HomeMy WebLinkAboutB13-0496 REV1 TRANSMITTAL INSTALLATION INSTRUCTIONS Y Department of Community Development
0 75 South Frontage Road
TOWN OF VAIL ` Vail, GO 81657
Tel: 970.479.2128
www.vailgov.com
Development Review Coordinator
TRANSMITTAL FORM
Use this form when submitting additional information for planning applications or building permits.
This form is also used for requesting a revision to building permits. A two hour minimum building review
fee of$110 will be charged upon reissuance of the permit.
Application/Permit#(s) information applies
to: Attention: ("(Revisions
�� 2 Q ( ) Response to Correction Letter
J r2 �V S _attached copy of correction letter
1 Y10 L) S 3LL 6 O Deferred Submittal
( )
Oth
Project Street Address:
(Number) (Street) / �, �� (S Ite#)
Building/Complex Name: ��(/fir Description of Transmittal/List of Changes, Items Attached:
Applicant Information
F
(architect, contractor, owner/owner's rep)
Contact Nam Q �C-
s
Address:
City State: Zip:
Contact Name: ,rj 2 (use additional sheet if necessary)
Contact Phone: O�LO Building Permits:
Contact E-Mail:l�!/ i(�(// (�,�� e/ �(/ Revised ADDITIONAL Valuations (Labor& Materials)
(DO NOT include original valuation)
�a/l Co A4-
I hereby acknowledge that I have read Is a lication,filled out Building: $
in full the information required,completed an accurate plot plan,
and state that all the information as required is correct. I agree to Plumbing: $
comply with the information and plot plan,to comply with all Town
ordinances and state laws, and to build this structure according Electrical: $
to the town's z in and subdivision codes, design review ap-
prove , Int t I Building and Residential Codes and other Mechanical: $
ordin e own applicable thereto.
X Total: $ 2. �;_00
Own r/ R presentative Signature (Required)
Date Received:
For Office Use Only:
Fee Paid: NOV 212013
Received From:
Cash Check#
CC: Visa/MC Last 4 CC# exp. date: TOWN OF VAIL
Authorization #
I
Installation Washer
Instructions WCVH4800 and WCVH4815
if you have any questions, call 800.GE.CARES (800.432.2737) or visit our Website at:
GEAppliances.com
in Canada, call 1.800.561.3344 or visit www.GEAppliances.ca
BEFORE YOU BEGIN TOOLS REQUIRED FOR
Read these instructions completely and carefully. WASHER INSTALLATION
❑Wrench(provided)
• IMPORTANT — save these instructions
for local inspector's use. ❑ Channel-lock adjustable pliers
• IMPORTANT — Observe all governing ❑ Carpenter's level
codes and ordinances.
• Note to Installer-Be sure to leave these
instructions with the Consumer.
PARTS SUPPLIED
• Note to Consumer-Keep these instructions
for future reference.
• Skill level-Installation of this appliance requires U
basic mechanical and electrical skills. ■ Wrench
• Completion time- 1-3 hours
• Proper installation is the responsibility of the installer.
• Product failure due to improper installation is not
covered under the Warranty. ■ Water Hoses(2)
FOR YOUR SAFETY: ■ Hose Guide
A WA R N I N G ■ Hose Fittings(4)
• This appliance must be properly grounded and
installed as described in these Installation Instructions.
• Do not install or store appliance in an area where
it will be exposed to water/weather.See Location ■ Shipping Bolt
of Your Washer section. pp g
Hole Covers(4)
• NOTE:This appliance must be properly ■ Detergent Cup
grounded,and electrical service to the washer
must conform with local codes and ordinances
and the latest edition of the National Electrical
Code,ANSI/NFPA 70.
13
i
Installation Instructions
LOCATION OF YOUR WASHER ROUGH-IN DIMENSIONS
Do Not Install the Washer: FRONT
1.In an area exposed to dripping water or outside 23.5"
weather conditions.The ambient temperature (597 mm)
should never be below 60°F(15.6°C)for proper
washer operation. �,,�
2.In an area where it will come in contact with curtains ��o 0
or drapes. o 0 0 ° 0
3.On carpet.The floor MUST be a hard surface with
a maximum slope of 112"per foot(1.27 cm per
30 cm).To make sure the washer does not vibrate
or move,you may have to reinforce the floor. 33.4"*
NOTE:If floor is in poor condition,use 3/4"impregnated (849 mm)
plywood sheet solidly attached to existing floor covering.
IMPORTANT:
Minimum Installation Clearances
• When installed in alcove:Sides,Rear,
Top=0"(0 cm)
i
• When installed in closet:Sides,Rear,
Top=0"(0 cm),Front= 1"(2.54 cm)
• Closet door ventilation openings required: SIDE
2 louvers each 60 square in.(387 CM2),located 3
(7.6 cm)from top and bottom of door 26.6"
(676.5 mm)
CONTRACTOR DIMENSIONS
BACK
i
1533 mm) 6.25" j
(159 mm)
i
i
4 33.4"*
(102 mm) (849 mm)
I
29.75"
(756 mm)
*NOTE:
washer legs have 0.75"(19 mm)adjustability.
27.75" Stacked:67.7"(171.8 cm)
(705 mm)
i
14
i
Installation Instructions
UNPACKING THE WASHER UNPACKING THE WASHER (cont.)
AWARNING: Recycle or destroy the carton 7. Insert shipping bolt hole covers into shipping bolt holes.
and plastic bags after the washer is unpacked.Make
materials inaccessible to children.Children might use - —
them for play.Cartons covered with rugs,bedspreads
or plastic sheets can become airtight chambers causing
suffocation.
1. Cut and remove all packaging straps.
2. While it is in the carton,carefully lay the washer on its
side.DO NOT lay the washer on its front or back. o
3. Turn down the bottom flaps.Remove all base packaging I�
including the styrofoam base. o
4. Carefully return the washer to an upright position and 0 o
remove the carton by lifting it upward.
5. Carefully move the washer to within 4 feet(122cm) NOTES:
of the final location. •Failure to remove the shipping braces can cause
the washer to become severely unbalanced.
6. Remove the following from the back side of the washer.
4 bolts .Save all bolts for future use.
4 plastic spacers(including rubber grommets) •If you must transport the washer at a later date,you must
reinstall the shipping support hardware to prevent shipping
Do not remove damage.Keep the hardware in the plastic bag provided.
screw or clip
0
15
i
Installation Instructions
ELECTRICAL REQUIREMENTS WATER SUPPLY REQUIREMENTS
Read these instructions completely Hot and cold water faucets MUST be installed within
and carefully. 42 inches(107 cm)of your washer's water inlet.The faucets
MUST be 3/4"(1.9 cm)garden hose-type so inlet hoses
can be connected.Water pressure MUST be between 10
AWAR N I N G—TO REDUCE THE RISK OF and 120 pounds per square inch.Your water department
FIRE,ELECTRICAL SHOCK AND PERSONAL INJURY: can advise you of your water pressure.The hot water
• DO NOT USE AN EXTENSION CORD OR AN ADAPTER temperature should be set to deliver water at 120°to 140°F
PLUG WITH THIS APPLIANCE. (48°-60°C)
Washer must be electrically grounded in accordance to provide proper Automatic Temperature Control(ATC)
with local codes and ordinances or,in the absence performance.
of local codes,in accordance with the NATIONAL
ELECTRICAL CODE,ANSI/NFPA NO.70.
DRAIN REQUIREMENTS
CIRCUIT-Individual,properly polarized and grounded 1. Drain capable of eliminating 9.5 gals(36 L)per minute.
15-amp branch circuit fused with 15-amp,time-delay fuse
or circuit breaker. 2. A standpipe diameter of 1-1/4"(3.18 cm)minimum.
POWER SUPPLY-2-wire,with ground,120-volt, 3. The standpipe height above the floor should be:
single-phase,60-Hz,Alternating Current. Minimum height:30"(76 cm)
OUTLET RECEPTACLE-Properly
Maximum
grounded 3-prong receptacle to be I�
located so the power supply cord
is accessible when the washer is
in an installed position.
GROUNDING REQUIREMENTS
AWARNING: Improper connection of the
equipment-grounding conductor can result in a risk
of electrical shock.Check with a licensed electrician
if you are in doubt as to whether the appliance is
properly grounded.
1. The washer MUST be grounded.In the event of
malfunction or breakdown,grounding will reduce
the risk of electrical shock by providing a path of least
resistance for electrical current. O
2. Since your washer is equipped with a power supply
cord having an equipment-grounding conductor and
a grounding plug,the plug MUST be plugged into an
appropriate,copper-wired receptacle that is properly
installed and grounded in accordance with all local 30"
codes and ordinances or in the absence of local codes, 176 c
Min.,
with the National Electrical Codes,ANSI/NFPA 70(latest
edition).If in doubt,call a licensed electrician.DO NOT ,
cut off or alter the grounding prong on the power
supply cord.In situations where a two-slot receptacle is NOTE:The drain hose attached to the washer can reach
present,it is the owners responsibility to have a licensed
electrician replace it with a properly grounded a 58"-high standpipe.For a higher standpipe,contact an
three-prong,grounding-type receptacle. authorized parts distributor.
16
Installation Instructions
INSTALLING THE WASHER 5. Carefully move the washer to its final location.Gently rock
1. Run some water from the hot and cold faucets to flush the washer into position.It is important not to damage
the water lines and remove particles that might clog the rubber leveling legs when moving your washer
the water valve screens. to its final location.Damaged legs can increase washer
vibration.It may be helpful to spray window cleaner on
2. Remove the inlet hoses from the plastic bag.Remove the floor to help move your washer into its final position.
black rubber washers from bag and insert into hose fitting NOTE:To reduce vibration,ensure that all four rubber
before connecting to unit leveling legs are firmly touching the floor.Push and
3. (90°elbow end) pull on the back right and then back left of your
Carefully connect the inlet _� washer.
hose marked HOT to the NOTE:Do not use the dispenser drawer or door to lift
outside"H"outlet of the �. the washer.
water valve.Tighten by hand;
then tighten another 2/3 turn NOTE:If you are installing into a drain pan,you can use
with pliers.Carefully connect a 24-inch-long 2x4 to lever the washer into place.
the other inlet hose to the 6. With the washer in its
inside"C"outlet of the water final position,place °° "-
valve.Tighten by hand:then a level on top of the
tighten another 2/3 turn with pliers.Do not cross-thread washer(if the washer
or overtighten these connections. is installed under a ° °
4. Connect the inlet hose ends to the HOT and COLD water counter,the washer
faucets tightly by hand;then tighten another 2/3 turn should not be able to
with pliers.Turn the water on and check for leaks. rock).Adjust the front
leveling legs up or down
to ensure the washer
is resting solidly.Turn the locknuts on each leg
up toward the base of the washer and snug with
a wrench.
NOTE:Keep the leg extension at a minimum to prevent
excessive vibration.The farther out the legs are
extended,the more the washer will vibrate.
If the floor is not level or is damaged,you may have
to extend the rear leveling legs.
17
Installation Instructions
INSTALLING THE WASHER (cont.) 9.Turn on the power at the circuit breaker/fuse box.
7. Attach U-shaped hose guide to the end of the drain 10.Read the rest of this Owner's Manual. It contains
hose.Place the hose in a laundry tub or standpipe. valuable and helpful information that will save you
NOTE:If the drain hose is placed in a standpipe without time and money.
forming a U shape,a siphoning action could occur.There 11.Before starting the washer,check to make sure:
must be an air gap around the drain hose.A snug hose ■ Main power is turned on.
fit can also cause a siphoning action. ■ The washer is plugged in.
8. Plug the power cord into a grounded outlet. ■ The water faucets are turned on.
■ The unit is level and all four leveling legs are firmly
on the floor.
■ The shipping support hardware is removed
and saved.
■ The drain hose is properly tied up.
■ There are no leaks at the faucet,drain line
or washer.
12.Run the washer through a complete cycle.
Check for water leaks and proper operation.
13.If your washer does not operate,please review
the Before you call for service section before
calling for service.
14.Place these instructions in a location near the washer
for future reference.
i
I
REPLACEMENT PARTS
If replacement parts are needed for your washer,they can
be ordered in the United States by visiting our Website
at GEAppliances.com or by calling 800.GE.CARES.In
Canada,visit www.GEAppliances.ca or call 1.800.561.3344.
NOTE:Check to be sure the power is off at the circuit
breaker/fuse box before plugging the power cord into
an outlet.
18
Before you call for service... GE4ppliances.com
n? Troubleshooting Tips
Save time and money.Review the charts on the
following pages first and you may not need to call in
for service.
0
Problem Possible Cause What To Do
Not spinning or agitating Drain hose is kinked or • Straighten drain hose and make sure washer is not O
improperly connected sitting on it y
Household drain may • Check household plumbing.You may need to call
be clogged a plumber. 0
Drain hose siphoning;drain hose • Ensure there is an air gap between hose and drain.
pushed too for down in the drain
Washer pump filter may • Clean Pump Filter-Open the pump access door(use a coin)
be clogged and remove the pump filter by turning it counterclockwise and
pulling out Clean the filter,removing all loose debris,and put filter to
back in place. j
Load is out of balance • Redistribute clothes and run Drain&Spin or Rinse&Spin.
• Increase load size if washing small load containing heavy n
and light items. ,.f
Leaking water Door gasket is damaged • Check to see if gasket is seated and not torn.Objects O
left in pockets may cause damage to the washer(nails, (A
screws,pens,pencils).
Door gasket not damaged •Water may drip from the door when the door is opened.
This is a normal operation.
Check back left of washer • If this area is wet,you have oversudsing condition.
for water Use less detergent j
Fill hoses or drain hose is • Make sure hose connections are tight at washer and
improperly connected faucets and make sure end of drain hose is correctly n
inserted in and secured to drain facility.
Household drain may • Check household plumbing.You may need to call O
be clogged a plumber. >
Not draining Drain hose is kinked or • Straighten drain hose and make sure washer is not
improperly connected sitting on it
Household drain may • Check household plumbing.You may need to call
be clogged a plumber.
Drain hose siphoning;drain hose • Ensure there is an air gap between hose and drain.
pushed too for down in the drain
Washer pump filter may • Clean Pump Filter-Open the pump access door(use a coin)
be clogged and remove the pump filter by turning it counterclockwise and
pulling out Clean the filter,removing all loose debris,and put filter
back in place. •
Not spinning Drain hose is kinked or • Straighten drain hose and make sure washer is not sitting on it •
improperly connected
Household drain may • Check household plumbing.You may need to call a plumber. •
be clogged
Drain hose siphoning;drain hose • Ensure there is an air gap between hose and drain. `
pushed too for down in the drain
Washer pump filter may • Clean Pump Filter-Open the pump access door(use a coin)
be clogged and remove the pump filter by turning it counterclockwise and
pulling out Clean the filter,removing all loose debris,and put filter 0
back in place.
Load is out of balance • Redistribute clothes and run Drain&Spin or Rinse&Spin. y
G
• Increase load size if washing small load containing heavy
and light items.
Motor is overheated • Washer motor will stop if it becomes overheated.It will N
automatically restart after a cool-down period of up to
2 hours(if washer has not been manually turned A
Door is open • Make sure door is closed. O
19
i
Before you call for service...
Problem Possible Cause What To Do
4h
y Incomplete cycle or timer Drain hose is kinked or • Straighten drain hose and make sure washer is not
= not advancing improperly connected sitting on it
Household drain may • Check household plumbing.You may need to call
abe clogged a plumber.
N Drain hose siphoning;drain hose • Ensure there is an air gap between hose and drain.
pushed too far down in the drain
cn Washer pump filter may • Clean Pump Filter-Open the pump access door(use a coin)
be clogged and remove the pump filter by turning it counterclockwise and
pulling out Clean the filter,removing all loose debris,and put filter
u back in place.
2 Automatic load redistribution • Timer stops at 1 minute;machine has redistributed the
(A load once or twice.This is normal operation.Do nothing;
the machine will finish the wash cycle.
Loud or unusual noise, Cabinet moving • Washer is designed to move 1/4"to reduce forces
= vibration or shaking transmitted to the floor.This movement is normal.
O All rubber leveling legs are not • Push and pull on the back right and then back left of your
Q) firmly touching the floor washer to check if it is level.If the washer is uneven,adjust
Oa- the rubber leveling legs so they are all firmly touching the
floor.Your installer should correct this problem.
Unbalanced load • Open door and manually redistribute load.To check
machine,run rinse and spin with no load.If normal,
unbalance was caused by load.
C C Shipping bolts not removed • All five(5)shipping bolts should be removed before use.
,O Clothes too wet Drain hose is kinked or • Straighten drain hose and make sure washer is not
a u improperly connected sitting on it
Qi Household drain may • Check household plumbing.You may need to call
C = be clogged a plumber.
Drain hose siphoning;drain hose • Ensure there is an air gap between hose and drain.
pushed too for down the drain
Washer pump filter may • Clean Pump Filter-Open the pump access door(use a coin)
be clogged and remove the pump filter by turning it counterclockwise and
pulling out.Clean the filter,removing all loose debris,and put filter
back in place.
Load is out of balance • Redistribute clothes and run Drain&Spin or Rinse&Spin.
• Increase load size if washing small load containing heavy
and light items.
No power/washer not Drain hose is kinked or • Straighten drain hose and make sure washer is not
working or dead improperly connected sitting on it
Household drain may • Check household plumbing.You may need to call
be clogged a plumber.
Drain hose pushed too for • Ensure there is an air gap between hose and drain.
down in the drain
Washer pump filter may • Clean Pump Filter-Open the pump access door(use a coin)
be clogged and remove the pump filter by turning it counterclockwise and
pulling out Clean the filter,removing all loose debris,and put filter
O back in place.
Washer is unplugged • Make sure cord is plugged securely into a working outlet
Water supply is turned off • Turn both hot and cold faucets fully on.
Circuit breaker/fuse is • Check house circuit breakers/fuses.Replace fuses or
tripped/blown reset breaker.Washer should have separate outlet.
y Controls are not set properly • Hold START/PAUSE button to start cycle.
Automatic self-system checks • First time the washer is plugged in,automatic checks
U occur.It may take up to 20 seconds before you can use
20 your washer.This is normal operation.