Loading...
HomeMy WebLinkAboutA15-0050_ACPS_1432758480.pdf DN-60244:C3 ACPS-610(E) * NOTIFIER® Addressable Charger/Power Supply by Honeywell Power Supplies General The ACPS-610(E) is an auxiliary power supply with a battery •,� `` • . • S d 0 47 I'•"' • charging option and a host of special features. Selectable 0^ I` Jr :-=r charging options allow the ACPS-610(E)to provide 6 amps of • • shared power to four outputs while charging batteries from • , • ®� • 12 to 200 AH, or 10 amps of shared power when the unit is t „ARN,H�„ / \YAGg It • 9battery 9 configured for use with an external charger. Four indi- vidually ndi vidually addressable outputs can be independently configured Lamifi .a.. for auxiliary power or Notification Appliance Circuits (NAC). NAC outputs support notification appliance synchronization for devices manufactured by System Sensor®, Wheelock, and Gentex. An option to disable battery charging allows the sys- • • • • • • • tern designer to use the four built-in circuits to distribute • • • • • • • 10 amps of power for general purposes, excluding NAC appli- �� • • • • • • • cations. flu; _ ;. t • , • • • •- • • 0 • • • • _ The ACPS-610(E) is compatible with NOTIFIER intelligent fire � • • • G • • • alarm control panels using CLIP and FlashScan®protocol • �`� • • • Features • Certified for seismic applications when used with the appro- priate seismic mounting kit. Specifications • Approved for Marine applications when used with listed compatible equipment(see DN-60688). • Primary(AC) power: • Provides 6.0 A of NAC power or 10 A of general purpose -ACPS-610: 120 VAC,50/60 Hz input,5.0 A maximum. power. -ACPS-610E: 220/240 VAC, 50/60 Hz input, 2.5 A maxi- • Four Class B (Style Y) or four Class A (Style Z) outputs, mum. individually addressable by the FACP. • Output voltage: 24 VDC electrically regulated and power • When built-in outputs are configured for NAC operation, limited (under primary AC mains). Under secondary power, each circuit supports strobe synchronization with the follow- 20.4 to 26.4 VDC. ing manufacturers' audio/visual devices: System Sensor® • Output circuits-TB3, TB4,TB5,TB6 on Main Board: 1.5 A (SpectrAlert® and SpectrAlert Advance Series) or Whee- maximum for any NAC output circuit. 2.5 A maximum for lock or Gentex. any Power output with battery charger disabled. • Each circuit can be software-selected for use as: a Notifica- • Secondary power (battery) charging circuit- lead-acid bat- tion Appliance Circuit,general purpose 24 VDC power,four- tery charger which will charge 12 to 200 AH batteries. Max- wire detector power,or door holder. imum charger current-5.0 A. • Steady, March Time (120 PPM), Two Stage, Temporal, or • Secondary power auxiliary outputs-TB2 on CPS-24 Board: UZC Zone-Coded and Non-Coded devices - software- -24V @ 0.5A, power limited. selectable by circuit. -5V @ 0.15A, power limited. • Universal Zone Coder (UZC 256) option supports for pro • Wiring: utilizes wire sizes 12 to 18 AWG(3.1 to 0.78 mm2). grammable coded outputs. Up to 256 different codes. • Auxiliary Outputs:24V @ 0.5A and 5V @ 0.15A. • SLC specifications: Average SLC current is 1.287 mA. SLC data is transmitted between 24.0 VDC, 5 VDC, and 0 VDC • Charges 12 to 200 AH batteries with full supervision. The at approximately 3.33 Kbaud. charger on the ACPS may be disabled via software. When • Battery fuse(F2): 15A, Fast acting. disabled,a separate,external charger is required,for exam- ple a CHG-120. • Weight:4.5 lb. • May be used to provide battery backup for multiple ACPS supplies. ACPS Programming • AC loss detection, brownout detection, and AC loss delay The ACPS-610(E) is programmable via the simple-to-use reporting. PK-PPS programming utility, which requires a Windows® PC • Power-limited outputs. with a USB port and cable. Programming may be performed • Isolated Signaling Line Circuit(SLC) interface. during an on-line session with the ACPS-610(E),or previously saved programs may be downloaded to individual ACPS- • Selectable ground fault detection. 610(E) units.The ACPS-610(E)requires the use of a minimum • Canadian two stage operation. of 5 SLC address points, and will use up to 14 SLC address points to fulfill requirements for Canadian supervision and two stage operation. NOTE: PK-PPS is available for download from www.magni- fire.com. DN-60244:C3•4/23/2012—Page 1 of 2 Product Line Information Configuration Summary El ACPS-610:Addressable charger power supply,with selectable Label 01 SLC Addressing: built-in synchronization, and four built-in control modules. Sev- Chargec 50 charge(55•200 AH) Monter General: b Sync Type: External(UZC) Output 1: b•1 eral mounting options available(see below). ni Syslerrr Sensor Inlanal Output 2: b•2 Siurceable Yes Output 3: b•3 ACPS-610E: Same as ACPS-610, but configured for 220/240 Repotting US AC Fail Output 4: b r 4 g Delay: 2 bouts Signal Silence: b•5 VAC operation. ❑utpotl_ HACSynchronized CAB-PSI: The CAB-PSI can house one ACPS-610(E) and Output 2 NAC Synchronized Outputa NAC Constant two 12 AH batteries. Dimensions: 15.218" (38.654 cm) high x Output 4: Power Resettable 14.5"(36.83 cm)wide x 3.562" (9.048 cm)deep with door. SEISKIT PS/2/4: Seismic kit for mounting ACPS-610 in a CAB-PSI. Includes bracket for two 12 AH batteries. DR-PSI: When installing an ACPS-610(E) into an older ver- <Back I Finish I Cancel I A sion of the CAB-PSI used for an ACPS-2406(E), the new • wider door must be ordered for use with the older version Example of Programming cabinet. for the ACPS-610 Using 6 Addresses BB-25: The BB-25 can house one ACPS-610(E) and two 12 volt,26 AH batteries. BB-100:The BB-100 can house one ACPS-610(E)and two 12 Configuration Summary Fl volt,55 AH or 100 AH AH batteries. Label: 01 SLCAddressing: BB-200: The BB-200 can house one ACPS-610(E) and four Charger: SAcharge155-200 AH) Wok,General: b 12 volt, 100 AH batteries. Code Typo: Canadian Output 1: b•1 Dual Stage: 2 Output 2: b«2 Sync Type: External(UZC) Output3: b«3 CAB-4 Series: The ACPS-610(E) can mount in any of the w/System Sensor Internal Output4: b•4 CAB-4 Series cabinets with CHS-PS or CHS-BH. See DN- Silenceablo Yes Signal Silence: b•5 Reporting: Canadian Trouble Monitoring, 6857. AC Faik b«6 Output 1: NAC Powe Res FBaith F. b«7 EQ Cabinet Series: The ACPS-610(E) can mount in any of Output 2: Power Rese¢able Faith Fault. b•6 Output 3: Door Holler 30 Sec Release Charger b•9 the EQ Cabinet Series cabinets using CHS-6.See DN-60229. Output 4: NAC Synchronized Dual Stage: Output"I: b•11 MARINE-EQ System: Protects equipment in shipboard and Output : b+12waterfront applications. For a full list of required and optional Output4: b«133 Pp q p equipment,see DN-60688. <Sank Finish Camel I g CHS-PS/CHS-6: Chassis used to mount the ACPS-610(E) in row 1,2,or 3 of the CAB-4 or EQ series enclosure. Example for ACPS-610 CHS-BH: Battery mounting chassis that holds up to two 12AH Using Canadian Reporting with Two Stage batteries on a CHS-PS. Batteries: ACPS-610(E) battery charging circuit range is 12 - 200 AH.See DN-6933. Listings and Approvals These listings and approvals apply to the modules specified in this document. In some cases,certain modules or applications may not be listed by certain approval agencies, or listing may be in process. Consult factory for latest listing status. • UL Listed: S635. • ULC Listed: S635. • FM Approved. • CSFM: 7315-0028:0248, 7165-0028:0224, 7165- 0028:0243. • MEA#30-08-E. • FDNY: COA#6085,#6098. When used with the MARINE-EQ, appropriate seismic bracket, and marine approved devices, the ACPS-610(E) is approved by the following agencies: • US Coast Guard: 161.002/50/0(Standard 46 CFR). Notifier®, FlashScan®, System Sensor®, and SpectrAlert®are registered • Lloyd's Register: 11/600013(ENV 3 category). trademarks of Honeywell International Inc. Windows® is a registered trademark of Microsoft. • American Bureau of Shipping(ABS). ©2012 by Honeywell International Inc.All rights reserved.Unauthorized use of this document is strictly prohibited. This document is not intended to be used for installation purposes. :--..:::::;«: ISO 9001 .�� We try to keep our product information up-to-date and accurate. We cannot cover all specific applications or anticipate all requirements. ENGINEERING A MANUFACTURING All specifications are subject to change without notice. QUALITY SYSTEMS Made in the U.S.A. For more information,contact Notifier.Phone:(203)484-7161,FAX:(203)484-7118. www.notifier.com Page 2 of 2—DN-60244:C3•4/23/2012