HomeMy WebLinkAboutF17-0007_sammy swg 25-380_1493227560.pdf5 To find a distributor near you, call 800-BUILDEX
Not less than 2” nominal width
(1-1/2”) up to 3-1/2” pipe; not less than
3” (2-1/2”) nominal width 4” & 5” pipe
Minimum 2-1/2” from bottom for
branch lines. Minimum 3” from
bottom for main lines. Exception: This
requirement shall not apply to 2” or
thicker nailing strips resting on top of
steel beams.
Floor Joist
HORIZONTAL MOUNT
WOOD WOOD WOOD WOOD WOODSIDEWINDERS® for Wood Installs HORIZONTALLY into the side of wood structures easily and quickly!
Approvals Rod
Size
Part
Number Model Screw
Descriptions
Ultimate
Pullout (lbs)
UL Test
Load (lbs)
Box
Qty
Case
Qty
1/4" 8018957 SWG 100 1/4 x 1" 622 (Fir) 25 125
1/4" 8019957 SWG 200 1/4 x 2" 1725 (Fir) 25 125
3/8" 8020957 SWG 10 1/4 x 1" 622 (Fir) 300 25 125
3/8" 8021957 SWG 20 1/4 x 2" 1725 (Fir) 1050 25 125
3/8" 8073925 SWG 20-SS 1/4 x 2" 1725 (Fir) 850 25 125
3/8" 8022925 SWG 25-380 3/8 x 2-1/2" 2249 (Fir) 1500 25 125
3/8" 8023925 SWG 30 1/4 x 3" 1884 (Fir) 25 125
#14 SW Red
Nut Driver
Part # 8114910
SPECIAL NUT DRIVER SYSTEM: The nut drivers were designed with a unique spin-off feature which provides a fast and safe installation each time. When the face of the driver comes into
contact with the material you are installing into, continue drilling until nut driver spins free. Installation is then complete. Warranty requires the use of the appropriate nut driver for installations.
INSTALLATION STEPS - VERTICAL INTO WOOD & STEEL:
1. Insert the appropriate nut driver into a 3/8” or 1/2” portable drill.
2. Insert the SAMMYS into the #14 (black) nut driver (p/n 8113910). Drill
should be in a vertical position.
3. Push the face of the nut driver tight to the member. When the
nut driver spins freely on the SAMMYS, stop drill and remove.
4. The SAMMYS is now ready to receive 1/4”, 3/8”, 1/2” or metric
all thread rod, bolt stock. (The 1/2” requires the #14SW red nut driver)
Note: When installing DSTR, follow the above instructions,
then add retainer nut and torque to 20 foot lbs. for maximum
pullout in purlin steel.
INSTALLATION STEPS - HORIZONTAL INTO WOOD & STEEL:
1. Insert the appropriate nut driver into a 3/8” or 1/2” portable drill.
2. Insert the SAMMYS into the #14SW (red) nut driver (p/n 8114910). With drill
unit in a horizontal position and at a right angle to the structural member,
begin installation.
3. When the nut driver spins free on the SAMMYS, stop the drill and
remove.
4. The unit is now ready to receive 1/4”, 3/8” or metric all thread rod or
bolt stock.
Note: When installing SWDR, follow the above instructions, then add retainer nut
and torque to 20 foot lbs. for maximum pullout in purlin steel.
Composite/Truss
Consult truss manufacturer for
recommended installation point.
*Pre-drilling may be required for Model
SWG 25-380 (tools available on pg 10 )
Product Features
• No pre-drilling required.
• Quick to install using the Sammy
Nut Driver with an 18V cordless
drill/driver.
• Saves time from traditional
methods.
• Reduces installation cost.
• Made in the U.S.A.