Loading...
HomeMy WebLinkAboutA15-0087_PID-95_1444243620.pdf Gamewell PID-95 I' PID-95 FIRESTCORUMENTSLNTRO Fc' IN by Honeywell Description Point Identification Device The Gamewell-FCI PID-95P addressable point identifica- tion device is the interface between the non-powered, nor- mally open, dry-contact devices and Gamewell-FCI's 600 Series and IL195-E3 Series° of analog addressable Fire � 4Gamewell-FCI• Alarm Control Panels (FACPs). Point identification devices Pl 95P LI �R' monitor a single Style B circuit, and are designed for con- ®It' 1 cealed mounting in an electrical backbox.The PID-95P can ^°15P 5I be surface or flush mounted and has a visible LED for alarm/annunciation. Operation l , The point identification device connects to the Signaling PID 95P PID 95 Line Circuit (SLC) via two wires. The PID-95 will monitor, via a two-wire supervised SLC circuit, contact-type devices Features such as a waterflow switch or a manual station. Upon acti- vation of the monitored device, the PID-95 will report its address to the 600 Series and ILl95-E3 Series FACP via • Compatible with the Gamewell-FCI, 600 Series and the analog SLC. The control panel will then activate into all ILI95-E3 Series Systems alarm programmed outputs related to the PID-95. • Monitors dry-contact devices Programming • LED for alarm annunciation • Field programmable The PID-95 is programmed by setting a single DIP switch, • Priority interrupt easily accessible on the device's printed circuit board. The • Plate-mounted version available for surface or flush DIP switch sets the address of the device and the priority mounting in a 4"x 4.688"(10.16 cm x 11.908 cm)double interrupt (DIP SW #8). All other programming is accom- plished at the FACP through a laptop computer or the con- trol panel operator's display. (600 Series only). Standard Application The PID-95 is the interface between the dry-contact type devices and the SLC of the control panel. The PID-95 is a means of connecting and identifying monitor points without the use of conventional input modules at the main control panel.The use of PID-95s can dramatically reduce the field wiring required on many projects. An ISO 9000-2000 Company SIGNALING E3 Series®is a registered trademark of Honeywell International Inc. U� fOo Microsoft®Windows®is a registered trademark of Microsoft®Corporation. LISTED® MEA S521 APPROVED Approved 7300-1703:135 GAMEWELL-FCI 12 Clintonville Road, Northford,CT 06472-1610 USA•Tel:(203)484-7161 •Fax:(203)484-7118 Specifications are for information only,are not intended for installation purposes,and are subject to change without notice.No responsibility is assumed by Gamewell-FCI for their use. ©2008 by Honeywell International Inc. All rights reserved. www.gamewell-fci.com CS-2044 Rev.B page 1 of 2 Engineer's Specifications Ordering Information Addressable interface devices shall be provided for the monitoring and supervision of contact type devices con- Part Number Description nected to the Fire Alarm Control Panel. The devices shall PID-95 Addressable point identification device monitor a normally open dry contact. The addressable for monitoring contact devices interface devices shall communicate to the main control PID-95P Addressable input interface device panel via the analog addressable circuit. The interface mounted on 4.688"(11.908 cm) plastic plate device shall be Gamewell-FCI PID-95P or PID-95. 70839 Trim ring for flush mounting on the PID 95P Specifications PID-95P Standby Current: 0.0005A, 0.0008A Alarm Current: 0.0015A Operating Temperature: 32°F to 120°F(0°C to 49°C) Relative Humidity: 93%, non-condensing Dimensions: 4"x 4.688"(10.16 cm x 11.908 cm), double gang backbox PID-95 Standby Current: 0.0005A, 0.0008 A Alarm Current: 0.0015A Operating Temperature: 32°F to 120°F(0°C to 49°C) Relative Humidity: 93%, non-condensing Dimensions: 4"(10.16 cm)square backbox with blank cover plate GAMEWELL-FCI 12 Clintonville Road, Northford,CT 06472-1610 USA•Tel:(203)484-7161 •Fax:(203)484-7118 CS-2044 Rev.B page 2 of 2 www.gamewell-fci.com