Loading...
HomeMy WebLinkAboutA14-0068 DATA SHEETS.pdfModel 5495Distributed Power ModuleThe 5495 is a 6 amp notification powerexpander that provides its own ACpower connection, battery chargingcircuit, and backup battery for use withfire and security controls such as theSilent Knight Model 5208 Fire Control/Communicator. The 5495 is the cost-effective solution for poweringnotification appliances required by theAmericans with Disabilities Act (ADA).The 5495 has built-in ANSI cadencepattern, which can upgrade oldercontrol panels that lack cadencecapability. Features•UL Listed for 6 amps of notificationpower•Power supply’s advanced switchmode design reduces damagingheat and manages power up to 50%more efficiently than other systems•Dip switches allow for easyreconfiguration•24 VDC filtered output voltage•Four power-limited notificationoutputs; 2 Class A or 4 Class B, or 1Class A and 2 Class B•Additional continuous auxiliaryoutput•3 amps per output circuit•2 inputs; 2 Class B or 2 Class A•Ground fault detector/indicator•Independent trouble relay•AC loss delay option shuts off power to non-essential high-currentaccessories like magnetic doorholders•Built-in synchronization forappliances from SystemSensor®,Gentex®, AMSECO®,Wheelock and Faraday•Stand alone operation•Lightweight design adds to ease ofinstallation and reduces shippingcosts•Operates with most polarized, ULListed notification devices•ANSI Cadence pattern outputcapability built-in Connection to Local Fire ControlThe 5495 may be connected to a localfire control which utilizes Class A orClass B type notification circuitsoperating between 9 and 32 VDC. Thecontrol panel’s notification circuit isconnected to one of the inputs on the5495. The control panel’s notificationcircuit end-of-line resistor is alsoconnected across two terminals on the5495, which provides supervisionbetween the 5495 and the fire controlpanel. Polarized audible and/or visualnotification devices are then connectedto the 5495 signal circuits using the4.7kW end-of-line resistors provided.Since the 5495 draws very little powerfrom the control, it is possible toconnect one 5495 to each notificationcircuit on the control panel and stillprovide full supervision of thenotification circuits all the way back tothe control panel. Approvals•UL Listed•MEA 429-92-E Vol XII•CSFM 7300-0559:123•NFPA 72• OSHPD (CA) OSP-0065-10 (see accessories) Model 5495Distributed Power Module The 5495 Distributed Power Module by Silent Knight is the most powerful and cost-effective power supplyavailable today. It delivers 6 amps of notification appliance circuit power and built-in synchronization forappliances from System Sensor®,Gentex®, AMSECO®, Wheelock and Faraday — what you need to drive power-hungry components like ADA notification appliances. The 5495’s advanced microprocessor design is yearsahead of the competition. Its switch mode power supply design is up to 50% more efficient than competitivelinear mode power supplies. And, ADA retrofits are easier and less expensive with the 5495 because itintegrates into current systems without the costly investment in new components.For the most sophisticated and cost-effective notification power supply available, you need the 5495. Call SilentKnight today for more information at 1-800-328-0103. In an emergency,you need maximum power FIRE SYSTEM ACCESSORY Model 5495 Distributed Power Module FIRE SYSTEM ACCESSORY Model 5495Distributed Power Module SupervisionThe 5495 supervises a variety offunctions including:•Low AC power•Low battery condition•Earth ground fault•Auxiliary output power limitcondition•EOL supervision trouble orpower limited condition at anoutputWhen a trouble condition occurs,the 5495 creates a troublecondition on the host control signalcircuits to which it is connected. the5495 still maintains the ability to beactivated by the host control. Inaddition, the 5495 provides a FormC trouble relay output as analternative to using the notificationcircuit trouble.Electrical SpecificationAC input:120 VAC at 2 ampsOutput:24 VDC at 6 amps Current:Standby 75 mAAlarm205 mAAuxiliarypower circuit:1Notificationcircuits:4Outputconfiguration:2 Class A (Style Z)4 Class B (Style Y)(1 Class A & 2 Class B)Amps peroutput circuit:3.0 (6.0 amps total)Notificationcircuit output:20.4 to 27.3 VDC @ 3.0 amps each,4.7 kW EOL resistor requiredon each Class BcircuitNo. of inputs 2Inputconfiguration:2 Class B or 2 Class A Inputvoltage range:9 - 32 VDCBattery chargingcapacity:35.0 AHAmbient temp.:32° to 120° F(0° to 49° C)MechanicalDimensions:12.25” W x 16” H x3” D (30.88 cm Wx 40.64 cm H x7.62 D cm)Indicator LightsAC power on :GreenBattery trouble:YellowGround fault:YellowAux trouble:YellowOutput troubles (1-4):YellowOrdering Information5495 Distributed Power ModuleAccessories:SK-SCK Seismic Compliance Kit MADE IN AMERICA FORM# 350395 Rev F© 2013 Honeywell International Inc. This document is not intended to be used for installation purposes. We try tokeep our product information up-to-date and accurate. We cannot cover allspecific applications or anticipate all requirements. All specifications aresubject to change without notice. For more information, contact Silent Knight12 Clintonville Road, Northford, CT 06472-7161 Phone: (800) 328-0103, Fax: (203) 484-7118.For Technical Support, please call 800-446-6444.www.silentknight.com Agency Listings Features • Plug-in design with minimal intrusion into the back box • Tamper-resistant construction • Automatic selection of 12- or 24-volt operation at 15 and 15/75 candela • Field-selectable candela settings on wall units: 15, 15/75, 30, 75, 95, 110, 115, 135, 150, 177, and 185 • Horn rated at 88+ dBA at 16 volts • Rotary switch for horn tone and three volume selections • Universal mounting plate for wall units • Mounting plate shorting spring checks wiring continuity before device installation • Electrically Compatible with legacy SpectrAlert devices • Compatible with MDL3 sync module • Listed for ceiling or wall mounting The SpectrAlert Advance series offers the most versatile and easy-to-use line of horns, strobes, and horn strobes in the industry. With white and red plastic housings, wall and ceiling mounting options, and plain and FIRE-printed devices, SpectrAlert Advance can meet virtually any application requirement. Like the entire SpectrAlert Advance product line, wall-mount horns, strobes, and horn strobes include a variety of features that increase their application versatility while simplifying installation. All devices feature plug-in designs with minimal intrusion into the back box, making installations fast and foolproof while virtually eliminating costly and time-consuming ground faults. To further simplify installation and protect devices from construction damage, SpectrAlert Advance utilizes a universal mounting plate with an onboard shorting spring, so installers can test wiring continuity before the device is installed. Installers can also easily adapt devices to a suit a wide range of application requirements using field-selectable candela settings, automatic selection of 12- or 24-volt operation, and a rotary switch for horn tones with three volume selections. Indoor Selectable- Output Horns, Strobes, and Horn Strobes for Wall Applications SpectrAlert® Advance audible visible notification products are rich with features guaranteed to cut installation times and maximize profits. MEA452-05-E3023572 7125-1653:186 (indoor strobes) 7125-1653:188 (horn strobes, chime strobes) 7135-1653:189 (horns, chimes) S4011 (chimes, horn strobes, horns)S5512 (strobes) SpectrAlert Advance Specifications Architect/Engineer Specifications General SpectrAlert Advance horns, strobes, and horn strobes shall mount to a standard 4 × 4 × 1½-inch back box, 4-inch octagon back box, or double-gang back box. Two-wire products shall also mount to a single-gang 2 × 4 × 17⁄8-inch back box. A universal mounting plate shall be used for mounting ceiling and wall products. The notification appliance circuit wiring shall terminate at the universal mounting plate. Also, SpectrAlert Advance products, when used with the Sync•Circuit™ Module accessory, shall be powered from a non-coded notification appliance circuit output and shall operate on a nominal 12 or 24 volts. When used with the Sync•Circuit Module, 12-volt-rated notification appliance circuit outputs shall operate between 8.5 and 17.5 volts; 24-volt-rated notification appliance circuit outputs shall operate between 16.5 and 33 volts. Indoor SpectrAlert Advance products shall operate between 32 and 120 degrees Fahrenheit from a regulated DC or full- wave rectified unfiltered power supply. Strobes and horn strobes shall have field-selectable candela settings including 15, 15/75, 30, 75, 95, 110, 115, 135, 150, 177, and 185. Strobe The strobe shall be a System Sensor SpectrAlert Advance Model _______ listed to UL 1971 and shall be approved for fire protective service. The strobe shall be wired as a primary-signaling notification appliance and comply with the Americans with Disabilities Act requirements for visible signaling appliances, flashing at 1 Hz over the strobe’s entire operating voltage range. The strobe light shall consist of a xenon flash tube and associated lens/reflector system. Horn Strobe Combination The horn strobe shall be a System Sensor SpectrAlert Advance Model _______ listed to UL 1971 and UL 464 and shall be approved for fire protective service. The horn strobe shall be wired as a primary-signaling notification appliance and comply with the Americans with Disabilities Act requirements for visible signaling appliances, flashing at 1 Hz over the strobe’s entire operating voltage range. The strobe light shall consist of a xenon flash tube and associated lens/reflector system. The horn shall have three audibility options and an option to switch between a temporal three pattern and a non-temporal (continuous) pattern. These options are set by a multiple position switch. On four-wire products, the strobe shall be powered independently of the sounder. The horn on horn strobe models shall operate on a coded or non-coded power supply. Synchronization Module The module shall be a System Sensor Sync•Circuit model MDL3 listed to UL 464 and shall be approved for fire protective service. The module shall synchronize SpectrAlert strobes at 1 Hz and horns at temporal three. Also, while operating the strobes, the module shall silence the horns on horn strobe models over a single pair of wires. The module shall mount to a 411⁄16 × 411⁄16 × 21⁄8-inch back box. The module shall also control two Style Y (class B) circuits or one Style Z (class A) circuit. The module shall synchronize multiple zones. Daisy chaining two or more synchronization modules together will synchronize all the zones they control. The module shall not operate on a coded power supply. Physical/Electrical Specifications Standard Operating Temperature 32°F to 120°F (0°C to 49°C) Humidity Range 10 to 93% non-condensing Strobe Flash Rate 1 flash per second Nominal Voltage Regulated 12 DC/FWR or regulated 24 DC/FWR1 Operating Voltage Range2 8 to 17.5 V (12 V nominal) or 16 to 33 V (24 V nominal) Operating Voltage Range MDL3 Sync Module 8.5 to 17.5 V (12 V nominal) or 16.5 to 33 V (24 V nominal) Input Terminal Wire Gauge 12 to 18 AWG Wall-Mount Dimensions (including lens)5.6˝ L × 4.7˝ W × 2.5˝ D (142 mm L × 119 mm W × 64 mm D) Horn Dimensions 5.6˝ L × 4.7˝ W × 1.3˝ D (142 mm L × 119 mm W × 33 mm D) Wall-Mount Trim Ring Dimensions (sold as a 5 pack) (TR-HS)5.7˝ L × 4.8˝ W × 0.35˝ D (145 mm L × 122 mm W × 9 mm D) Notes: 1. Full Wave Rectified (FWR) voltage is a non-regulated, time-varying power source that is used on some power supply and panel outputs. 2. P, S, PC, and SC products will operate at 12 V nominal only for 15 and 15/75 cd. Horn and Horn Strobe Output (dBA) Switch Position Sound Pattern dB 8–17.5 Volts 16–33 Volts 24-Volt Nominal Reverberant Anechoic DC FWR DC FWR DC FWR DC FWR 1 Temporal High 78 78 84 84 88 88 99 98 2 Temporal Medium 75 75 80 80 86 86 96 96 3 Temporal Low 71 71 76 76 83 80 94 89 4 Non-Temporal High 82 82 88 88 93 92 100 100 5 Non-Temporal Medium 78 78 85 85 90 90 98 98 6 Non-Temporal Low 73 74 81 81 88 84 96 92 7†Coded High 82 82 88 88 93 92 101 101 8†Coded Medium 78 78 85 85 90 90 97 98 9†Coded Low 74 75 81 81 88 85 96 92 †Settings 7, 8, and 9 are not available on 2-wire horn strobes. UL Max. Strobe Current Draw (mA RMS) Candela 8–17.5 Volts 16–33 Volts DC FWR DC FWR Standard Candela Range 15 123 128 66 71 15/75 142 148 77 81 30 NA NA 94 96 75 NA NA 158 153 95 NA NA 181 176 110 NA NA 202 195 115 NA NA 210 205 High Candela Range 135 NA NA 228 207 150 NA NA 246 220 177 NA NA 281 251 185 NA NA 286 258 UL Max. Current Draw (mA RMS), 2-Wire Horn Strobe, Standard Candela Range (15–115 cd) DC Input 8–17.5 Volts 16–33 Volts 15 15/75 15 15/75 30 75 95 110 115 Temporal High 137 147 79 90 107 176 194 212 218 Temporal Medium 132 144 69 80 97 157 182 201 210 Temporal Low 132 143 66 77 93 154 179 198 207 Non-Temporal High 141 152 91 100 116 176 201 221 229 Non-Temporal Medium 133 145 75 85 102 163 187 207 216 Non-Temporal Low 131 144 68 79 96 156 182 201 210 FWR Input Temporal High 136 155 88 97 112 168 190 210 218 Temporal Medium 129 152 78 88 103 160 184 202 206 Temporal Low 129 151 76 86 101 160 184 194 201 Non-Temporal High 142 161 103 112 126 181 203 221 229 Non-Temporal Medium 134 155 85 95 110 166 189 208 216 Non-Temporal Low 132 154 80 90 105 161 184 202 211 UL Max. Current Draw (mA RMS), 2-Wire Horn Strobe, High Candela Range (135–185 cd) DC Input 16–33 Volts FWR Input 16–33 Volts 135 150 177 185 135 150 177 185 Temporal High 245 259 290 297 Temporal High 215 231 258 265 Temporal Medium 235 253 288 297 Temporal Medium 209 224 250 258 Temporal Low 232 251 282 292 Temporal Low 207 221 248 256 Non-Temporal High 255 270 303 309 Non-Temporal High 233 248 275 281 Non-Temporal Medium 242 259 293 299 Non-Temporal Medium 219 232 262 267 Non-Temporal Low 238 254 291 295 Non-Temporal Low 214 229 256 262 UL Max. Horn Current Draw (mA RMS) Sound Pattern dB 8–17.5 Volts 16–33 Volts DC FWR DC FWR Temporal High 57 55 69 75 Temporal Medium 44 49 58 69 Temporal Low 38 44 44 48 Non-temporal High 57 56 69 75 Non-temporal Medium 42 50 60 69 Non-temporal Low 41 44 50 50 Coded High 57 55 69 75 Coded Medium 44 51 56 69 Coded Low 40 46 52 50 UL Current Draw Data Horn Tones and Sound Output Data 3825 Ohio Avenue • St. Charles, IL 60174 Phone: 800-SENSOR2 • Fax: 630-377-6495 www.systemsensor.com ©2014 System Sensor. Product specifications subject to change without notice. Visit systemsensor.com for current product information, including the latest version of this data sheet. AVDS10201 • 1/14 SpectrAlert Advance Dimensions Model Description Wall Horn Strobes P2R 2-Wire Horn Strobe, Standard cd, Red P2R-P 2-Wire Horn Strobe, Standard cd, Red, Plain P2R-SP 2-Wire Horn Strobe, Standard cd, Red, “FUEGO” P2RH 2-Wire Horn Strobe, High cd, Red P2RH-P 2-Wire Horn Strobe, High cd, Red, Plain P2W 2-Wire Horn Strobe, Standard cd, White P2W-P 2-Wire Horn Strobe, Standard cd, White, Plain P2WH 2-Wire Horn Strobe, High cd, White P2WH-P 2-Wire Horn Strobe, High cd, White, Plain P4R 4-Wire Horn Strobe, Standard cd, Red P4R-P 4-Wire Horn Strobe, Standard cd, Red, Plain P4RH 4-Wire Horn Strobe, High cd, Red P4W 4-Wire Horn Strobe, Standard cd, White Wall Strobes SR Strobe, Standard cd, Red SR-P Strobe, Standard cd, Red, Plain SR-SP Strobe, Standard cd, Red, “FUEGO” SpectrAlert Advance Ordering Information Notes: All -P models have a plain housing (no “FIRE” marking on cover) All -SP models have “FUEGO” marking on cover “Standard cd” refers to strobes that include 15, 15/75, 30, 75, 95, 110, and 115 candela settings. “High cd” refers to strobes that include 135, 150, 177, and 185 candela settings. 4.7˝ 5.6˝ 6.8˝Dia. 2.5˝ 2.5˝ Wall-mount horn strobes Model Description Wall Strobes (cont.) SRH Strobe, High cd, Red SRH-P Strobe, High cd, Red, Plain SRH-SP Strobe, High cd, Red, “FUEGO” SW Strobe, Standard cd, White SW-P Strobe, Standard cd, White, Plain SWH Strobe, High cd, White SWH-P Strobe, High cd, White, Plain Horns HR Horn, Red HW Horn, White Accessories TR-HS Trim Ring, Wall, Red SBBR Indoor Surface Mount Back Box, Red SBBW Indoor Surface Mount Back Box, White DescriptionThe SD500-AIM and SD500-MIM areaddressable input modules for use withthe Intelliknight fire alarm controlpanels (FACPs). The SD500-AIMaddressable input module mounts to a4"-square box. The SD500-MIM miniinput module fits inside a single gangbox. Both input modules are designedto be used with pull stations, water flowswitches, and other applicationsrequiring dry contact alarm initiationdevices. These modules are supervised, singleinput contact monitors. Using an EOLresistor, they monitor for alarm contactclosures and for open circuit wiringfault conditions. If a fault occurs in thewiring, the module alerts the FACP.Each addressable input module isprogrammed with a unique signal linecircuit (SLC) loop address.Features•Single contact monitor•SD500-AIM supports Class A (StyleD) or Class B (Style B) contactmonitor wiring•SD500-MIM support for Class B(Style B) contact monitor wiring•Attractive ivory cover plate with theSD500-AIM•Small and lightweight size allows forflexible mounting options with theSD500-MIM •DIP switch programmable for fastinstallation•Up to 2500 ft wiring distance fromeither input module to contact•Use up to 14 gauge wire•UL listedElectrical SpecificationsStandby Current: 0.55 mAAlarm Current: 23 mA max for onedevice; 46 mA max for two devices;0.55 mA for each additional deviceLine Resistance: 50ž maxMechanical SpecificationsSD500-AIM Physical DescriptionDimensions:4.9" W x 4.9" H x 1" D(12.4 W x 12.4 H x 2.5 D cm)Weight: 3.6 oz (120.1 g)Color: Ivory cover plateSD500-MIM Physical DescriptionDimensions:1.5" W x 2.5" H x 0.7" D(3.8 W x 6.4 H x 1.8 D cm)Weight: 1.6 oz (45.4 g)EnvironmentalOperating Temperature:32ºF – 120ºF (0ºC – 49ºC)Humidity: 10% – 93% non-condensing ApprovalsNFPA 71 & NFPA 72UL 864 CSFM 7300-0559: 132MEA 429-92-E Vol. IXFM Approved for use with the 5820XL SD500-AIM & SD500-MIMAddressable Input Modules The SD500-AIM and SD500-MIM are addressable input modules for use with Silent Knight IntelliKnight firealarm control panels (FACP). The SD500-AIM and SD500-MIM are designed to be used with pull stations, waterflow switches, and other applications requiring dry contact alarm initiation devices. The SD500-AIM addressable input module mounts to a 4"-square box. The SD500-MIM mini input module fitsinside a single gang box. The modules are supervised, single input contact monitors. Using an EOL resister,they monitor for alarm contact closures and for open circuit wiring fault conditions.The SD500-AIM and SD500-MIM offer a compact design for adaptability and pleasing aesthetics as well as easyinstallation and stable operation—a flexible solution for all your fire protection needs.For more information about the IntelliKnight system, or to locate your nearest source, please call 1-800-328-0103. IntelliKnight's addressable contact monitor modules combine fast response with pinpoint location ID. A combination that saves lives and property. INTELLIKNIGHT ACCESSORY INTELLIKNIGHT ACCESSORY MADE IN AMERICAFORM# 350231 Rev. F © 2013 Honeywell International Inc This document is not intended to be used for installation purposes. We try tokeep our product information up-to-date and accurate. We cannot cover allspecific applications or anticipate all requirements. All specifications aresubject to change without notice. For more information, contact Silent Knight12 Clintonville Road, Northford, CT 06472-1610.Phone: (800) 328-0103 Fax: (763) 493-6475 For Technical Support, Please call 800-446-6444..www.silentknight.com Compatible FACPs5820XL5820XL-EVS58085700 Ordering InformationSD500-AIM Input ModuleAddressable input module with ivorycover plate.SD500-MIM Input ModuleAddressable mini input module. SD500-AIM & SD500-MIMAddressable Input Modules Engineering Specifications The contractor shall furnish and install where indicated on the plans, addressable input modules Silent KnightSD500-AIM or SD500-MIM. The modules shall be UL listed and compatible with Silent Knight's IntelliKnightFACPs. The SD500-MIM shall fit inside a single gang electrical box. The SD500-AIM shall be supplied with a plasticcover and shall be suitable for mounting to a 4"-square or double gang electrical box. The SD500-AIMaddressable input module must provide a monitor LED that is visible from outside the cover plate