HomeMy WebLinkAboutB16-0481_A9.02_1482188426.pdf3'-8"
B
BLIND
HIDDEN DOOR
FRAME
SOLID CORE
WOOD DOOR
PULL SIDE: D-PULL
PUSH SIDE: PUSHPLATE
REVEAL TO
MATCH BASE
10" BRUSHED S.S. KICK PLATE,
SEE INTERIOR ELEVATIONS
(AT BOH SIDE ONLY)
SCALE:
3/8" = 1'-0"
DOOR TYPES 2
SCALE:
PROJECT NUMBER:
DRAWING TITLE
ISSUE / REVISION
51643
SOLARIS PLAZA
141 E MEADOW DRIVE
#202
VAIL, CO 81657
SHEET NUMBER
10.26.16 PERMIT ISSUE
960 Atlantic Ave.
Alameda, CA 94501
510 865 8663
mbharch.com
12.15.16 PLAN CHECK COMMENTS
A9.02
DOOR SCHEDULE
/ DETAILS / NOTES
AS NOTED
BLIND DOOR
GROUP 1:
PASSAGE LOCKSET1 EACH
SCHLAGE # ND170-TLR FINISH: 626
CONCEALED HINGES
3 PAIR
SOSS #218-C SATIN NICKEL
CLOSER 1 EACH
DORMA 8616-TDE-COV-AWS
SILENCERS
3 EACH
TRIMCO 1229B
REAR EXIT DOOR
GROUP 5:
STOREROOM LOCKSET 1 EACH
SCHLAGE # ND96PD-TLR-ASA-80-033 FINISH: 626
HINGES 3 PAIR
HAGER BB1279 (4 1/2 X 4 1/2) US26D
CLOSER 1 EACH
AL
SILENCERS 3 EACH
TRIMCO 1229A
DOOR VIEWER 1 EACH
HAGER 1756
FLOOR STOP 1 EACH
HAGER 242F US26D
1. ALL SCHLAGE LOCKSETS TO BE PROVIDED WITH BEST 7 INTERCHANGABLE LOCK CORES.
2. PROVIDE LCN 4041 DEL CLOSER ON ALL FIRE AND SMOKE RATED DOOR ASSEMBLIES.
REFER TO REMARKS IN DOOR SCHEDULE FOR IDENTIFICATION OF RATED ASSEMBLIES.
3. PROVIDE PEMKO S88 SMOKE SEAL ON ALL FIRE AND SMOKE RATED DOOR ASSEMBLIES.
REFER TO REMARKS IN DOOR SCHEDULE FOR IDENTIFICATION OF RATED ASSEMBLIES.
4. DOOR HANDLES, LOCK AND OTHER OPERATING DEVICES SHALL BE INSTALLED AT A MIN
34" AND MAX. 48" ABOVE THE FINISHED FLOOR.
5. ALL EGRESS DOOR OPERATION SHALL ALSO COMPLY WITH SECTION 1008.1.9 - 1008.1.9.7.
HARDWARE SCHEDULE
1. THIS PROJECT SHALL COMPLY WITH ALL FEDERAL AMERICANS WITH DISABILITY ACT
REGULATIONS AND ALL LOCAL ACCESSIBILITY REGULATIONS.
2. ALL DOOR HARDWARE SHALL BE OF THE LEVER OR PUSH TYPE, MOUNTED 30" TO 44" ABOVE
THE FLOOR AND BE OPERABLE WITH A MAXIMUM EFFORT OF 5 LBS. FOR INTERIOR DOORS.
3. CONTRACTOR SHALL VERIFY WITH SUPPLIER THAT ALL HARDWARE MEETS ADA
REQUIREMENTS.
4. ALL HARDWARE SHALL BE A.N.S.I./B.H.M.A. STANDARD FINISH 626, SATIN CHROMIUM, TYPICAL
(U.O.N.)
5. THRESHOLDS SHALL BE IN COMPLIANCE WITH A.D.A., STATE AND LOCAL ORDINANCE
GUIDELINES.
6. ALL MANUALLY OPERATED FLUSH BOLTS ARE PROHIBITED ON EXIT DOORS. WHEN EXIT DOORS
ARE USED IN PAIRS AND APPROVED AUTOMATIC FLUSH BOLTS ARE USED, THE DOOR LEAF
HAVING THE AUTOMATIC FLUSH BOLT SHALL HAVE NO DOORKNOB OR SURFACE MTD.
HARDWARE. THE UNLATCHING OF ANY LEAF SHALL NOT REQUIRE MORE THAN ONE OPERATION.
7. ALL HOLLOW METAL DOORS TO BE FLUSH TYPE WITH 18 GA. FACE SHEETS WITH FOLDED
INTERLOCKED SEAM ON VERTICAL EDGES. TOP AND BOTTOM EDGES TO BE CLOSED.
8. ALL HOLLOW METAL FRAMES TO BE 16 GA. WRAP AROUND TYPE AND WELDED TYPE AT
FIRE-RATED WALL CONSTRUCTION.
9. G.C. TO PROVIDE SECURITY 180 DEGREE SECURITY EYE LENS AT ALL EXTERIOR HOLLOW METAL
DOORS AND DOORS THAT LEAD TO EXTERIOR, MOUNTED AT 8'-0" A.F.F.
10. GENERAL CONTRACTOR SHALL PROVIDE A KICK PLATE ON THE PUSH SIDE OF THE REAR EXIT
DOOR.
11. ALL HANDICAP ACCESSIBLE DOORS MUST BE MINIMUM 3'-0" W X 6'-8" H.
12. ALL DOOR APPROACHES SHALL MEET A.D.A. CLEARANCE REQUIREMENTS
13. OVERHEAD CLOSERS: (AS APPLICABLE) FURNISHED AND INSTALLED BY GENERAL CONTRACTOR.
DOOR CLOSERS TO BE MOUNTED ON ROOM SIDE OF DOORS. DOOR CLOSERS TO HAVE A
MAXIMUM OPENING FORCE OF 5 LBF (INTERIOR HINGED DOORS). THE SWEEP PERIOD OF THE
CLOSER SHALL BE ADJUSTED SO THAT FROM AN OPEN POSITION OF 70 DEGREES. THE DOOR
SHALL TAKE AT LEAST 3 SECONDS TO MOVE TO A POINT 3 IN.
14. ALL EXTERIOR HINGES TO HAVE NON-REMOVEABLE PINS.
15. TENANT'S GENERAL CONTRACTOR SHALL ENSURE ALL EXISTING DOORS TO REMAIN TO BE IN
GOOD OPERATING ORDER AND TO MEET CURRENT BUILDING CODES AND A.D.A.
REQUIREMENTS. GENERAL CONTRACTOR TO RESTORE DOORS AND HARDWARE TO "LIKE NEW"
CONDITION.
16. CONTRACTOR TO SUBMIT TYPE WRITTEN SHOP DRAWINGS AND PRODUCT LITERATURE FOR
ALL ALTERNATE SPECIFICATIONS TO DOORS AND HARDWARE SPECIFIED, PREPARED BY A
LICENSED CERTIFIED CONSULTANT.
17. G.C. TO USE KNOCK-DOWN STYLE METAL DOOR FRAMES FOR NON-RATED DOOR ASSEMBLIES.
DOOR AND HARDWARE NOTES
SILL REMARKS/NOTES
GROUP
HDWR.
MATERIAL
DOOR
SIZE LOCATION NO. TYPE
HEAD /
JAMB
MATERIAL
FRAME
OFFICE
2
3 3'-0" X 7'-0" X 1 3/4" B 1
EXISTING ENTRY DOOR TO REMAIN AS IS
EXISTING
N/A S.C. WOOD 4/A8.04 - DOOR, JAMB AND HARDWARE PROVIDED BY MILLWORK
VENDOR. JAMB INSTALLED BY G.C.. DOOR AND HARDWARE
INSTALLED BY MILLWORK VENDOR.
(E) REAR EXIT
RATING
-
ALL DOORS EQUIPPED WITH AUTOMATIC DOOR CLOSERS SHALL HAVE THE PULL FORCE REQUIRED TO OPEN THE EQUIPPED DOOR TO A MAXIMUM PULL FORCE OF 5 LBS.
ALL DOORS EQUIPPED WITH AUTOMATIC DOOR CLOSERS SHALL HAVE THE SWEEP PERIOD OF THE CLOSER TO BE ADJUSTED SO THAT FROM THE OPEN POSITION OF 70°
THE DOOR WILL TAKE AT LEAST 3 SECONDS TO MOVE TO A POINT 3" FROM THE LATCH MEASURED TO THE LANDING EDGE OF THE DOOR.
ALL EGRESS DOORS SHALL BE OPERABLE FROM THE SIDE FROM WHICH EGRESS IS TO BE MADE WITHOUT THE USE OF A KEY OR SPECIAL KNOWLEDGE OR EFFORT.
DOOR SCHEDULE
DOOR CLOSER PULL FORCE
KICK PLATE 1 EACH
TRIMCO 1229A SS
STOP 1 EACH
HAFELE - 937.51.720
PUSH PLATE
1 EACH
4"x16" ACRYLIC CLEAR
FINISH: 626
SS
DORMA 8916
HARDWARE SCHEDULE NOTES
-- (E) ENTRY 1 -- - -- --EXISTING -
EXISTING EXIT DOOR TO REMAIN AS IS
-- -- - -- -- -
12/19/16