,7 y ,i���.
.T �.
I � • • � • �•
Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12 49
I. Install Vertical Termination Cap K. Heat Shield Requirements for Horizontal
• Attach the vertical termination cap by sliding the inner Termination
collar of the cap into the inner flue of the pipe section WqRNING!Risk of Fire!To prevent overheating and fire,
while placing the outer collar of the cap over the outer heat shields must extend through the entire wall thick-
flue of the pipe section. ness.
• Secure the cap by driving three self-tapping screws • DO NOT remove the heat shields attached to the
(supplied) through the pilot holes in the outer collar of wall shield firestop and the horizontal termination cap
the cap into the outer flue of the pipe(see Figure 10.18). (shown in Figure 10.20).
• Heat shields must overlap 1-1/2 in. (38 mm) mini-
TERMINATION CAP mum.
- There are two sections of the heat shield. One section
� I ---�.j �, is factory-attached to the wall shield firestop. The other
' section is factory-attached to the cap. See Figure 10.20.
� ' If the wall thickness does not allow the required 1-1/2 in.
� ' , (38 mm) heat shield overlap when installed, an extended
� � � heat shield must be used.
f ; ;;� �
� I • If the wall thickness is less than 4 in./102 mm (DVP)
or 4-3/8 in./ 111 mm (SLP), the heat shields on the cap
(1 of 3) and wall shield firestop must be trimmed. A minimum
� 1-1/2 in. (38 mm)overlap MUST be maintained.
'� • Use an extended heat shield if the finished wall thickness
STORM is greater than 7-1/4 in. (184 mm).
COLLAR
j ' ,'� • The extended heat shield may need to be cut to length
scRews maintaining sufficient length for a 1-1/2 in. (38 mm)
cau�K `� f,; ,� overlap between heat shields.
' • Attach the extended heat shield to either of the existing
�j heat shields using the screws supplied with the extended
- = heat shield. Refer to vent components diagrams in the
�� - back of this manual.
• Rest the small leg on the extended heat shield on top
.1. Install Decorative Wall Components (SLP of the pipe section to properly space it from the pipe
section.
only)
A decorative wall thimble can be installed on wall through Important Notice: Heat shields may not be field constructed.
which the vent passes.The decorative wall thimble is used
to cover the wall shield firestop.
• Slide the decorative wall thimble over the last section of
horizontal pipe before connecting the termination cap to
the pipe.
• Once the pipe section and the termination cap have
been connected, slide the wall thimble up to the interior
wall surface and attach with screws provided.See Figure
10.19.
Figure 10.19 Wall Thimble
50 Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12
L. Install Horizontal Termination Cap (DVP Note: When using termination caps with factory-supplied
and SLP Pipe) heat shield attached, no additional wall shield firestop is
required on the exterior side of a combustible wall.
WARNING! Risk of Fire! The telescoping flue section of
the termination cap MUST be used when connecting vent.
• 1-1/2 (38 mm) minimum overlap of flue telescoping
HEAT SHIELD OR HEAT SHIELD
SP.CfIOI�I IS I�P.CrUIYP.d. EXTENDED 1-1/21N.(38 MM)MIN.
HEAT SHIELD OVERLAP
Failure to maintain overlap may cause overheating and �N.4LL SHIELD
FIRESTOP /
fire. � �
�
• Vent termination must not be recessed in the wall.Siding �� -
may be brought to the edge of the cap base. � - ----- - ,
SLIP SECTION
• Flash and seal as appropriate for siding material at CANBEEXTENDED
outside edges of cap. -
• When installing a horizontal termination cap, follow INNERVENT SHEATHING
the cap location guidelines as prescribed by current OUTERVENT
INTERIOR EXTERIOR
ANSI Z223.1 and CAN/CGA-B149 installation codes
and refer to Section 6 of this manual.
C A�/7'IO�I� I�/Sk �f Bu�,ns� I�L,a� L,�,./es may�-e�yU��•e �n- VENT DEPTH FROM BACK OF APPLIANCE TO
iy v nr rc � u .� E OUTSIDE SURFACE OF EXTERIOR WALL�
stallation of a cap shield to prevent anything or anyone (SEECHARTBELOW)
from touching the hot cap.
Figure 10.20 Venting through the wall
NOTICE: For certain exposures which require superior
resistance to wind-driven rain penetration,a flashing kit and
HRC caps are available. When penetrating a brick wall, a Cap Specification Chart
(depth without using additional pipe sections)
brick extension kit is available for framing the brick.
DVP-TRAPK1 DVP-TRAP1 DVP-TRAPK2 DVP-TRAP2
Top Vent Rear Vent Top Vent Rear Vent
Depth Depth Death Depth
2-3/4 in.to 3-1/8 in.to 5-1/8 in.to 5-1/2 in.to
6000 4-5/8 in. 5 in. 9-1/8 in. 9-1/2 in.
Series
8000
Series DVP-HPC1 DVP-HPC1 DVP-HPC2 DVP-HPC2
Top Vent Rear Vent Top Vent Rear Vent
Depth Depth Depth Depth
2-3/4 in.to 3-1/8 in.to 4-7/8 in.to 5-1/4 in.to
4-7/8 in. 5-1/4 in. 9 in. 9-3/8 in.
DVP-TRAP1 can adjust 1-1/2 in.(3-1/8 to 4-5/8 in.)
DVP-TRAP2 can adjust 4 in.(5-3/8 to 9-3/8)
DVP-HPC1 can adjust 2-1/8 in.(4-1/4 to 6-3/8)
DVP-HPC2 can adjust 4-1/8 in.(6-3/8 to 10-1/2)
Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12 51
11 Gas Information
A. Fuel Conversion C. Gas Connection
• Make sure the appliance is compatible with available gas • Refer to Reference Section 16 for location of gas line
types. access in appliance.
• Conversions must be made by a qualified service • Gas line may be run through knockout(s) provided.
technician using Hearth&Home Technologies specified . The gap between supply piping and gas access hole may
and approved parts. be caulked with caulk with a minimum of 300°F continuous
B. Gas Pressure exposure rating or stuffed with non-combustible,unfaced
• Optimum appliance performance requires proper input
insulation to prevent cold air infiltration.
pressures. • Ensure that gas line does not come in contact with outer
• Gas line sizing requirements will be determined in ANSI Wrap of the appliance. Follow local codes.
Z223.1 National Fuel Gas Code in the USA and CAN/ • Pipe incoming gas line into valve compartment.
CGA B149 in Canada. • Connect incoming gas line to the 1/2 in. (13 mm)
• Pressure requirements are: connection on manual shutoff valve.
Wi4RN/NG! Risk of Fire or Explosion! Support control
Gas Pressure Natural Gas Propane when attaching pipe to prevent bending gas line.
Minimum inlet pressure 5.0 in.w.c. 11.0 in.w.c. • A small amount of air will be in the gas supply lines.
Maximum inlet pressure 10.0 in.w.c. 13.0 in.w.c. WARNING!Risk of Fire or Explosion!Gas build-up dur-
Manifold pressure 3.5 in.w.c. 10.0 in.w.c. ing line purge could ignite.
• Purge should be performed by qualified service
Wi4RNING! Risk of Fire or Explosion! High pressure technician.
will damage valve. Low pressure may cause explosion. • Ensure adequate ventilation.
• Verify inlet pressures. Verify minimum pressures when • Ensure there are no ignition sources such as sparks
other household gas appliances are operating. or open flames.
• Install regulator upstream of valve if line pressure is Light the appliance. It will take a short time for air to purge
greater than 1/2 psig. from lines. When purging is complete the appliance will
light and operate normally.
A WARN I NG WARNING! Risk of Fire, Explosion or Asphyxiation!
Check all fittings and connections with a non-corrosive
Fire Risk. commercially available leak-check solution. DO NOT use
Explosion Hazard. open flame. Fittings and connections could have loos-
High pressure will damage valve. ened during shipping and handling.
• Disconnect gas supply piping BEFORE WARNING!Risk of Fire!DO NOT change valve settings.
pressure testing gas line at test pressures This valve has been preset at the factory.
above 1/2 psig.
• Close the manual shutoff valve BEFORE
pressure testing gas line at test pressures
equal to or less than 1/2 psig. D. High Altitude Installations
NOTICE:If the heating value of the gas has been reduced,
Note: Have the gas supply line installed in accordance with these rules do not apply. Check with your local gas utility
local codes, if any. If not, follow ANSI 223.1. Installation or authorities having jurisdiction.
should be done by a qualified installer approved and/or �/hen installing above 2000 feet elevation:
licensed as required bythe locality. (In the Commonwealth
of Massachusetts installation must be perFormed by a • In the USA: Reduce burner orifice 4°/o for each 1000 feet
licensed plumber or gas fitter). above 2000 feet.
Note: A listed (and Commonwealth of Massachusetts ap- • In CANADA: Reduce burner orifice 10% for elevations
proved) 1/2 in. (13 mm) T-handle manual shut-off valve between 2000 feet and 4500 feet. Above 4500 feet,
and flexible gas connector are connected to the 1/2 in. (13 consult local gas utility.
mm) control valve inlet.
• If substituting forthese components,please consult
local codes for compliance.
52 Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12
1 Z Electrical Information
A. Wiring Requirements B. IntelliFire PIusT'" Ignition System Wiring
NOTICE: This appliance must be electrically wired • �Nire the appliance junction box to 110 VAC for proper
and grounded in accordance with local codes or, in the operation of the appliance.
absence of /oca/ codes, with National Electric Code WqRNING!Risk of Shock or Explosion!DO NOT wire
ANSI/NFPA 70-latest edition or the Canadian Electric IPI controlled appliance junction box to a switched circuit.
Code CSA C22.1. Incorrect wiring will override IPI safety lockout.
• Wire the appliance junction box to 110-120 VAC.This is • Refer to Figure 12.2, IPI Wiring Diagram.
required for use of optional accessories (standing pilot
ignition) or proper operation of the appliance (IntelliFire • This appliance is equipped with an IntelliFire PIusT"'
PIusT"' ignition). control valve which operates on a 6 volt/1.5 AMP
system.
• A 110-120 VAC circuit for this product must be protected
with ground-fault circuit-interrupter protection, in • Plugthe6volttransformerplugintotheappliancejunction
compliance with the applicable electrical codes, when box to supply power to the unit OR install 4 AA cell
it is installed in locations such as in bathrooms or near batteries (not included) into the battery pack before use.
sinks.
• Low voltage and 110 VAC voltage cannot be shared C. Standing Pilot Ignition System Wiring
within the same wall box. • The standing pilot ignition system wiring does not require
W�IRNING!Risk of Shock or Explosion!DO NOT wire a 110 VAC supply to operate. See Figure 12.3
110V to the valve orto the appliance wall switch. Incorrect • A 110 VAC junction box MUST be installed for use with
wiring will damage controls. a fan or remote control. See Figure 12.4 forjunction box
Determine if the appliance uses an IntelliFire PIusT"" igni- wiring. Keep wire lengths short as possible.
tion system or standing pilot ignition system: NOTICE:DO NOT wire 110 VAC to the millivolt valve!This
• Open the control access panel or remove the decorative will damage the valve.
front. • If using a thermostat use one compatible with a millivolt
• A red or black ignitor button (as shown in Figure 12.1) gas valve system:
indicates this appliance is standing pilot ignition. - Install the thermostat in the location as indicated in the
thermostat instructions to ensure proper operation of
appliance.
RED OR - USe low resistance thermostat wire for wiring from
= BLACK
BUTTON ignition system to the wall switch and thermostat.
- Keep wire lengths short as possible.
0
� o m
ao
D. Optional Accessories Requirements
� � • This appliance may be used with a wall switch, wall
mounted thermostat and/or a remote control.
Wiring for optional Hearth&Home Technologies approved
Figure 12.1 Ignitor Button accessories should be done now to avoid reconstruction.
Follow instructions that come with those accessories.
• Hearth & Home Technologies recommends that Intel-
IiFire PIusT"'wireless controls be used for their features
and functionality with the IntelliFire PIusT"' ignition sys-
tem.
• A standard ON/OFF switch is compatible.
Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12 53
FLAME
SENSE �GNITER
TO JUNCTION
BOX(110V)
MODULE
� '�� � oop�
0 -
FLAME m `~ �
o MODULATION
O RC100 RC200
(OPTIONAL WALL CONTROLS)
�
0
ORANGE GREEN BATTERY PACK
(PILOT) (MAIN)
6V DC
BLACK �
RED THERMOSTAT WIRE
ASSEMBLY/WALL
BROWN SWITCH WIRE
I � GROUND
Figure 12.2 IPI Wiring Diagram
STANDING
PILOT
� ��� BRN ¢'�
� �I
0 0, RED
VALVE ON/OFFPIGGYBACK WIRE
WHT THERMOSTAT
RED WIRE ASSEMBLY/WALL
SWITCH WIRE
Figure 12.3 Standing Pilot Ignition Wiring Diagram
54 Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12
E. Electrical Service and Repair
WARNING! Risk of Shock! Label all wires prior to dis-
connection when servicing controls. Wiring errors can Romex
cause improper and dangerous operation. Verify proper Connector
operation after servicing. i°'i �
� ., �► 14/2WG
WARNING!Risk of Shock!Replace damaged wire with �^
o i
type 105°C rated wire. Wire must have high temperature 0 a i � I Cover Plate
InsUlatlon. � �� " outside firebox
♦
F. Junction Box Installation
� o
If the box is being wired from the INSIDE of the appliance: �'�
m
• Remove the screw attaching the junction box/receptacle to = Y
the outer shell,rotate the junction box inward to disengage �' °° - Copper
it from the outer shell (see Figure 12.4). � � � �GRN wire 9round attached
• Pull the electrical wires from outside the appliance through �e�a inside box to GRN screw with
the opening into the valve compartment and secure wires � GRnI wire
with a Romex connector. See Figure 12.4.
• Make all necessary wire connections to the junction box/ NOTICE: DO NOT wire
receptacle and reattach the junction box/receptacle to the 110 VAC to wall switch,
OUtel'Sh211. Figure 12.4 Junction Box Detail
G. Wall Switch Installation for Fan (Optional)
If the box is being wired to a wall mounted switch for use
with a fan (See Figure 12.5): sW�c�n
Minimum 14-3 AWG �
• The power supply for the appliance must be brought into with Ground
a switch box. � Black Black
Whi[e White
Junction Box Green
• The power can then be supplied from the switch box to the �
appliance using a minimum of 14-3 with ground wire. �m��
• At the switch box connect the black (hot) wire and red 6 a 3= � `'�"'""` o sw�tcn BoX Supply
(switch leg)wire to the wall switch as shown. o ��a ��a �a w��es
• At the appliance connect the black (hot), white (neutral) � 5 ° ' ' ' �«T Knockout
and green (ground)wires to the junction box as shown.
• Add a 1/4 in. insulated female connector to the red(switch Red
leg) wire, route it through the knockout in the face of the
junction box, and connect to the top fan switch connector Figure 12.5 Junction Box Wired to Wall Switch or BC10
(1/4 in. male)as shown.
Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12 55
13 Finishing
A. Mantel and Wall Projections B. Facing Material
Wi4RNING! Risk of Fire! Comply with all minimum clear- • Metal front faces may be covered with non-combustible
ances as specified. Framing closer than the minimums list- materials only.
ed mustbe constructed entirelyofnoncombustible materials • Facing and/or finishing materials must not interFere with
(i.e., steel studs, concrete board, etc.) air flow through louvers, operation of louvers or doors,
Combustible Mantels or access for service.
• Facing and/or finishing materials must never overhang
into the glass opening.
Note:All TO CEILING • Observe all clearances when applying combustible
measurements
in inches. �$ materials.
�2 • Seal joints between the finished wall and appliance top
1011 3Z and sides using a 300°F minimum sealant. Refer to
9 Figure 13.3.
8 25
6 ' �9 WARNING! Risk of Fire! DO NOT apply combustible
5 17 18 materials beyond the minimum clearances. Comply with
3 4 1516 all minimum clearances to combustibles as specified in
,a this manual. Overlapping materials could ignite and will
13 interfere with proper operation of doors and louvers.
72
2-1/2 11
� 10
5 � B
FACTORY-INSTALLED NON-COMBUSTIBLE BOARD
� MEASUREMENTS FROM DO NOT REMOVE ,��
TOP EDGE OF THE OPENING
Note: Measurement is taken from top of the opening,
NOT the top of the fireplace.
Figure 13.1 Minimum Vertical and Maximum Horizontal
Dimensions of Combustibles
A
Combustible Mantel Legs or Wall Projections
INTERIOR WALL
TOP VIEW �
� ' � �
�F l�
A 6
�l A B
� inches 39-3/4 41
FIREPLACE OPENING 6000
� millimeters 1010 1041
inches 41-3/4 48
MANTEL LEG OR WALL PROJECTIONS HOOO
millimeters 1060 1219
If A minimum is_,then B maximum is Figure 13.3 Noncombustible Facing Diagram
A Inches 2-7/16 3-7/16 4-7/16 5-7/16 6-7/16 7-7/16
Millimeters 62 87 113 138 164 189
m�hes 1 2 3 4 5 ao
B Millimeters 25 51 76 102 127 bo
Figure 13.2 Combustible Mantel Leg or Wall Projections
(Acceptable on both sides of opening)
56 Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12
C. Doors Finishing Material:
Only doors certified for use with this appliance model may 1 Inch Thick or Less
be used. Contact your dealer for a list of doors that may Remove Finishing Strips. See Figure 13.7.
be used. Once you have determined what kind of door
and finishing material is going to be used on the fireplace, NOTICE: Remove finishing strips before firing appliance.
you may use the table below which shows the door mod-
els and the finishing material thickness allowed.
DOOR FIT FINISH MATERIAL SEE �►
THICKNESS FIGURE
Folio Inside Any 13.6
Overlap 1 inch or less 13.4 �
Arcadia �
Inside Greater than 1 inch 13.5
Overlap 1 inch or less 13.4 1 in.MAX.
Halston DOOR FINISHING MATERIAL
Inside Greater than 1 inch 13.5 (TOP EDGE)
Overlap 1 inch or less 13.4 Finishing materials 1 inch maximum thick.
Chateau
Inside Greater than 1 inch 13.5 Stop finishing material flush with opening.
Overlap 1 inch or less 13.4
MT Hammer
Inside Greater than 1 inch 13.5
Overlap 1 inch or less 13.4
Galleria FINISHING STRIP NOT USED
Inside Greater than 1 inch 13.5 (See Figure 13.7 for
CF Inside Any 13.6 •, removal instructions)
0
NON-COMBUSTIBLE
FINISHING MATERIAL
Note: Finishing strips may be used to aid in positioning of
non-combustible facing materials for some of the facing and
door combinations specified in the table above. They must
be removed following finishing work. See figure 13.7.
0.
Figure 13.4 Finishing Material 1 Inch Thick or Less
Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12 57
Finishing Material Thickness: Finishing Material Thickness:
1-4 inches maximum 0-4 inches maximum
NOTICE: Remove finishing strips before firing appliance. NOTICE:Remove finishing strips before firing appliance.
j FINISHING
�� �STRIPS USED '
� FINISHING STRIP NOT USED
I — (See Figure 13.7 for
� : removal instructions)
i NON-COMBUSTIBLE
FINISHING MATERIAL
NON-COMBUSTIBLE
I / FINISHING MATERIAL
/i
\_�
G.
_ �
�.
FINISHING ' � ' FINISHING
MATERIAL MATERIAL
�
DOOR
A �(Outside door width) ' '
�E C �
(Includes 1I8 in.opening each side of door)
� �
000000
����� DOOR
FINISHING MATERIAL FINISHING MATERIAL
Figure 13.6 Folio/CF Inside Fit
0 B 8000 Models 6000 Models
� A � Inches Millimeters Inches Millimeters
(outsidedoorwidth) A 44-1/16 1119 37-1/16 941
B 35-15/16 913 34-1/16 865
0 C 44-5/16 1126 37-5/16 948
�-E C -� D 36-5/16 922 34-7/16 882
(Includes 1/8 in.opening each side of door)
Finishing material thickness, 1-4 inches maximum
B=Top of door to bottom of fireplace.
D= Bottom of Finishing Material to Bottom of Fireplace
Figure 13.5 Finishing Material Thickness Greater Than One Inch
58 Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12
Removal of Finishing Strips
NOTICE: Remove finishing strips before firing appliance.
Remove glass frame assembly to access finishing strip
scre ws.
FINISHING STRIPS REMOVED
� !�
,� O ` � ,,�
.
D
� . � � �
�
D'
el � I ��.
�B
Figure 13.7 Removing Finishing Strips.
31-718 IN.(6000)
33-11/161N.(8000)
3-314 IN.
6000,8000
A
35-5/16 IN.(6000)
431N.(8000)
Figure 13.8. Clean Face Door Dimensions
Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12 59
D. Elevated Hearth Systems
Use the table below to identify the hearth system that will be used. The table will also help identify effects on the various
dimensions. Some hearth systems will elevate the appliance off the floor at a given dimension. For example, if appliance
will be used with a Kenwood Cabinet with Base, the appliance will be elevated 9-1/4 in. The 9-1/4 in. elevation will also
have to be added to the following: Wall penetration referenced in Figure 8.2 (Wall penetration) and Rough Opening Height
(header height) referenced in Figure 5.2. Note: Finished floor thickness should also be considered when determining in-
stallation dimensions.
ELEVATED APPLIANCE MARBLE LEG CUT
MODEL DESCRIPTION PART# DIMENSION LENGTH
See Note 1 See Note 2
KENWOOD CABINET KDC48DBP 0 33 in.
KENWOOD CABINET W/BASE KDC48DBP W/HTKDC48DBP 9-1/4 in. 33 in.
KENWOOD CORNER CABINET KDA48DBP 0 33 in.
6000 KENWOOD CORNER CABINET W/BASE KDA48DBP W/HTKDA48DBP 9-1/4 in. 33 in.
Series
KENWOOD MANTEL AFKDMPB 0(See Note 3) 33 in.
KENWOOD MANTEL W/BASE AFKDMPB W/HTKDMPB 9-1/4 in. 33 in.
LUNA SURROUND LUNA-36-GY 1-1/16 in. N/A
8000 KENWOOD MANTEL AFKDMPC 0(See Note 3) 32-7/8 in.
Series KENWOOD MANTEL W/BASE AFKDMPC W/HTKDMPC 9-1/4 in. 32-7/8 in.
Note 1. Add dimensions to Wall Penetration (Figure 8.2) and Rough Opening Height (Figure 5.2).
Note 2. Verify Marble Cut Lengths on site prior to cutting.
Note 3. Dimensions assume use of a 3/4 in. Hearth Pad.
60 Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12
14 Appliance Setup
A. Remove Fixed Glass Assembly F. Ember Placement
See Section 14.H. WARNING! Risk of Explosion!Follow ember placement
instructions in manual. DO NOT completely block burner
B. Remove the Shipping Materials ports with ember material. Replace ember material annu-
Remove shipping materials from inside or underneath the ally. Improperly placed embers interfere with proper burner
firebox. operation.
C. Clean the Appliance Ember material is shipped with this gas appliance.To place
the ember material:
Clean/vacuum any sawdust that may have accumulated
inside the firebox or underneath in the control cavity. • Embers CANNOT completely block burner ports. Care
should be taken not to block the lighting trail of ports.
D. Accessories
• Embers may only be placed in areas as shown in Figure
Install approved accessories per instructions included 14.2.
with accessories. Contact your dealer for a list of ap- . LP Only: Using dime-size pieces of Glowing Embers0,
proved accessories.
overlap the burner ports(see Figure 14.3).The impingement
W�IRNING!Risk of Fire and Electric Shock!Use ONLY created by the embers will help blend the fire.
Hearth & Home Technologies-approved optional acces- . Save the remaining ember materials for use during
sories with this appliance. Using non-listed accessories appliance servicing. The embers provided should be
could result in a safety hazard and will void the warranty. enough for 3 to 5 applications.
� E. Burner Top Installation
1. Bend the two tabs upward as shown in Figure 14.1. EMBERs
NO EMBERS IN SHADED AREAS
2. To install the fiber burner, mate the locating holes with
the guide sleeves. Install fiber burner top so that it
makes full contact with the underlying burner assem- Qo�00
�'°°o ° �o°o
bly. oo°000 00�o
°oo°oo o°o°o
3. Ensure that the ports in the steel burner are visible o�o�oo°oo�o
�° °�o° o�o
through the holes in the fiber burner top. °�OOog o°�000
0 0� ° � o
00
00 0�
o°o
FIBER BURNER TOP LOCATING HOLES
oo���
���°° � oo��o
o � Figure 14.2 Placement of Embers
\�V ,�
\� ly���
tiJ �' O O O O
BEND TABS UP
� ,�AIR SCOOP � O
�
i
/
�
BURNER ASSEMBLY .�PILOT COVER
� �
\ BURNER SHIELD O �
� o c
� Q _
GUIDE SLEEVES
' O
Figure 14.3 Embers Overlapping Burner Port Holes(LP only).
Figure 14.1
Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12 61
G. Install the Log Assembly Log Assembly: LOGS-6C
Models: 6000C-IPILP, 6000CBV-IPI
6000C, 6000C-IPI
FIBER BURNER TOP ��CATING HOLES �
i� \
ov�/
./ TABBENTIN=NG LOG PLACEMENT TABS
\�° oo��°° . .
\\�v�° � �
$�°°�oo,a o0
.. . . � i i:':�
BURNER SHIELD PILOT COVER � - - �
B°R"ER"ssE'"B�'' ' � �� LOG PLACEMENT INDENTATIONS
� , ` � � � .
�
. /AB NOT eENT=LP ' I
\ _ .
G � . �� �'�� � - .
GUIDESLEEVES \ �
� GRATE TINE
Figure 7 Figure 2. Log Placement Tabs
CAUTION: Logs are fragile, handle with care. Log#1 (SRV2164-701): Locate log placement tabs on the pilot cover. Bend
tabs upward as shown in Figure 2. Locate the log placements slots on the bottom of Log# 1 (see Figure 3). Mate the slots
located on the bottom of Log #1 with the log placement tabs on the pilot cover. Log # 1 is properly installed when it sits
squarely and completely on pilot cover with tabs engaged (see Figure 4).
- ,,
.. 4K...-� '' ` �,` }; LOG PLACEMENT TABS �
� ; _
, , �
. � }�sx�� ..�'''- .v
�.N� �.aT .. .
.J'
.F �,� l��, �'�, ^ �
fi
,.����� � � � , � y � �
�� ��` ���i � � � � � �K � �� � .
...Y �:} � . . 'S. '�—a , �,���'.
���'. _ . . . _
�
LOG PLACEMENT SLOTS �� �
Figure 4 shows the log placement tabs located on the top of Log # 1. The tabs will be mated with the slots located on the
bottom of Log#2 and Log#3 (see Figure 5). Log#2 and Log#3 also have grooves that allow the logs to be seated properly
on the grate (see Figure 5). Hold Log #1 upright while placing Log #2.
,:,�' ' _ ,* �' . x , r,�
Bottom view of "+, : -m.. __ a
Logs#'2 and 3 � � '�_ •-'
k ��� .g.�z -r �
< ' `�'���'
♦ �°
�L'E,F�T GR�4TE TINE .�''' "
�K . SLOTS �:. �- '� -:"
'� ,,;
- � ' 2 2 _ . ���ti�
3 ,;! . _ , �
� �
' `�'y GROOVES ��. �
� �
��. r �=� ���
r_, f h
� , �i�:. �F
, , , -_
y ��,` j ��^ ;.&.. �� ;y �...
V � ' ' �� �/'� � � ' ff�„ �j ; �.
� � y, 4.
l 7��� ,ao�$ ��i o�5 4. d i�� EL.c�� �Y
.t�l � R'
Log#2 (SRV2164-702): Mate the slot located on the bottom of Log #2 with the left tab on top of Log#1. After slot and tab
have been fitted together, mate the groove located on the bottom of Log #2 with the horizontal grate bar and slide Log #2
toward the left until it rests against the far left grate tine.
62 Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12
�os�
° � _ -' RIGHT GRATE TINE ,�` ` '° °� .,: "��°°
�� �-�r»- �^
, ,
, . :_ . ._ -
, _
�," � r �
����>;
_,
1�•����- ' • � '
,, �
. 3 '
. ;
. .
:r 2 _.w �._ 2 � _ 3
�
, ��-_,:� , 4 �- _ __ __. , ,
; e �. ,
,
,,,
, -� � ; ^ ',
�� � 1-- -� � , :' ,
, - , _ ��� �- �
_ _
Log #3 (SRV2164-703): Mate the slot located on the bottom of Log #3 with the right log placement tab on top of Log #1.
After slot and tab have been fitted together, mate the groove located on the bottom of Log #3 with the horizontal grate bar
and slide Log#3 toward the right until it rests against the far right grate tine (see Figure 7).
Log #4 (SRV2164-704): Place Log #4 in the left log indentation on the burner top (see Figure 2). Slide Log #4 from right
to left under Log #2 to fit completely and securely into the indentation (see Figure 8). Nose of log #4 should be pulled to fit
securely against right hand side of log indentation.
�, �
�; , � �,�.' ' LOG #6 CONTA�CTS�TOP�OF=LOG#4
,.
����� _ �
, �
. , � � -=....�. - ,
�. . .. � ;;, `", -. ,�
,.
F .,4-�, '>�,„�
� "� � �� '� �� � �� �
\
�
� FLAT`i4REA� - �"� <_ <
.
.
, �-
� a' �� �^� ����-:.
���r;. ; 1 , f %. . ;,� 1
��,�� � � � � � , � ,
r=, 2 - _, 3 r;- 2 r 3
� � �j��
4 � �� 5 �� � �� 4 � 6 � 5� , . `F� ��
,, ;' . ,�";�, ,� ���
f � i , �`�:., �� ��,
j �r �
, _ . : �. ,
;�_
��- �
i � _.. .� ' _�
4 ,� yj
` .�ry � .:,, . k;.
. , LOG CONTACTS GRATE TINES
Log #5 (SRV2164-705): Place Log #5 in the right log indentation on the burner top (see Figure 2). Ensure the log fits
completely and securely in the recessed indentation (see Figure 9). Log #5 should be pulled to the left hand side of log
indentation.
Log#6 (SRV2164-706): Mate the groove located on the lower end of Log#6 with the fourth grate tine (from left to right)as
shown in Figure 10. Set the other end of Log #6 on the flat area located on top of Log #4 (see Figure 9). Log #6 will also
rest against center grate tine. When properly installed, Log #6 will rest securely on all 3 contact points, not allowing move-
ment or shifting.
2164-935C
Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12 63
G. Install the Log Assembly (continued) Log Assembly: LOGS-8C
Models: 8000C, 8000C-LP, 8000C-IPI,
8000C-IPILP, 8000CBV-IPI
FIBER BURNER TOP �OCATING HOLES � -
� � �
� ,, � -=LOG PLACEMENT INDENTATIONS
�°���/ '� ,� � �.
�8000 °vo , / TABBENTIN=NG / \
� voe o0 0 �
�°°°�������° ��°°°���� ' LOG PLACEMENT TABS
�s��000 �
� � � � �
BURNERSHIELD PILOTCOVER
BURNERASSEMBLY � �;. -
/
y / \ '—_ . �� ..
� \ Fi , . . .z\\ .
. TAB NOT BENT=LP /� \ � _ �� � �
g( I ' �i?i_,_ ���� i . _
GUIDESLEEVES � GRATE TINE
/
�
Figure 1 ' Figure 2. Log Placement Tabs
CAUTION: Logs are fragile, handle with care. Log#1 (SRV2168-701): Locate log placement tabs on the pilot cover. Bend
tabs upward as shown in Figure 2. Locate the log placements slots on the bottom of Log # 1 (see Figure 3). Mate the slots
located on the bottom of Log #1 with the log placement tabs on the pilot cover. Log # 1 is properly installed when it sits
squarely and completely on pilot cover with tabs engaged. See Figure 4.
,e �
�l,;., ,., � LOG PLACEMENT TABS
,,:_
- ,� - ,�=�
-� � � .--�,��,
-- �. � .ti�. � � �;� ��� � �
<`_ �, � ,�_
� � � ' '�,� ��'��,'�'�.
�
��
. . _
�.:_� -:..��- �-'�.,
!�_ 3,_. _ - .:��
� _ " ���
�, ;,� - ,>
LOG PLACEMENT SLOTS ' .
Figure 4 shows the log placement tabs located on the top of Log # 1. The tabs will be mated with the slots located on the
bottom of Log#2 and Log#3 (see Figure 5). Log#2 and Log#3 also have grooves that allow the logs to be seated properly
on the grate (see Figure 5). Hold Log#1 upright while placing Log#2.
Bottom view of �' '
Logs#2 and 3 , �"�
, � ,.-,
�i. 1-M _- .--- � __
4 _ _+ .'. .. ' .. qa
_ii . i ��s' `. -
LEFT GRATE TINE ' �
�; �s� ,� `, --
., �„`� SLOTS �� � �
.x��,, ��
� s� '� ?- 2 � ��„ ,, .�. _,�
t . ,�� 'Z• ��
,. 3 -.,.�.��;. --
�', GROOVES ' _ �~
� -�` -
.; q.�� _ � _
f ���
';'i ' 1 _. J .�t.o*_,`.
. .i� r.+..- �. -.w:�."."r 'rf.;- � ...� . . .. .:
V t� r°� �
�,
Log #2 (SRV2168-702): Mate the slot located on the bottom of Log #2 with the left log placement tab on top of Log #1.
After slot and tab have been fitted together, mate the groove located on the bottom of Log #2 with the horizontal grate bar
and slide Log#2 toward the left until it rests against the far left grate tine.
64 Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12
RIGHT GRATE TINE ;
°,`-�_a�:: �.��.. ��; :.
� \ 1 --.-�' ,., ������� ;P
, 1
�� 2 _ 3 2 ' 3
_
,:' ,� �,
_� � � �_ �� . �
- --- _ 4 ��
. �� M ,�1.,_ �
HORIZONTAL GRATE BAR�-"A, .� �:.,, �� � ' t,< ��
�q;.;i �,� � � .=�� � _ - = ,�, '��' -
� , � �
�,F . ,
,' ._ �. �-��, , � ,- .
_ ,
..
- .�.. � . .
� J � LOG #4 CONTACTS LOG #2
Log #3 (SRV2168-703): Mate the slot located on the bottom of Log #3 with the right log placement tab on top of Log #1.
After slot and tab have been fitted together, mate the groove located on the bottom of Log #3 with the horizontal grate bar
and far right grate tine. Log#3 will sit down on top of both the grate tine and the horizontal grate bar(see Figure 7).
Log#4(SRV2168-704): Place Log#4 in the left log indentation on the burner top(see Figure 2). Slide Log#4 from right to
left under Log#2 to fit completely and securely into the indentation (see Figure 8). The back or Log#4 should rest against
the far left grate tine as well as contact Log #2.
LOG #6 CONTACTS TOP OF LOG #4
� ��1� `
�`� � FLAT�AREA '�� � . `��'y �.` � , �' 4 -' �_��,
�,: �".� . __ ..� _
; ` ���; `
�. .,
k : _ 1 ��,
��'' 2 � 3 k 2 - 3
4 � �` -- , � � ���`�� '��� � 6 � _
5 �:: �` _ 4 5
, ,�F :
,:
��- . ,
rY.� ����- ; �� - �,
:1' _ ,- �a...rYY�,a: ,:,r:-- ,�_ ,
°� -' �LOG CONTACT,S..GRATE TINES
Log #5 (SRV2168-705): Place Log #5 in the right log indentation on the burner top (see Figure 2). Ensure the log fits
completely and securely in the indentation (see Figure 9). Log #5 should be pulled to the left hand side of log indentation.
Log #6 (SRV2168-706): Mate the groove located on the lower end of Log #6 with the fourth tine (from left to right) as
shown in Figure 10. Set the other end of Log #6 on the flat area located on top of Log #4 (see Figure 9). Log #6 will
also rest against center grate tine. When properly installed, Log #6 will rest securely on all 3 contact points, not allowing
movement or shifting.
2168-935C
Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12 65
H. Fixed Glass Assembly J. Air Shutter Setting
WARNING! Risk of Asphyxiation! Handle fixed glass Air shutter settings should be adjusted by a qualified ser-
assembly with care. Inspect the gasket to ensure it is vice technician at the time of installation.The air shutter is
undamaged and inspect the glass for cracks, chips or set at the factory for minimum vertical vent run. Adjust air
scratches. shutter for longer vertical runs. See Figure 14.5.
• DO NOT strike, slam or scratch glass. • Loosen the wing nut.
• DO NOT operate fireplace with glass removed, cracked, • Move the air handle to the left to open the air shutter.
broken or scratched.
• Move the air handle to the right to close the air shutter.
• Replace as a complete assembly.
• Tighten the wing nut.
Removing Fixed Glass Assembly
NOTICE: If sooting occurs, provide more air by opening
• Pull the four glass assembly latches out of the groove on the air shutter.
the glass frame. Remove glass door from the appliance
(see Figure 14.4).
Replacing Fixed Glass Assembly
• Replace the glass door on the appliance. Pull out and
latch the four glass assembly latches into the groove on
the glass frame. � 0
�
D
AIR SHUTTER
a � WWG NUT
t�
LATCHES
(BOTH BOTTOM
AND TOP)
Figure 14.5 Air Shutter
GLASS
ASSEMBLY
Air Shutter Settings
NG LP
6000 1/4 in. 3/4 in.
Figure 14.4 Fixed GlassAssembly 8000 1/4 in. 3/4 in.
I. Install Trim and/or Surround
• Install optional trim kits and/or surrounds using the
instructions included with the accessory.
• Use non-combustible materials to cover the gap between
the sheet rock and the appliance(when applicable to the
model).
66 Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12
15 Troubleshooting
With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service. If you do
experience a problem, this troubleshooting guide will assist a qualified service technician in the diagnosis of a problem and
the corrective action to be taken. This troubleshooting guide can only be used by a qualified service technician. Contact
your dealer to arrange a service call by a qualified service technician.
A. Standing Pilot Ignition System
Symptom Possible Causes Corrective Action
1. After repeated triggering A. No gas or low gas pressure. Check the remote shut-off valves from the appliance. Usually, there
of the red or black piezo is a valve near the gas main. There can be more than one valve be-
ignitor button, the spark tween the appliance and the main.
ignitor will not light the g. No Ip in tank. Check the LP(propane)tank.You may be out of fuel.
pilot.
C. Ignitor. Check the spark at the electrode and pilot. If no spark and electrode
wire is properly connected, replace the ignitor. Verify that there is no
short in electrode wire.
D. Pilot or misaligned electrode Using match, light the pilot. If the pilot lights, turn off the pilot and
(spark at electrode). trigger the piezo ignitor button again. If the pilot lights, an improper
gas/air mixture caused the bad lighting and a longer purge period is
recommended. If the pilot will not light, ensure the gap at the elec-
trode and pilot is one-eighth in. to have a strong spark. If the gap is
OK, replace the pilot.
2. The pilot will not stay lit A.Thermocouple. Check that the pilot flame impinges on the thermocouple.Adjust the
after carefully following pilot for proper flame impingement.
the lighting instructions. Ensure that the thermocouple connection at the gas valve is fully in-
serted and tight(hand tighten plus 1/4 turn).
Verify proper voltage output from the thermocouple to the valve.
Place one millivolt meter lead wire on the thermocouple copper lead.
Place the second lead wire on the solder button on the back of the
valve(blue wire). Start the pilot and hold the valve knob in. The mil-
livolt reading should read 8-16 millivolts. If millivolt reading is less
than 8 millivolts, replace thermocouple.
B. Improper gas inlet pressure. Natural gas should be 5-10 in.w.c. LP should be 11-13 in.w.c. Verify
pressure with manometer.
C. Valve. If the thermocouple is producing 8-16 millivolts, replace control valve.
3. The pilot is burning, A. ON/OFF switch or wires. Check the ON/OFF switch and wires for proper connections. Place
there is no burner the jumper wires across the terminals at the ON/OFF switch. If the
flame, the valve knob is burner comes on, replace the ON/OFF switch. If the ON/OFF switch
in the ON position, and is OK, place the jumper wires across the ON/OFF switch wires at the
the ON/OFF switch is in gas valve. If the burner comes on,the wires are faulty or connections
the ON position. are bad.
B.Thermopile may not be gen- Check that the pilot flame impinges thermopile properly.
erating sufficient millivoltage. ge sure the wire connections from the thermopile at the gas valve
terminals are tight and that the thermopile is fully inserted into the
pilot bracket.
Check the thermopile with a millivolt meter. Take the reading at TH-
TP&TP terminals of the gas valve. The meter should read 350 mil-
livolts minimum, while holding the valve knob depressed in the pilot
position,with the pilot lit, and the ON/OFF switch in the OFF position.
Replace the thermopile if the reading is below the specified mini-
mum.
With the pilot in the ON position, disconnect the thermopile leads
from the valve. Take a reading at the thermopile leads. The reading
should be 350 millivolts minimum. Replace the thermopile if the read-
ing is below the minimum.
Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12 67
Troubleshooting (continued)
Symptom Possible Cause Corrective Action
3. (Continued) C. Valve. Turn the valve knob to the ON position. Place the ON/
OFF switch in the ON position. Take a reading with a
millivolt meter at the thermopile terminals.The millivolt
meter should read greater than 125mV. If the reading
is acceptable, and if the burner does not come on, re-
place the gas valve.
D. Plugged burner orifice. Check the burner orifice for stoppage. Remove stop-
page.
E.Wall switch or wires. Check the wall switch and wires for proper connec-
tions. Place the jumper wires across the terminals at
the wall switch. If the burner comes on, replace the
wall switch. If the wall switch is OK, place the jumper
wires across the wall switch wires at the gas valve. If
the burner comes on, the wires are faulty or connec-
tions are bad.
4. Frequent pilot outage A. Pilot flame may be too high or too low, or blow- Clean thermocouple and adjust the pilot flame for
problem. ing out(high pressure), causing pilot safety to proper flame impingement. Follow lighting instructions
drop out. carefully.
5.The pilot and main A. No LP in tank. Check the LP(propane)tank. Refill the fuel tank.
burner extinguish
while in operation. B• Improper gas inlet pressure. Natural gas should be 5-10 in.w.c. LP should be 11-13
in.w.c. Verify pressure with manometer.
C. Inner vent pipe leaking exhaust gases back Check venting system for damage. Replace/repair im-
into the system. properly assembled pipe sections.
D. Glass installed improperly. Check to ensure glass is installed properly. Replace
fixed glass panel assembly.
E.Thermopile or thermocouple. Replace pilot if necessary.
F. Improper vent cap installation. Check for proper installation and freedom from debris
orblockage.
6. Glass soots. A. Flame impingement. Adjust the log set so that the flame does not exces-
sively impinge on it. Refer to log instructions.
B. Improper air shutter setting. Refer to manual for shutter set points. Ensure that set
point is correct for appliance/gas type. If unit has ad-
justable shutter, it may be necessary to increase shut-
ter opening.
C. Debris around air shutter. Inspect the opening at the base of the burner. NO MA-
TERIAL SHOULD BE PLACED IN THIS OPENING.
7. Flame burns blue A. Insufficient oxygen being supplied. Ensure that the vent cap is installed properly and free
and lifts off burner. of debris. Ensure that the vent system joints are tight
and have no leaks.
Ensure that no debris has been placed at the base of,
or in the area of the air holes in the center of the base
pan beneath the burner.
Ensure that the glass is tightened properly on the unit,
particularly on top corners.
68 Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12
B. IntelliFire PIusT"" Ignition System
Symptom Possible Cause Corrective Action
1. Pilot won't light. A. Incorrect wiring. Verify"S"wire (white)for sensor and"I"wire (orange)for ignitor are
The ignitor/module connected to correct terminals on module and pilot assembly.
makes noise, but no
spark. B. Loose connections or electrical Verify no loose connections or electrical shorts in wiring from mod-
shorts in the wiring. ule to pilot assembly.Verify connections underneath pilot assembly
are tight;also verify igniter and flame sense wires are not grounding
out to metal chassis, pilot burner, pilot enclosure, mesh screen if
present, or any other metal object.
C. Ignitor gap is too large. Verify gap of igniter to right side of pilot hood. The gap should be
approximately.17 in. or 1/8 in. (3 mm).
2. Pilot won't light, A. No power,transformer installed Verify that transformer is installed and plugged into module. Check
there is no noise or incorrectly, or depleted batteries. voltage of transformer at connection to module. Acceptable read-
spark. ings of a good transformer are between 6.4 and 6.6 volts AC. Bat-
tery power supply voltage must be at least 4 volts. If below 4 volts,
replace batteries.
B. A shorted or loose connection in Remove and reinstall the wiring harness that plugs into module.
wiring configuration or wiring har- Verify there is a tight fit. Verify pilot assembly wiring to module. Re-
ness. move and verify continuity of each wire in wiring harness. Replace
any damaged components.
C. Improper wall switch wiring. Verify that 110/VAC power is"ON"to junction box.
D. Module not grounded. Verify black ground wire from module wire harness is grounded to
metal chassis of appliance.
3. Pilot sparks, but A. Gas supply. Verify that incoming gas line ball valve is "open". Verify that inlet
Pilot will not light. pressure reading is within acceptable limits.
B. Ignitor gap is too large. Verify gap of igniter to right side of pilot hood. The gap should be
approximately.17 in. or 1/8 in. (3 mm).
C. Module is not grounded. Verify module is securely grounded to metal chassis of appliance.
D. Pilot valve solenoid Verify that 1.5 to 1.8 VDC is supplied to pilot solenoid from module.
If below 1.5 volts, replace module. If 1.5 volts or greater, replace
valve.
4. Pilot lights but con- A. A shorted or loose connection in Verify all connections to wiring diagram in manual. Verify connec-
tinues to spark, and flame sensing rod. tions underneath pilot assembly are tight. Verify flame sense or ig-
main burner will not niter wires are not grounding out to metal chassis, pilot burner, pilot
ignite. (If the pilot enclosure or screen if present, or any other metal object.
continues to spark
after the pilot flame B• Poor flame rectification or contami- With fixed glass assembly in place, verify that flame is engulfing
has been lit,flame nated flame sensing rod. flame sensing rod on left side of pilot hood. Flame sensing rod
rectification has not should glow shortly after ignition. With a multi-meter, verify that
occurred.) current in series between module and sense lead is at least 0.14
microamps.Verify correct pilot orifice is installed and gas inlet is set
to pressure specifications. Polish flame sensing rod with fine steel
wool to remove any contaminants that may have accumulated on
flame sensing rod.
C. Module is not grounded. Verify module is securely grounded to metal chassis of appliance.
Verify that wire harness is firmly connected to the module.
D. Damaged pilot assembly or con- Verify that ceramic insulator around the flame sensing rod is not
taminated flame sensing rod. cracked, damaged, or loose. Verify connection from flame sensing
rod to white sensor wire. Polish flame sensing rod with fine steel
wool to remove any contaminants that may have accumulated on
flame sensing rod.Verify continuity with a multi-meter with ohms set
at lowest range. Replace pilot if any damage is detected.
Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12 69
16 Reference Materials
A. Appliance Dimension Diagram
Dimensions are actual appliance dimensions. Use for reference only. For framing dimensions and clearances refer to Section 5.
L -
�M—>
� ' � J
K
N �
TOP VIEW
00 UO -- 00 00
0 0
GAS LINE H
ACCESS
R �
C �
G
O
(� E
• � .' � � . � 0 '. °. I � �•
<—P�� � .E A � � `—F—'
LEFT SIDE FRONT VIEW RIGHT SIDE
Location Inches Millimeters Location Inches Millimeters
A 41 1041 J 21 533
B 36-1/8 918 K 11-11/16 297
C 33-1/2 851 L 28-1/2 724
D 34-5/8 879 M 14-1/4 362
E 2-1/4 57 N 8-1/2 216
F 9-11/16 246 O 2-7/8 73
G 26-7/8 683 P 8-1/2 216
H 6 dia 152 Q 1 25
I 39-7/8 1013 R 40-7/8 1038
Figure 16.1 Appliance Dimensions-6000 Models
70 Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12
•E L -
.E M—;
� �
N K
�
TOP VIEW
00 00 --- �0 U�
O O H
, GAS LINE
ACCESS R
I
. C � .
G
. p Q E
•� � � �Y �• � 0 , � � � �,
�P—.� � 'E B
� �F—>
E A �
LEFT SIDE FRONT VIEW RIGHT VIEW
Location Inches Millimeters Location Inches Millimeters
A 48 1219 J 21 533
B 43-1/8 1096 K 11-11/16 297
C 35-1/2 902 L 35-1/2 902
D 36-5/8 930 M 17-3/4 451
E 2-3/8 60 N 8-1/2 216
F 9-15/16 252 O 2-7/8 73
G 28-7/8 734 P 8-1/2 216
H 6 152 Q 1 25
I 41-7/8 1064 R 42-7/8 1089
Figure 16.2 Appliance Dimensions-8000 Models
Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12 71
B. Vent Components Diagrams
�
Pipe
Effective Length
Inches Millimeters 10-1/2 in.
Effective DVP4 4 102 (267 mm) 45�
HeighULength
DVP6 6 152
� DVP12 12 305 0
4-7/8 in. ° °
DVP24 24 610 (124 mm)
� � DVP36 36 914 �—10-7/8 in.
DVP Pipe(see chart)
DVP48 48 1219 (276 mm)
DVP6A 3 to 6 76 to 152 DVP45(45°Elbow)
DVP12A 3 to 12 76 to 305
11-3/8 in.
(289 mm)
� 10 in. 1 in.
(254 mm) (25 mm) �
� 7-3/8 in.
(187 mm)
10 in. ° 7-1/4 in.(32 mm)
(254 mm) �`
�9-1/4 in.
AsSembled (235 mm) 1/2 in. TYP
Height:24 in./610 mm 13-1/4 in. (�3 mm)
Diameter: 10 in./254 mm — (337 mm)
DVP-AS2 DVP-FS(Ceiling Firestop) DVP90ST(90°Elbow)
12 in. 1 in.
�� (305 mm) � � ~(25 mm)
i i �
i i
i i
� 8 in.
0 10 in. 0 1-1/2 in. i + i + II (203 mm)
�(254 mm)—� �I � (38 mm) i i ' �
14 in. i i '
(356 mm) i i !
UP * i -----i----- i
� � i '
i i I
5 in. 12 in. � i �
(127 mm) (305 mm) � � '
� 6in. �
(152 mm)
DVP-HVS(Vent Support) DVP-WS(Wall Shield Firestop)
Figure 16.3 DVP vent components
72 Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12
B. Vent Components Diagrams (continuea�
Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm). The heat shield is designed to be
used on a wall 4 in.to 7-1/4 in. (102 mm to 184 mm)thick. If wall thickness is less than 4 in. (102 mm)the
existing heat shields must be field trimmed. If wall thickness is greater than 7-1/4 in. (184 mm)a DVP-HSM-B
will be required.
� 8 in.
(203 mm) I Heat
Shield
� �0�00� ����
, . . . . , . .D0000 .���
15-1/8 in. Q
(384 mm) �..O�T -0
. . —
I Term Cap Minimum Maximum
�--�� Effective Length Effective Length
I- 12 In. -I Max 3-1/8 in. 4-5/8 in.
(305 mm) Effective Trap1
Length 79 mm 117 mm
DVP-TRAP 5-3/8 in. 9-3/8 in.
Horizontal Termination Cap Trap2
137 mm 238 mm
o �B� �0���� �e� ������
�B. ��0��. �B. 000��.
DVP-TRAP1 DVP-TRAP2
�8� ������ �B� �U�00�
�8. �0���. �B. ��0�.
DVP-TRAPK1 DVP-TRAPK2
a
DVP-HPC1 DVP-HPC2
Figure 16.4 DVP vent components
Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12 73
B. Vent Components Diagrams (continuea�
� 31 in.. _
(787 mm)
13-1/4 in. �
(337 mm) 24-5/8 in.
(625 mm)
� �
24-5/8 in. 27-1/2 in. —
(625 mm) \, / �(699 mm) �
'Y � 13-1/4 in.
337 mm)
RF6M RF12M
Roof Flashing Multi-pak
Roof Flashing Multi-pak
13-3/4 in. 5�n' 11-7/8 in. 5 in.�
� (349 mm)� ��127 mm)� �(302 mm)� (127 mm)
13-3/4 in. 13-7/8 in.
(349 mm) (352 mm)
BEK DVP-BEK2
Trap Cap Brick Extension DVP-HPC Cap Brick Extension
11-5/8 in. 000�� 00
' \ (295 mm)�
����� �� pao� o0
12-1/8 in. �(�� �
. 7-1/8 in. (308 mm) lJll�
(181 ml m) Q(� �
i ����� �� Illl
L ,
DVP-TRAPFL r 5-3/4
(146 mm) COOL-ADDM
Flashing
Cap Shield
13-7/8 in. 9-1/2 in.
,E 26 in. � (352 mm) I(241 mm)I
660 mm ��
- �o0 00
14 in.
DVP-HSM-B (356 mm)
Extended Heat Shield
00 00
DRC-RADIUS
Figure 16.5 DVP vent components Cap Shield
74 Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12
B. Vent Components Diagrams (continuea�
7-3/8 in.
(187 mm) .
1-1/2 in. .
(38 mm)
� ��;
o �
8 �
0
17-3/4 in.
14 in. (451 mm)
(356 mm)
LINK-DV-306
(LINK-DV-30)
12 in.
(305 mm)
12 in.
DVP-TB1 I.e 305 mm -I
BasementVent Cap T -
T
7-1/4 in. �
(184 mm) '
12-1/2 in.
� (318 mm)
• 5-1/4 in.
�. (133 mm) � �
a �
DVP-NHW
PVK-80 VerticalTermination Cap(Highwind)
(Not compatible with Intellifire PIusT"")
(For use with IPI and DSI appliances only.)
' . � —> 7-1/4 in. �
16-7/8 in. 14 in. 1 in. (184 mm)
HOT (429 mm) . (356 mm) (25 mm)�
�
� 12 in. � o
(305 mm) 14 in.
(356 mm) o
7-1/8 in.
12-118 in. (181 mm)
(314 mm)
3/8 in. (10 mm) �
8-3/4 in. �
(222 mm) 1 in. (25 mm)
7-3/4 to 10-3/8 in.
1-5/8 in. (197 to 264 mm)
(41 mm)
DVP-FBHT
DVP High Performance Cap FireBrickTermination Cap
Figure 16.6 DVP vent components
Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12 75
��s-sia�n. Optional Wire Harness
sasm� DESCRIPTION PART NUMBER
� � 10 ft. PV Wire Harness PVI-WH10
• ;� 20 ft. PV Wire Harness PVI-WH2O
� 40 ft. PV Wire Harness PVI-WH40
° �z-�i2'°. 60 ft. PV Wire Harness PVI-WH60
• 318 mm
' . � 80 ft. PV Wire Harness PVI-WH80
� 100 ft. PV Wire Harness PVI-WH100
�
20-314 in.
�527 mm
Note: Wire harnesses required to power the PVI-SLP
connect to the appliance and are ordered separately
PVI-SLP from PVI-SLP. Contact your dealer to order.
Power Vent Inline
16 in.
c 406 mm—>
15 in.
4-1/2 in. E (381 mm) -
—>114mmF
- 93/16 in.
�(233 mm)�
. ���\ . �
� 13-S18 in. 16-11116 in. 16•11116 in.
(346 mm) 424 mm (424 mm)
0 12-1/2 in. o �
�—(318 mm)—�
SLP-LPC
SLP Low Profile Cap
76 Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12
B. Vent Components Diagrams (continued)
8-1/8 in. 13 in.
(206 mm) (330 mm) Effective Length
I,F �, I,E �,I 5-3/4 to 8-3/8 in. 5-1/2 in. 8-3/8 in.
146 to 213 mm 140 mm 213 mm
� 87° 301�— .
15 in. �
(381 mm) � 10-1/2 in. �
267 mm O
I 10-7/8 in.
� � 2�mm ,. .,
A WARNING
Fire Risk.
• When using DVP-HRC-SS and DVP-HRC-ZC-
SS termination caps on top vented fireplaces,a
6 inch minimum vertical vent section is required
before installing first elbow.
DVP-HRC-SS
DVP-HRC-ZC-SS
HORIZONTAL TERMINATION CAP
COAXIAL to COLINEAR VENTING
LI N K-DV30B 768-380A DV-46DVA-GC L
Flex Liner Kit Stainless Steel Flex Pipe Coaxial/ColinearAppliance Connector
/
DVP-2SL
Adapter
Figure 16.7 DVP vent components
Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12 77
B. Vent Components Diagrams (continued)
�6-1/2 in.�
165 mm
�6-1/2 in. �
� 165 mm
� � 6-1/2 in.
8-3/4 in. '� 165 mm
222 mm I 9-1/4 in.
� 6 in. �' 235 mm
152�mm �
6-5/�g in I
168 mm �
SLP45 F6-5/8 in.�
45° Elbow 168 mm
�_9-7/8 in. _
251 mm
� SLP90
90° Elbow
Effective
6-1/2 in.
HeighU � <--165 mm
Length
� Effective Height/Length
Pipe inches mm
SLP4 4 102
SLP PIPE SLP6 6 152
SLP12 12 305 25-3/16 in.
SLP24 24 610 640 mm
T SLP36 36 914
SLP48 48 1219
10-7/8 in. SLP6A 2-6 51 -152
276 mm SLP12A 2-12 51 -305 e
�. - .E 8-1/16 in.
205 mm
� 8-7/8 in. � � �1-1/2 in.
225 mm 38 mm DVP-SLP24
Adapter
SLP-HVS
Horizontal Pipe
Support
_ �
8 11/16 in. � 12 in.
220 mm 305 mm
.... �
0 8-11/16 in. a <-1-1/2 in. 12 in. 1�146 mIm
�220 mm� � 38 mm �305 mm
SLP-FS SLP-WS
Ceiling Firestop Wall Shield Firestop
Figure 16.8 SLP Series Vent Components
78 Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12
B. Vent Components Diagrams (continued)
Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm).The heat shield is designed to be
used on a wall 4 in.to 7-1/4 in. (102 mm to 184 mm)thick. If wall thickness is less than 4 in. (102 mm)
the existing heat shields must be field trimmed. If wall thickness is greater than 7-1/4 in. (184 mm)a
DVP-HSM-B will be required.
. 8 in. -
(203 mm)
Heat
Shield
15-1/8 in. . . �° M°�' �������0
(384 mm) ��� �Q��y��.
. . Minimum Maximum
�d Term Cap Effective Length Effective Length
MaX 3-1/8 in. 4-3/4 in.
.E 12 111. � EffeCtive Trap1 �g mm 121 mm
(305 mm) Length
5-1/4 in. 9-1/4 in.
SLP-TRAP Trap2
Horizontal Termination Cap 133 mm 235 mm
6-3/8 in. 4-3/16 in.
163 mm �� ��106 mm
4 in 4-5% in.
102 mm 117 mm
� - - y
8-1/8 in. I' 5-1/16 in.
�206 mm� � 1�128 mm
DVP-2SL
Adapter
T
14-7/16 in.
367 mm
,E 26 in. _ �
660 mm
� 14-7/16 in� E—591mm
367 mm
DVP-HSM-B
Extended Heat Shield SLP-WT-BK
Wall Thimble-Black
Figure 16.9 SLP Series Vent Components
Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12 79
B. Vent Components Diagrams (continued)
T �
14 in. 13 in.
356 mm 330 mm
� � 1-5/16 in.
�10-9/16 in. ,F 13 in.� _, I�34 mm
269 mm � 330 mm
SLP-CCS-BK SLP-DCF-BK
Cathedral Ceiling Ceiling Firestop
Support Box-Black Black
10-11/16 in.
� �F
. �.� .
271 mm
� 0 4, o � � � E 12in.�
HOT • 305 mm
� ° ° � �� �
28-1/2 in. °°
724 mm ��
12-1/2 in.
318 mm
_ �
13-1/2 in�
` 343 mm SLP-TVHW
Vertical
SLK-SNKD Termination Cap
Snorkel
Termination Cap
Figure 16.10 SLP Series Vent Components
80 Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12
c. ser�ice Parts 6000C, 6000C-IPI
HEAT GLO.
Beginning Manufacturing Date:Aug 2009
36" Gas Fireplace - DV Endin Manufacturin Date:Active
No one builds a better fire g g
Log Set Assembly 7�
� � �,,
rx
��:'°w.° . `.,l`�'r:..
�
`t$��'�2 1 � ' '' $ ' 0
� � 4 s 5 3 ' �
;::� * 0
{'i
, , � 9
10 �►,.
14 13 � 91—>� ... Io.
15 •al
� � 11
12\�` • '�16
y ��9ez..
IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement
parts for your appliance please provide model number and serial number.All parts listed StOCked
in this manual may be ordered from an authorized dealer. at DepOt
ITEM DESCRIPTION COMMENTS PART NUMBER
Log Set Assembly LOGS-6C Y
1 Log 1 SRV2164-701
2 Log 2 SRV2164-702
3 Log 3 SRV2164-703
4 Log 4 SRV2164-704
5 Log 5 SRV2164-705
6 Log 6 SRV2164-706
7 Insulation Board 2166-136
8 Burner Top SRV2166-100 Y
Burner NG 2164-007 Y
9
Burner LP 2164-008 Y
9.1 Air Scoop 2170-188
9.2 Pilot Cover 2170-181
10 Log Grate 2166-104
11 Base Refractory SRV6BASE-STRAT
12 Refractory Basket 2166-108
13 Glass Door Assembly GLA-6000G Y
14 Surround Assembly 2166-019
15 Finishing Strips (Sold as kit only) SRVFS-6
16 Junction Box 4021-013 Y
Additional service part numbers appear on following page. 9/12
Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12 81
H EAT� G LO Service Parts $QQQC, $QQQC-�P�
42" Gas Fireplace - DV Beginning Manufacturing Date:Aug 2009
No one builds a better fire Ending Manufacturing Date:Active
Log Set Assembly ��
q;
,;:;� • o
,�Z + � 3 8
A 4 6�� � '` � O
- _ . < 14 ,• 9 .
13 10 �- s.�. _...__ I
0'
15 � .�.ol
\ � 11 � a
y 12 � � ,
� �16
��9.2 :
IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement
parts for your appliance please provide model number and serial number.All parts listed StOCked
in this manual may be ordered from an authorized dealer. at DepOt
ITEM DESCRIPTION COMMENTS PART NUMBER
Log Set Assembly LOGS-8C Y
1 Log 1 SRV2168-701
2 Log 2 SRV2168-702
3 Log 3 SRV2168-703
4 Log 4 SRV2168-704
5 Log 5 SRV2168-705
6 Log 6 SRV2168-706
7 Insulation Board 2170-136
8 Burner Top SRV2170-100 Y
Burner NG 2168-007 Y
9
Burner LP 2168-008 Y
9.1 Air Scoop 2170-188
9.2 Pilot Cover 2170-181
10 Log Grate 2170-104
11 Base Refractory SRV8BASE-STRAT
12 Refractory Basket 2170-108
13 Glass DoorAssembly GLA-950TR Y
14 Surround Assembly 2170-019
15 Finishing Strips (Sold as kit only) SRVFS-8
16 Junction Box 4021-013 Y
Additional service part numbers appear on following page. 9/12
82 Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12
service Parts 6000C-IPI, 8000C-IPI
HEAT GLO..
Beginning Manufacturing Date:Aug 2009
No one builds a better fire Ending Manufacturing Date:Active
#17 Valve Assembly 17�2 �
17.1 �/
• � �
17.3 � O 17.14
'� 17.15 R
o \
/
. 17.13
� 17.12
17.4 � � �
.o � �
e. ? � 17.11
mo I
� 17.7 � 17.10
� �
17.6 � 17.9
17.5 �
17.8
IMPORTANT:THIS IS DATED INFORMATION. When requesting service or replacement
parts for your appliance please provide model number and serial number.All parts listed StOCked
in this manual may be ordered from an authorized dealer. at DepOt
ITEM DESCRIPTION COMMENTS PART NUMBER
17.1 Shutter Bracket Assembly 2166-157 Y
Pilot Assembly NG 2166-370 Y
17.2
Pilot Assembly LP 2166-371 Y
Pilot Tube SRV485-301 Y
17.3 3-hole Grommet 2118-420
17.4 Valve Bracket 2118-104
17.5 Flex Ball Valve Assembly 302-320A Y
Valve NG 2166-302 Y
17.6
Valve LP 2166-303 Y
17.7 Male Connector Pkg of 5 303-315/5 Y
17.8 Bulkhead W/Tube 2166-119 Y
17.9 Jumper Wire 2187-198 Y
17.10 Battery Pack** 2166-323 Y
17.11 Thermostat Wire Assembly 2118-170 Y
17.12 Transformer 2166-305 Y
17.13 Control Assembly 2164-030 Y
17.14 Module 2166-307 Y
17.15 Wire Harness 2166-304 Y
Burner Orifice NG (#37C) 582-837 Y
Burner Orifice LP (#52C) 6000C-IPI 582-852 Y
Burner Orifice NG (#33C) 582-833 Y
Burner Orifice LP (#50C) 8000C-IPI 582-850 Y
*�Fuse for battery pack can be sourced locally, not a warranty item. Specs are 500mA-10A 3/4"long
Additional service part numbers appear on following page.
Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12 83
ser�ice Parts 6000C, 8000C
HEAT GLO..
Beginning Manufacturing Date:Aug 2009
No one builds a better fire Ending Manufacturing Date: Jan 2010
#17 Valve Assembly ���
17.2 � �
17.3 `i �
O��
17.4 � �
.�
17.5\ � �
�y � � � 17.10
��, 17.6 �
� 17.8 �17.9
�
17.7
IMPORTANT:THIS IS DATED INFORMATION. When requesting service or replacement
parts for your appliance please provide model number and serial number.All parts listed StoCked
in this manual may be ordered from an authorized dealer. at Depot
ITEM DESCRIPTION COMMENTS PART NUMBER
17.1 Shutter Bracket Assembly 2166-157 Y
Pilot Assembly NG 2103-010 Y
17.2
Pilot Assembly LP 2103-011 Y
Pilot Tube SRV485-301 Y
Thermopile 2103-512 Y
Thermocouple 446-511 Y
17.3 3-hole Grommet 2118-420
17.4 Valve Bracket 2118-104
17.5 Flex Ball Valve Assembly 302-320A Y
17.6 Piezo Ignitor 291-513 Y
Valve NG 2166-300 Y
17.7
Valve LP 2166-301 Y
17.8 Male Connector Pkg of 5 303-315/5 Y
17.9 Bulkhead W/Tube 2166-119 Y
17.10 Thermostat Wire Assembly 2045-024 Y
Burner Orifice NG (#37C) 582-837 Y
6000C
Burner Orifice LP (#52C) 582-852 Y
Burner Orifice NG (#33C) $OOOC 582-833 Y
Burner Orifice LP (#50C) 582-850 Y
Wire Assembly 040-557A
Additional service part numbers appear on following page.
84 Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12
H E AT� G LO M Service Parts 600QC, $QQQC
Beginning Manufacturing Date:Aug 2009
No one builds a better fire Ending Manufacturing Date:Active
IMPORTANT:THIS IS DATED INFORMATION. When requesting service or replacement
parts for your appliance please provide model number and serial number.All parts listed StOCked
in this manual may be ordered from an authorized dealer. at DepOt
ITEM DESCRIPTION COMMENTS PART NUMBER
Exhaust Shield 385-105
Flue Restrictor 385-128
Gasket Assembly
2166-081
Contains Vent, Burner Neck,Valve Plate, LED and Adjustable Air Shutter Gaskets
Glass Latch Support Pkg of 2 33858/2 Y
Mineral Wool 050-721
Touch Up Paint TUP-GBK-12
Standing Pilot Conversion Kits
Conversion Kit NG NGKS-6C Y
6000C
Conversion Kit LP LPKS-6C Y
Conversion Kit NG NGKS-8C Y
8000C
Conversion Kit LP LPKS-8C Y
Regulator NG NGK-SITV-50 Y
Regulator LP LPK-SITV-50 Y
Pilot Orifice NG 2103-116 Y
Pilot Orifice LP 2103-117 Y
IPI Conversion Kits
Conversion Kit NG NGKI-6C Y
6000C-IPI
Conversion Kit LP LPKI-6C Y
Conversion Kit NG NGKI-8C Y
8000C-IPI
Conversion Kit LP LPKI-8C Y
Regulator NG NGK-DXV-50 Y
Regulator LP LPK-DXV-50 Y
Pilot Orifice NG 593-528 Y
Pilot Orifice LP 593-527 Y
Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12 85
D. Contact Information
HEAT�GLO.
No one builds a better fire
Heat&Glo, a brand of Hearth & Home Technologies Inc.
7571 215�h Street West, Lakeville, MN 55044
www.heatnglo.com
Please contact your Heat & Glo dealer with any questions or concerns.
For the location of your nearest Heat & Glo dealer,
please visit www.heatnglo.com.
- NOTES -
NOTICE
� DO NOT DISCARD THIS MANUAL
� • Important operating • Read,understand and follow • Leave this manual with
and maintenance these instructions for safe party responsible for use
instructions included. installation and operation. and operation.
This product may be covered by one or more of the following patents: (United States) 5328356, 5601073, 5613487,
5647340, 5890485, 5941237, 5947112, 5996575, 6006743, 6019099, 6053165, 6145502, 6170481, 6374822, 6484712,
6601579, 6769426, 6863064, 7077122, 7098269, 7258116, 7470729 or other U.S. and foreign patents pending.
2000-945
Printed in U.S.A.- Copyright 2012
86 Heat&Glo • 6000C,6000C-IPI,8000C,8000C-IPI • 2164-900 Rev.T • 9/12