HomeMy WebLinkAboutB14-0153_3.5_1421429100.pdf 40,1 Fpakif4.
4sAppli°
Job Truss Truss Type 'Qty Ply
ML07779 05 Monopitch Supported Gable 1 I 41 illiot 11
I LA el
Overholt Truss, Delta.Co 81416
ID,rfg9ZcmtZ id
I 10-11-8
10-11-8 114 rigi
Nit
3.00 12 4
2 '•f
olo) IPI*s
-
01/16/15
•—
12
1
jc — —
Co e e e l e
— e
d ���
V .'r • • Y//,jai.•„ /
• //. ',5<X/x5x • • >..' '50<5.</ //3:‘,/< •• /1/,
11 10 9 8 7
3x4
1
LOADING(psf) SPACING 2-0-0 CSI DEFL in (loc) 1/defl Lid PLATES GRIP
TOLL 80.0 Plates Increase 1.00 TC 0.42 Vert(LL) n/a - n/a 999 MT20 197/144
(Roof Snow=80.0) Lumber Increase 1.00 BC 0.20 Vert(TL) n/a - n/a 999
TCDL 15.0 Rep Stress Incr YES WB 0,16 Horz(TL) -0.00 7 n/a n/a
BCLL 0.0
BCDL 10.0 Code IRC2012/TP12007 (Matrix) Weight:43 lb FT=0%
LUMBER BRACING
TOP CHORD 2x6 SPF 1650F 1.5E TOP CHORD Structural wood sheathing directly applied or 6-0-0 oc purlins, except
SOT CHORD 2x4 SPF 1650F 1,5E end verticals.
WEBS 2x4 SPF 1650F 1.5E BOT CHORD Rigid ceiling directly applied or 10-0-0 oc bracing.
OTHERS 2x4 SPF 1650F 1.5E
REACTIONS All bearings 10-11-8.
(Ib)- Max Horz 1=120(LC 7)
Max Uplift All uplift 100 lb or less at joint(s)1,7,8,9 except 10=-304(LC 16),11=-122(LC 10)
Max Gray All reactions 250 lb or less at joint(s)7,10 except 1=489(LC 16),8=326(LC 16),9=411(LC 16),
11=1553(LC 16)
FORCES (Ib)-Max.Comp./Max.Ten.-All forces 250(Ib)or less except when shown.
WEBS 5-8=-311/31,4-9=-353/47,2-11=-1361/174
NOTES
1)Wind:ASCE 7-10;Vult=115mph(3-second gust)V(IRC2012)=91mph:TCDL=6.Opsf;BCDL=6.0psf;h=25ft;Cat.II;Exp C;enclosed;
MWFRS(envelope)automatic zone;cantilever left and right exposed;end vertical left and right exposed;Lumber DOL=1.00 plate grip
DOL=1.00
2)Truss designed for wind loads in the plane of'the truss only. For studs exposed to wind(normal to the face),see Standard Industry
Gable End Details as applicable,or consult qualified building designer as per ANSUTPI 1.
3)TCLL:ASCE 7-10;Pf=80.0 psf(flat roof snow);Category II;Exp C;Partially Exp.;Ct=1.1
4)Unbalanced snow loads have been considered for this design.
5)All plates are 2x4 MT20 unless otherwise indicated.
6)Gable requires continuous bottom chord bearing.
7)Gable studs spaced at 1-4-0 oc. ````�"`
8)This truss has been designed for a 10.0 psf bottom chord live load nonconcurrent with any other live loads. =� `Nt
9)Provide mechanical connection(by others)of truss to bearing plate capable of withstanding 100 lb uplift at joint(s)1,7,8,9 except �0p0 0 LICF�1,
(jt=1b)10=304,11=122. ..••••••. s I1
10)This truss is designed in accordance with the 2012 International Residential Code sections R502.11.1 and R802.10.2 and referenced o G�•.• p.. HF,q•. (�( t
standard ANSI/TPI 1. ire
co
/� :0 v•
LOAD CASE(S) Standard
. Q
i
August 6,2014
I •
Q WARMNO-Verify design parameters and READ NOTES ON MIS AND INCLUDED MITER REFERENT PAGE 1411-1413 re¢1/29/2014 BEFORE 115E
Design valid for use only with MiTek connectors.This design is based only upon parameters shown,and is for an individual building component. �
Applicability of design parameters and proper incorporation of component is responsibility of building designer-not truss designer.Bracing shown y�
is for lateral support of individual web members only.Additional temporary bracing to insure stability during construction is the responsibillity of the MiTele
erector.Additional permanent bracing of the overall structure is the responsibility of the building designer.For general guidance regarding
fabrication,quality control,storage,delivery,erection and bracing,consult ANSI/711 Qualty Criteria,OSB-89 and SCSI Building Component 7777 Greenback Lane,Suite 109
Safety Information available from Truss Plate Institute,781 N.Lee Street,Suite 312,Alexandria.VA 22314. Citrus Heights,CA,95610
If Southern Pine ISPI lumber is specified.the design values are those effective 06/01/2013 by Also