Loading...
HomeMy WebLinkAboutF17-0013_Cut sheets_1494971520.pdf TABLE OF CONTENTS 1. SPRINKLER PIPE AND FITTINGS 2. SPRINKLER HEADS 3. WET PIPE RISER 4. HANGER MATERIAL The Riser Manifolds described in thistechnical data sheet provide the nec-essary waterflow alarm, pressuregauge, and drain equipment in a singleassembly for use in NFPA 13D or 13Rresidential sprinkler systems as fol- lows: Figure 513D (13D) 1 Inch (DN25)Female Thread x Female Thread Figure 513D/R (13D/R) 1-1/2 Inch (DN40)Male Thread x Female Thread Male Thread x Male Thread Figure 513D/R (13D/R)2 Inch (DN50) Groove x GrooveMale Thread x Groove The variety of sizes and end connec-tions allow cost effective and easytransition to check valves, controlvalves, and system piping. The RiserManifolds may be installed in either thehorizontal (flow switch on top) or verti-cal (flow going up). The Figure 513D (13D) and 513D/R(13D/R) Riser Manifolds with a covertamper switch for the waterflow alarmswitch are UL Listed, ULC Listed, andFM Approved. The Figure 513D (13D) and 513D/R(13D/R) Riser Manifolds without a cover tamper switch for the waterflowalarm switch are UL Listed and FM Approved. 175 psi (12,1 bar) The manifold body of the Figure 513 is ductile iron, whereas the manifoldbody of the Figure 13 is cast iron. The two assemblies are completely inter-changeable in function, application, and end-to-end laying length. Red painted. The Riser Manifolds may be installed in either the horizontal (flow switch ontop) or vertical (flow going up). The inlet of the Riser Manifold may be di-rectly connected to a shut-off control valve. Install the manifold body with the flow arrow pointing in the down-stream position using threaded con-nections and/or listed mechanicalgrooved connections, as applicable. Connect the drain line, and then close the drain valve. Refer to Figure 4 for wiringguidance. All wiring must be per-formed in accordance with the Author- ity Having Jurisdiction and/or the Na-tional Electrical Code. Place the system in service by filling the system with water. When fill-ing the system, partially open the con- trol valve to slowly fill the system. After the system is fully pressurized,completely open the control valve. Secure all supply valvesopen. Tel: (800) 381-9312 / Fax: (800) 791-5500 4-1/2" to the Waterflow Alarm Switches. Cover Tamper Switches installed internal ULC Listed Manifolds are equipped with (114,3 mm) 10" (254,0 mm) Approximate weight, 7.5 lbs. (3,4 kg).1. 2. NOTES: 3/4" NPT (92,1 mm) 3-5/8"1 (73,0 mm) 2-7/8" 9-3/4" (247,7 mm) Waterflow 3 2 CH: Common Hardware3. (88,9 mm) 3-1/2" Paddle and Cover Tamper VSR-SF modified with QTY.DESCRIPTION Female x Female NPT 1" Manifold Body, Water Pressure Gauge 200 psi/1400 kPa VSR-SF modified with Waterflow Alarm Switch: 1 3 2 NO. . . 1 . . . 1 N/A 2343 P/N Paddle, UL/FM . . . . . . . . 1 971-096-01 Switch, ULC/FM 1 976-519-01. . . . . . . . (Normally Closed) Drain Valve (136,5 mm) 5-3/8" (288,9 mm) 11-3/8" Male x Male NPT Manifold 11-1/8" (282,6 mm) (54,0 mm) Male x Female NPT Manifold 10" (254,0 mm) NPT 2-1/8" 1" (114,3 mm) 4-1/2" Waterflow 3 2 to the Waterflow Alarm Switches. Cover Tamper Switches installed internal ULC Listed Manifolds are equipped with Approximate weight, 8.7 lbs. (3,9 kg).1. 2. NOTES: CH: Common Hardware3. (88,9 mm) 3-1/2" QTY.DESCRIPTION 1-1/2" Manifold Body,Male x Female NPT Water Pressure Gauge 300 psi/2000 kPa3 2 1 NO. . . 1 . . . . . 1 2341 N/A P/N Switch, ULC/FM. . . . . . . . 1 976-519-02 . . . . . . . . . Waterflow Alarm Switch:VSR-SF modified with VSR-SF modified withPaddle and Cover Tamper Paddle, UL/FM 971-096-001 1 (Normally Closed) Drain Valve Male x Male NPT . . . . . . . 1 N/A The following inspection proceduremust be performed as indicated, in ad-dition to any specific requirements ofthe NFPA, and any impairment mustbe immediately corrected. The owner is responsible for the in- spection, testing, and maintenance oftheir fire protection system and de- vices in compliance with this docu-ment, as well as with the applicable standards of the National Fire Protec-tion Association (e.g., NFPA 25), in addition to the standards of anyauthority having jurisdiction. The in- stalling contractor or product manufac-turer should be contacted relative to any questions. It is recommended that automaticsprinkler systems be inspected,tested, and maintained by a qualifiedInspection Service in accordance withlocal requirements and/or nationalcodes. Fully open the drain valve. Make certain that drainage water willnot cause any damage or injury. Verify that the residual (flow-ing) pressure indicated by the pres- sure gauge is no less that originallyrecorded for the system when it was first installed. Close the drain valve. Verify that the static (not flow- ing) pressure indicated by the pres-sure gauge is no less that originally recorded for the system when it wasfirst installed. Temporarily install a test ori-fice in the drain line outlet. Fully open the drain valve.Make certain that drainage water will not cause any damage or injury. Verify operation of the associ-ated alarms. Close the drain valve. Remove the test orifice fromthe drain line outlet. Fully open the Inspector’s Test Connection Valve. Make certain thatdrainage water will not cause any dam- age or injury. Verify operation of the associ-ated alarms. Close the Inspector’s TestConnection Valve. Optionally Supply End Grooved or Male NPT (57,2 mm) (114,3 mm) 2-1/4" 2. ULC Listed Manifolds are equipped with Cover Tamper Switches installed internal to the Waterflow Alarm Switches. . . . . . . . 1 N/AGroove x Groove Male NPT x Groove 300 psi/2000 kPa Water Pressure Gauge Approximate weight, 11.0 lbs. (5,0 kg). NOTES: 1. 3 2 5-7/16" (138,1 mm) 1" NPT 4-1/2" . . 1 2341 (304,8 mm) 12" N/A1. . . . . Waterflow DESCRIPTION 2" Manifold Body,1 NO. P/NQTY. 3 2 CH: Common Hardware3. ULC/FM . . . . . . . . . . . . . . 1 976-520-01 . . . . . . . . . . . . . . . Waterflow Alarm Switch: VSC with Paddle, VSC with Paddle and Cover Tamper Switch, UL/FM 976-357-011 13" (330,2 mm) Male NPT x Groove Groove x Groove, Connection (88,9 mm) 3-1/2" 1 (Normally Closed) Drain Valve INCOMING OUTGOING SINGLE CONDUCTOR TERMINAL PLATE LOOPED SECTION UNINSULATED CLAMPING CONDUCTORS SEPARATE STRIPPED ENDS CLAMPING TERMINALPLATE SEVERED An uninsulated section of a single conductor is not permitted to be looped around the terminal and serve as two separate connections. The wire must be severed to serve as two separate connections, thereby providing supervision of the connection in the event that the wire becomes dislodged from the terminal. COM NCNO NO FLOW CONTACTS SPDT (Form C) 5A @ 125 VACCONTACT RATING 2.5A @ 30 VDC . . . . . . . . . . . . . . COM NO NC POWER SIGNAL LOCAL DEVICE NON-SUPERVISED CIRCUITCONDITION END OF LINE RESISTOR COM SUPERVISED CIRCUIT STYLE B/CLASS B CONTROL NO NC PANEL signaling unit, while the other contact is used to operate a local audible or visual annunciator. Switch has two switches, one can be used to operate a central station, proprietary or remove For supervised circuits, see "Switch Terminal Connections" above. The Waterflow Alarm (SEE NOTE) CONTACTS SHOWNWITH COVER IN PLACE COM . . . . . . . . . . . . . .CONTACT RATING NO CONTACTS 3A @ 250 VAC 5A @ 125 VAC NC SPDT (Form C) 1mA @ 5 VDC min. Products manufactured by Tyco Fire &Building Products (TFBP) are war- ranted solely to the original Buyer forten (10) years against defects in mate- rial and workmanship when paid forand properly installed and maintained under normal use and service. Thiswarranty will expire ten (10) years from date of shipment by TFBP. Nowarranty is given for products or com- ponents manufactured by companiesnot affiliated by ownership with TFBP or for products and components whichhave been subject to misuse, improper installation,corrosion, or which havenot been installed, maintained, modi- fied or repaired in accordance with ap-plicable Standards of the National Fire Protection Association, and/or thestandards of any other Authorities Having Jurisdiction. Materials foundby TFBP to be defective shall be either repaired or replaced, at TFBP’s soleoption. TFBP neither assumes, nor authorizes any person to assume for it,any other obligation in connection with the sale of products or parts of prod-ucts. TFBP shall not be responsible for sprinkler system design errors or inac-curate or incomplete information sup- plied by Buyer or Buyer’s repre-sentatives. In no event shall TFBP be liable, incontract, tort, strict liability or underany other legal theory, for incidental,indirect, special or consequential dam- ages, including but not limited to laborcharges, regardless of whether TFBP was informed about the possibility ofsuch damages, and in no event shall TFBP’s liability exceed an amountequal to the sales price. The foregoing warranty is made in lieu of any and all other warranties, ex-press or implied, including warranties of merchantability and fitness fora par-ticular purpose. This limited warranty sets forth the ex-clusive remedy for claims based on failure of or defect in products, materi-als or components, whether the claim is made in contract, tort, strict liabilityor any other legal theory. This warranty will apply to the full ex- tent permitted by law. The invalidity, inwhole or part, of any portion of this warranty will not affect the remainder. Specify; Size (specify), Figure (specify 513D or 513D/R, (specify connectiontype inlet x outlet) Riser Manifold (specify - without or with) a cover tam-per switch for the waterflow alarm switch, P/N (specify). 1 Inch (DN25) FT x FT. . . . . . . . . . . . . . . P/N 4085 1-1/2 Inch (DN40) MT x FT . . . . . . . . . . . . . . P/N 40881-1/2 Inch (DN40)MT x MT . . . . . . . . . . . . . . P/N 4089 2 Inch (DN50) G x G . . . . . . . . . . . . . . . . P/N 4093 2 Inch (DN50)MT x G . . . . . . . . . . . . . . . P/N 4094 1 Inch (DN25) FT x FT. . . . . . . . . . . . . . . P/N 40471-1/2 Inch (DN40)MT x FT . . . . . . . . . . . . . . P/N 40571-1/2 Inch (DN40) MT x MT . . . . . . . . . . . . . . P/N 4058 2 Inch (DN50)G x G . . . . . . . . . . . . . . . . P/N 40592 Inch (DN50)MT x G . . . . . . . . . . . . . . . P/N 4064 Specify: (description) for use with Fig- ure 513D, 513D/R, 13D, or 13D/RRiser Manifold, P/N (Ref. Figure 1, 2or 2, as applicable). data sheet The information contained herein is produced in good faith and is believed to be reliable but is for guidance only. ARGCO and its agents cannot assume liability or responsibility for results obtained in the use of its product by persons whose methods are outside or beyond our control. It is the user's responsibility to determine the suitability of any of the products, methods of use, or preparation prior to use, mentioned in our literature. It is the user's responsibility to observe and adapt such precautions as may be advisable for the protection of personnel and property in the handling and use of any of our products. FOR MORE INFORMATION CALL ARGCO AT 1-800-854-1015 OR LOG ONTO WWW.ARGCO.COM PART # 65-20-105 65-20-110 65-20-115 65-20-120 65-20-125 65-20-130 A 2.07” 2.36” 2.62” 3.17” 3.54” 4.25” SIZE 1/2” 3/4” 1” 1-1/4” 1-1/2” 2” B 2.13” 2.30” 2.62” 3.07” 3.43” 4.21” DIMENSIONS B A MATERIAL CAST BRASS CAST BRASSCAST BRASSRUBBER BRASS ROD BRASS ROD PART CAPBODY SEAT HOUSE SEAT GASKET PIN LOCK BOLT MATERIALS •Built for a tight seal on backflow •Water, oil & gas - 200 psi •1/2” to 2” IPS •Cast Brass Construction NOT recommended for pulsating or vibrating service nut & washer on gasket Horizontal Swing Check Valve Inline Check Valve PART # 65-20-140 65-20-145 65-20-150 65-20-151 SIZE 1” IPS 1-1/4” IPS 1-1/2” IPS 2” IPS Spring loaded, Buna-N Seat Horizontal or Vertical installation Body End piece Stem Spring Seat Forged brass Forged brass Plastic Stainless steel Buna-N MATERIALS A 2.32” 2.64” 2.75” 3.15” B 1.77” 2.20” 2.48” 3.11”A B DIMENSIONS Horizontal Swing Check Valve MFG. #5400928 - REV D-1 12/10PRINTED IN USA PAGE 1 OF 3 PS10 SERIES PRESSURE SWITCH Installation The Potter PS10 Series Pressure Actuated Switches are designed for the Wiring Instructions conduit wiring. Testing Wet System Method 1 UL, cUL, and CSFM Listed, FM and LPC Approved, NYMEA Accepted, CE Marked Dimensions: Conduit Entrance: Enclosure: Pressure Connection: Factory Adjustment: Differential: Maximum System Pressure: Switch Contacts: Service Use: Method 2 Testing: Note: Wet System With Excess Pressure Testing: Dry System Testing: Note: Tamper Ordering Information PS10-1 Pressure switch with one set 1340103 SPDT contacts PS10-2 Pressure switch with two sets 1340104 SPDT contacts PRESSURE SWITCH MFG. #5400928 - REV D-1 12/10PRINTED IN USA PAGE 2 OF 3 PS10 SERIES PRESSURE SWITCH Typical Sprinkler Applications Switch Clamping Plate TerminalDimensions Low Pressure Signal Connection Fig. 2 Fig. 4 Fig. 5 Fig. 3 Fig. 1 PRESSURE SWITCH MFG. #5400928 - REV D-1 12/10PRINTED IN USA PAGE 3 OF 3 PS10 SERIES PRESSURE SWITCH One Conduit Wiring Fig. 9 Removing KnockoutsSwitch Operation Fig. 8 indication. PRESSURE SWITCH SAMMYS® FOR WOOD Part No. Model Rod Size Mount Direction UL Max Pipe Size UL Test Load (lbs) UL Min Wood Thickness FM Max Pipe Size FM Test Load (lbs) FM Min Wood Thickness 8007957 GST 10 3/8” Vertical CPVC 1-1/2” 300 1-1/2” 8020957 SWG 10 3/8” Horizontal CPVC 1-1/2” 300 1-1/2” 8008957 GST 20 3/8” Vertical 2-1/2” 850 1-1/2” 4” 1475 1-1/2” 8068925 GST 20-SS 3/8” Vertical 2-1/2” 850 1-1/2” 8010957 GST 30 3/8” Vertical 4” 1500 1-1/2” 4” 1475 1-1/2” 8009925 GST 25-380 3/8” Vertical 4” 1500 1-1/2” 8022925 SWG 25-380 3/8” Horizontal 3-1/2” - 4”* 1500 1-1/2” 8021957 SWG 20 3/8” Horizontal 2-1/2” - 3”** 1050 1-1/2” 8073925 SWG 20-SS 3/8” Horizontal 2-1/2” 850 1-1/2” 8139957 SH-GST 20 3/8” 17° Angle off Vertical 3” 1050 1-1/2”4” 1475 1-1/2” 8141957 SH-GST 30 3/8” 17° Angle off Vertical 4” 1500 1-1/2”4” 1475 1-1/2” 14 For the most up to date information, visit www.sammysuperscrew.com SAMMYS® FOR STEEL Part No. Model Rod Size Mount Direction UL Max Pipe Size UL Test Load (lbs) UL Min. Steel Thickness FM Max Pipe Size FM Test Load (lbs) FM Min. Steel Thickness 8038957 DSTR 1 3/8” Vertical 4” 1500 .035” 4” 1475 .105” 8037957 DSTR 1-1/2 3/8” Vertical 4” 1500 .035” 4” 1475 .105” 8039957 DSTR 516 3/8” Vertical 4” 1500 .037” 4” 1475 .105” 8045957 DST 516 3/8” Vertical 4” 1500 .188” 4” 1475 .188” 8046957 TEK 50 3/8” Vertical 4” 1500 .250” 4” 1475 .188” 8055957 SWDR 1 3/8” Horizontal 4” 1500 .037” 4” 1475 .060” 8056957 SWDR 516 3/8” Horizontal 4” 1500 .037” 4” 1475 .060” 8054957 SWDR 1-1/2 3/8” Horizontal 4” 1500 .037” 4” 1475 .060” 8137957 SH-DSTR 1 3/8” 17° Angle off Vertical 4” 1500 .035” 4” 1475 .105” 8150922 XP 20 3/8” Vertical 2-1/2” 850 .027” 2” 940 .029” 4” 1475 .105” 8153922 XP 35 3/8” Vertical 3-1/2” 1250 .060” 2” 940 .029” 4” 1475 .105” 8294922 SXP 20 3/8” Vertical or up to 45°2” 750 .027” 2” 635 .029” 8295922 SXP 35 3/8” Vertical or up to 89°3-1/2” 1250 .060” 2” 635 .029” 8293957 SWXP 35 3/8” Horizontal 3-1/2” 1250 .060” SAMMYS® FOR CONCRETE Part No. Model Rod Size Mount Direction UL Max Pipe Size UL Test Load (lbs) UL Min PSI FM Max Pipe Size FM Test Load (lbs) FM Min PSI 8059957 CST 20 3/8” Vertical 4” 1475 3000 8061957 SWC 20 3/8” Horizontal 4” 1475 3000 8150922 XP 20 3/8” Vertical 2-1/2” 850 Pre-Pour Structural @ 3000psi 8150922 XP 20 3/8” Vertical 2-1/2” 850 3) TRUSS-T HANGER® Part No. Model Rod Size Mount Direction UL Load Rating (lbs) UL Test Load (lbs)Listed Application 8296900 HD38TC 3/8” Top Chord 1200 6075 Maximum 4” Schedule 40 pipe 8297900 HD38BC 3/8” Bottom Chord 1200 6075 Maximum 4” Schedule 40 pipe 8198900 HD12CZP 1/2” Bottom Chord 1200 6075 Maximum 8” Schedule 40 Pipe 8298900 HD12TC 1/2” Top Chord 1200 6075 Maximum 8” Schedule 40 Pipe 8299900 HD12BC 1/2” Bottom Chord 1200 6075 Maximum 8” Schedule 40 Pipe APPROVALS APPROVALS APPROVALS APPROVALSPipe Hanger Pipe Hanger Pipe Hanger Pipe Hanger PIPE HANGER *SWG 25-380 Maximum pipe size in composite wood joist allowed by UL is 3-1/2” *SWG 25-380 Maximum pipe size in wood timber or joist allowed by UL is 4” **SWG 20 Maximum pipe size in composite wood joist allowed by UL is 2-1/2”**SWG 20 Maximum pipe size in wood timber or joist allowed by UL is 3” UL compliance with NEC Standards. UL and FM tests were performed in compliance with NFPA 13 Standards. 8022925 SWG 25-380 3/8”Horizontal 3-1/2” - 4”*1500 1-1/2”