Loading...
HomeMy WebLinkAboutA15-0002 Data Sheets.pdfDN-6937:D • 12/07/2011 — Page 1 of 2 FAPT-851(A) Acclimate® Plus™ Multi-Sensor Low-Profile Intelligent Detector Intelligent/Addressable Devices DN-6937:D General The Notifier FAPT-851(A) Acclimate® Plus™ detector is anintelligent, addressable, multi-sensing, low-profile detector designed for use with Notifier Notifier Onyx and CLIP series Fire Alarm Control Panels (FACPs). The Acclimate Plus detector uses a combination of photoelec- tric and thermal sensing technologies to increase immunity to false alarms. Unlike traditional intelligent detectors, the Accli- mate Plus detector has a microprocessor in the detector head that processes alarm data. As a result, the Acclimate Plus detector adjusts its sensitivity automatically, without operator intervention or control panel programming. Areas where the Acclimate Plus detector is especially useful include office complexes, schools, college campuses, manu- facturing and industrial facilities, and anywhere else the use ofa particular area may change. The Acclimate Plus detector automatically adjusts its sensitivity to the environment. FlashScan® (U.S. Patent 5,539,389) is a communication pro- tocol developed to greatly enhance the speed of communica- tion between analog intelligent devices and compatible systems. Intelligent devices communicate in a grouped fash- ion. If one of the devices within the group has new information,the panel’s CPU stops the group poll and concentrates on sin- gle points. The net effect is response speed greater than five times that of earlier designs. Features • Automatically adjusts sensitivity levels without operator intervention or programming. Sensitivity increases with heat. • Microprocessor-based, combination photo and thermal technology. • Compatible with all Notifier Onyx and CLIP series Fire Alarm Control Panels (FACPs). • Addressable-analog communication. • Sleek, low-profile design. • Two-wire SLC connection. • Rotary, decimal addressing (1-99 on CLIP systems, 1-159 on FlashScan systems). • Addresses can be viewed and changed without electronic programmers. • Dual bi-color LED design provides 360° viewing angle. • LEDs lock red when in alarm. In FlashScan, LEDs flash green in standby for normal condition. • Built-in tamper-resistant feature. • Constructed of off-white fire-resistant plastic, designed to commercial standards, and offers an attractive appearance. • SEMS screws for wiring of the separate base. • Several base options, including relay, isolator, and sounder. • Built-in functional test switch activated by external magnet. • Listed to UL 268. • Capable of heat-only alarm mode, enabled by a special command from the panel. Smoke alarms are ignored. • Low-temperature signal at 45°F +/– 10°F (7.22°C +/– 5.54°C). Specifications Sensitivity: auto-adjusting levels: 1 to 2%/ft. and 2 to 4%/ft. with classic CLIP systems; 1 to 2, 2 to 3, and 3 to 4%/ft. with systems; fixed-sensitivity levels: 1, 2, and 4%/ft. with classic CLIP systems; 0.5, 1, 2, 3, and 4%/ft. with FlashScan systems. Size: 2.0" (5.3 cm) high; base determines diameter. – B210LP(A): 6.1" (15.5 cm) diameter. – B501(A): 4.1" (10.4 cm) diameter. – B200S(A): 6.875" (17.46 cm) diameter. – B200SR(A): 6.875" (17.46 cm) diameter. – B224RB(A): 6.2" (15.748 cm) diameter. Shipping weight: 5.2 oz. (147 g). Operating temperature: 0°C to 38°C (32°F to 100°F). UL-Listed velocity range: 0 – 4000 ft./min. (1219.2 m/min.), suitable for installation in ducts. Relative humidity: 10% – 93% noncondensing. Thermal sensing rating: fixed-temperature setpoint 135°F (57°C). ELECTRICAL SPECIFICATIONS Voltage range: 15 – 32 volts DC peak. Standby current (max. avg.): 300 μA. Loop resistance: 50 ohms maximum; varies according to control panel used. Refer to panel installation manuals. LED current (max.): 6.5 mA @ 24 VDC (“ON”). Installation The FAPT-851(A) plug-in detector uses a separate base to simplify installation, service, and maintenance. A special tool allows maintenance personnel to plug-in and remove detec- tors without using a ladder. Suitable mounting base boxes include: FAPT-851(A) in B210LP(A) Base FAPT-851 with B210.png Page 2 of 2 — DN-6937:D • 12/07/2011 Notifier®, ONYX®, FlashScan®, and Acclimate® are registered trademarksand Acclimate Plus™ is a trademark of Honeywell International Inc.©2011 by Honeywell International Inc. All rights reserved. Unauthorized useof this document is strictly prohibited. This document is not intended to be used for installation purposes. We try to keep our product information up-to-date and accurate. We cannot cover all specific applications or anticipate all requirements. All specifications are subject to change without notice. For more information, contact Notifier. Phone: (203) 484-7161, FAX: (203) 484-7118. www.notifier.com Made in the U.S. A. • 4.0" (10.16 cm) square box. • 3.5" (8.89 cm) or 4.0" (10.16 cm) octagonal box. • Single-gang box (except relay or isolator base). NOTE: The FAPT-851(A) detector has the unique ability to adjust sensitivity according to the environment, based on heat and smoke levels. Avoid installing these detectors in locations that are susceptible to rapid and high temperature changes. An example of an incorrect application would be near or in line with the output of a self-contained heater. Agency Listings and Approvals These listings and approvals apply to the modules specified in this. In some cases, certain modules or applications may not be listed by certain approval agencies, or listing may be in pro- cess. Consult factory for latest listing status. •UL Listed: S1115. •ULC Listed: S1115. •MEA Listed: 225-02-E. • FM Approved. •CSFM: 7272-0028:0206. •U.S. Coast Guard: 161.002/42/1 (NFS-640); 161.002/50/0 (NFS2-640/NFS-320/NFS-320C, excluding B210LP(A)). •Lloyd’s Register: 11/600013 (NFS2-640, NFS-320/NFS-320C, excluding B210LP(A)). •Maryland State Fire Marshal: Permit # 2122. Ordering Information NOTE: “A” suffix indicates ULC Listed model. FAPT-851: Low-profile intelligent multi-sensor detector. FAPT-851A: Same as FAPT-851 but with ULC Listing. INTELLIGENT BASES NOTE: “A” suffix indicates ULC Listed model. NOTE: For details about intelligent bases and their mounting, see DN-60054. B210LP(A): Plug-in detector base; standard U.S. flanged low- profile mounting base. B210LPBP: Bulk pack of B210LP; package contains 10. B501(A): Flangeless mounting base. B501BP: Bulk pack of B501; package contains 10. B200S(A): Intelligent, programmable sounder base capable of producing sound output in high or low volume with ANSI Tem- poral 3, ANSI Temporal 4, continuous tone, marching tone, and custom tone. B200SR(A): Intelligent sounder base capable of producingsound output with ANSI Temporal 3 or continuous tone. Replaces B501BH series bases in retrofit applications. B224RB(A): Relay base Screw terminals: up to 14 AWG (2.0mm²). Relay type Form-C. Rating: 2.0 A @ 30 VDC resistive; 0.3 A @ 110 VDC inductive; 1.0 A @ 30 VDC inductive. B224BI(A): Isolator base. Maximum: 25 devices between iso- lator bases. ACCESSORIES F110: Retrofit flange to convert B210LP to match the B710LP profile, or to convert older high-profile bases to low-profile. F110BP: Bulk pack of F110; package contains 15. F210: Replacement flange for B210LP(A) base. RA100Z(A): Remote LED annunciator. 3 – 32 VDC. Fits U.S. single-gang electrical box. Supported by B210LP(A) and B501(A) bases only. SMB600: Surface mounting kit for use with B210LP(A). M02-04-00: Test magnet. M02-09-00: Test magnet with telescoping handle. XR2B: Detector removal tool. Allows installation and/or removal of FlashScan® Series detector heads from base in high ceiling installations. T55-127-010: Detector removal tool without pole. XP-4: Extension pole for XR2B. Comes in three 5-foot (1.524 m) sections. DN-7087:C1 • 11/9/11 — Page 1 of 4 SpectrAlert® Advance Selectable Output Notification Appliances Audio/Visual Devices DN-7087:C1 General System Sensor® SpectrAlert® Advance selectable-outputhorns, strobes and horn/strobes are rich with features guaran- teed to cut installation times and maximize profits. The Spec- trAlert Advance series of notification appliances is designed to simplify your installations, with features such as: plug-in designs, instant feedback messages to ensure correct installa- tion of individual devices, and eleven field-selectable candela settings for wall and ceiling strobes and horn/strobes. More specifically, when installing Advance products, first attach a universal mounting plate to a four-inch square, four- inch octagon, or double-gang junction box. The two-wiremounting plate attaches to a single-gang junction box. Then, connect the notification appliance circuit wiring to the SEMS terminals on the mounting plate. Finally, attach the horn, strobe, or horn/strobe to the mounting plate by inserting the product’s tabs in the mounting plate’s grooves. The device will rotate into position, locking the prod- uct’s pins into the mounting plate’s terminals. The device will temporarily hold in place with a catch until it is secured with a captured mounting screw. SpectrAlert Advance products allow you to choose: • 12 or 24 volts. • 15, 15/75, 30, 75, 95, 110, 115, 135, 150, 177, or 185 can- dela by way of a rear-mounted slide switch and front view- ing window. • Horn tones and volume by way of a rotary switch. • The SpectrAlert Advance series includes outdoor notifica- tion appliances. Outdoor strobes and horn/strobes (two- wire and four-wire) are available for wall or ceiling. Outdoorhorns are available for wall only. All System Sensor outdoor products are rated between –40°F and 151°F (–40°C and 66°C) in wet or dry applications. Models available: • Indoor wall-mount: horn, strobe, 2-wire horn/strobe, 4-wire horn/strobe. • Indoor ceiling-mount: strobe, 2-wire horn/strobe, 4-wirehorn/strobe. • Outdoor wall-mount: horn, strobe, 2-wire horn/strobe, 4- wire horn/strobe. • Outdoor ceiling-mount: strobe, 2-wire horn/strobe, 4-wire horn/strobe. Features • Plug-in design. • Same mounting plate for wall- and ceiling-mount units. • Shorting spring on mounting plate for continuity check before installation. • Captive mounting screw. • Tamper-resistance capability. • Field-selectable candela settings on wall and ceiling units: 15, 15/75, 30, 75, 95, 110, 115, 135, 150, 177, 185. • Automatic selection of 12 or 24 volt operation at 15 and 15/ 75 candela. • Outdoor wall and ceiling products. • Outdoor products rated from –40°F and 151°F (–40°C and 66°C). • Outdoor products rainproof per UL50 (NEMA 3R) and weatherproof per NEMA 4X, IP56 • Minimal intrusion into the backbox. • Horn rated at 88+ dbA at 16 volts. • Rotary switch for tone selection. • Three horn volume settings. • Electrically compatible with existing SpectrAlert products. Engineering Specifications SpectrAlert Advance horns, strobes, and horn/strobes shallmount to a standard 4.0" x 4.0" x 1.5" (10.16 x 10.16 x 3.81 cm) backbox, 4.0" (10.16 cm) octagonal backbox, or a double- gang backbox. Two-wire products shall also mount to a single- gang 2.0" x 4.0" x 1.875" (5.08 x 10.16 x 4.763 cm) backbox. A universal mounting plate shall be used for mounting ceiling and wall products. The notification appliance circuit wiring shall terminate at the universal mounting plate. Also, Spec- trAlert Advance products, when used with the Sync•Circuit™ Module accessory, shall be powered from a non-coded notifi- cation appliance circuit output and shall operate on a nominal12 or 24 volts. When used with the Sync•Circuit Module, 12- volt rated notification appliance circuit outputs shall operate between 9 and 17.5 volts; 24-volt rated notification appliance circuit outputs shall operate between 17 and 33 volts. Indoor SpectrAlert Advance products shall operate between 32°F and 120°F (0°C and 49°C) from a regulated DC, or full-wave-recti- fied, unfiltered power supply. Strobes and horn/strobes shallhave field-selectable candela settings including 15, 15/75, 30, 75, 95, 110, 115, 135, 150, 177, 185. Indoor Ceiling Horn/Strobe Outdoor Ceiling Strobe Indoor Wall Horn/Strobe Indoor Ceiling Strobe Indoor WallHorn Outdoor WallStrobe7087pho1.jpg7087pho4.jpg7087pho3.jpg7087pho2.jpg7087pho5.jpg7087pho6.jpg Page 2 of 4 — DN-7087:C1 • 11/9/11 STROBE The strobe shall be a System Sensor SpectrAlert Advance Model _______ listed to UL 1971 and shall be approved for fire protective service. The strobe shall be wired as a primary-sig- naling notification appliance and comply with the Americans with Disabilities Act requirements for visible signaling appli- ances, flashing at 1 Hz over the strobe’s entire operating volt- age range. The strobe light shall consist of a xenon flash tubeand associated lens/reflector system. HORN/STROBE COMBINATION The horn/strobe shall be a System Sensor SpectrAlert Advance Model _______ listed to UL 1971 and UL 464 and shall be approved for fire protective service. The horn/strobe shall be wired as a primary-signaling notification appliance and comply with the Americans with Disabilities Act require- ments for visible signaling appliances, flashing at 1 Hz over the strobe’s entire operating voltage range. The strobe light shall consist of a xenon flash tube and associated lens/reflector sys-tem. The horn shall have three audibility options and an option to switch between a Temporal 3 pattern and a Non-Temporal (continuous) pattern. These options are set by a multiple posi- tion switch. On four-wire products, the strobe shall be powered independently of the sounder. The horn on horn/strobe models shall operate on a coded or non-coded power supply. OUTDOOR PRODUCTS SpectrAlert Advance outdoor horns, strobes and horn/strobes shall be listed for outdoor use by UL and shall operate between –40°F and 151°F (–40°C and 66°C). The productsshall be listed for use with a System Sensor outdoor/weather- proof backbox with half-inch and three-fourths-inch conduit entries. SYNCHRONIZATION MODULE The module shall be a System Sensor Sync•Circuit MDL3R or MDL3W listed to UL 464 and shall be approved for fire protec- tive service. The module shall synchronize SpectrAlert strobesat 1 Hz and horns at Temporal 3. Also, while operating the strobes, the module shall silence the horns on horn/strobe models over a single pair of wires. The module shall mount to a 4.688" x 4.688" x 2.125" (11.906 x 11.906 x 5.398 cm) back- box. The module shall also control two Style Y (class B) cir- cuits or one Style Z (Class A) circuit. The module shall synchronize multiple zones. Daisy-chaining two or more syn- chronization modules together will synchronize all the zones they control. The module shall not operate on a coded power supply. Operating Specifications •Standard operating temperature: 32°F to 120°F (0°C to 49°C). •K Series operating temperature: –40°F to 151°F (–40°C to 66°C). •Humidity range: 10% to 93% non-condensing (indoor products). •Strobe flash rate: 1 flash per second. •Nominal voltage: regulated 12 VDC/FWR or regulated 24 VDC/FWR. NOTE: Full Wave Rectified (FWR) voltage is a non-regulated, time-varying power source that is used on some power supply and panel outputs. •Operating voltage range: 8 V to 17.5 V (12 V nominal); or16 V to 33 V (24 V nominal). NOTE: P, S, PC, and SC prod- ucts will operate at 12 V nominal only for 15 cd and 15/75 cd. •Input terminal wire gauge: 12 to 18 AWG (3.31 to 0.821 mm²). •Ceiling-mount dimensions (including lens): 6.8" diame- ter x 2.5" deep (17.3 cm diameter x 6.4 cm deep). •Wall-mount dimensions (including lens): 5.6" H x 4.7" Wx 2.5" D (14.2 cm H x 11.9 cm W x 6.4 cm D). •Horn dimensions: 5.6" H x 4.7" W x 1.3" D (14.2 cm H x11.9 cm W x 3.3 cm D). Agency Listings and Approvals The listings and approvals below apply to SpectrAlert Advance Selectable Output Notification Devices. In some cases, certain modules may not be listed by certain approval agencies, or listing may be in process. Consult factory for latest listing sta- tus. •UL Listed: S4011 (HR__, HW__, P2__, P4__, PC2__, PC4__ models); S5512 (models SCR, SCRH, SCW, SCWH, SR, SRH, SW, SWH); S3593 (SCRHK, SCRK, SRHK, SRK). •ULC Listed: S4011 (HRA, HRKA); S5512 (typically “A” models, with exception of outdoor strobes). See Canadian data sheet for listings and specifications. •FM approved •MEA: 452-05-E •CSFM: 7125-1653:0186 (SCR, SCRH, SCW, SCWH, SR, SRH, SW, SWH); 7300-1653:0188 (P2_, P4_, PC2_, PC4_ modules); 7135-1653:0189 (HR, HRK, HW); 7300- 1653:0187 (SCRHK, SCRK, SRHK, SRK). Strobe Current Draw, UL Maximum (mA RMS) Candela 8 – 17.5 V 16 – 33 V DC FWR DC FWR Standard Candela Range 15 123 128 66 71 15/75 142 148 77 81 30 NA N/A 94 96 75 NA NA 158 153 95 NA NA 181 176 110 NA NA 202 195 115 NA NA 210 205 High Candela Range 135 NA NA 228 207 150 NA NA 246 220 177 NA NA 281 251 185 NA NA 286 258 Horn Current Draw, UL Maximum (mA RMS) Sound Pattern dB 8 – 17.5 V 16 – 33 V DC FWR DC FWR Temporal High 57 55 69 75 Temporal Medium 44 49 58 69 Temporal Low 38 44 44 48 Non-temporal High 57 56 69 75 Non-temporal Medium 42 50 60 69 Non-temporal Low 41 44 50 50 Coded High 57 55 69 75 Coded Medium 44 51 56 69 Coded Low 40 46 52 50 DN-7087:C1 • 11/9/11 — Page 3 of 4 Two-Wire Horn/Strobe, STANDARD Candela Range (15 – 115 cd), UL Maximum Current Draw (mA RMS) Input, Sound Pattern, dB Level 8 – 17.5 V 16 – 33 V 15 15/75 15 15/75 30 75 95 110 115 DC Input, Temporal, High 137 147 79 90 107 176 194 212 218 DC Input, Temporal, Medium 132 144 69 80 97 157 182 201 210 DC Input, Temporal, Low 132 143 66 77 93 154 179 198 207 DC Input, Non-temporal, High 141 152 91 100 116 176 201 221 229 DC Input, Non-temporal, Medium 133 145 75 85 102 163 187 207 216 DC Input, Non-temporal, Low 131 144 68 79 96 156 182 201 210 FWR Input, Temporal, High 136 155 88 97 112 168 190 210 218 FWR Input, Temporal, Medium 129 152 78 88 103 160 184 202 206 FWR Input, Temporal, Low 129 151 76 86 101 160 184 194 201 FWR Input, Non-temporal, High 142 161 103 112 126 181 203 221 229 FWR Input, Non-temporal, Medium 134 155 85 95 110 166 189 208 216 FWR Input, Non-temporal, Low 132 154 80 90 105 161 184 202 211 Two-Wire Horn/Strobe, HIGH Candela Range (135 – 185 cd), UL Maximum Current Draw (mA RMS) DC Input 16 – 33 V FWR Input 16 – 33 V 135 150 177 185 135 150 177 185 DC, Temporal, High 245 259 290 297 FWR, Temporal, High 215 231 258 265 DC, Temporal, Medium 235 253 288 297 FWR, Temporal, Medium 209 224 250 258 DC, Temporal, Low 232 251 282 292 FWR, Temporal, Low 207 221 248 256 DC, Non-temporal, High 255 270 303 309 FWR, Non-temporal, High 233 248 275 281 DC, Non-temporal, Medium 242 259 293 299 FWR, Non-temporal, Medium 219 232 262 267 DC, Non-temporal, Low 238 254 291 295 FWR, Non-temporal, Low 214 229 256 262 7087dim12009.tif 2.5 2.5” 4.7” 5.6” 6.8” Horn and Horn/Strobe Output (dBA) SwitchPosition Sound Pattern dB 8 – 17.5 V 16 – 33 V DC FWR DC FWR 1 Temporal High 78 78 84 84 2 Temporal Medium 74 74 80 80 3 Temporal Low 71 73 76 76 4 Non-temporal High 82 82 88 88 5 Non-temporal Medium 78 78 85 85 6 Non-temporal Low 75 75 81 81 7* Coded High 82 82 88 88 8* Coded Medium 78 78 85 85 9* Coded Low 75 75 81 81 *NOTE: Settings 7, 8, and 9 are not available on 2-wire horn/strobe. Horn and Horn/Strobe Rotary Switch Setting Setting Repetition Rate dB Level 1 Temporal horn High 2 Temporal horn Medium 3 Temporal horn Low 4 Normal horn High 5 Normal horn Medium 6 Normal horn Low 7* Externally coded High 8* Externally coded Medium 9* Externally coded Low *NOTE: Settings 7, 8, and 9 are not available on 2-wire horn/strobe. Page 4 of 4 — DN-7087:C1 • 11/9/11 Sync•Circuit™ is a trademark and NOTIFIER® and SpectrAlert® areregistered trademarks of Honeywell International Inc. ©2011 by Honeywell International Inc. All rights reserved. Unauthorized useof this document is strictly prohibited. This document is not intended to be used for installation purposes. We try to keep our product information up-to-date and accurate. We cannot cover all specific applications or anticipate all requirements. All specifications are subject to change without notice. For more information, contact Notifier. Phone: (203) 484-7161, FAX: (203) 484-7118. www.notifier.com Ordering Information Model Description Model Description WALL HORN/STROBES CEILING HORN/STROBES P2R 2-wire horn/strobe, standard cd, red.PC2R 2-wire horn/strobe, standard cd, red. P2RH 2-wire horn/strobe, high cd, red.PC2RH 2-wire horn/strobe, high cd, red. P2RK 2-wire horn/strobe, standard cd, red, outdoor.PC2RK 2-wire horn/strobe, standard cd, red, outdoor. P2RHK 2-wire horn/strobe, high cd, red, outdoor.PC2RHK 2-wire horn/strobe, high cd, red, outdoor. P2W 2-wire horn/strobe, standard cd, white.PC2W 2-wire horn/strobe, standard cd, white. P2WH 2-wire horn/strobe, high cd, white.PC2WH 2-wire horn/strobe, high cd, white. P4R 4-wire horn/strobe, standard cd, red.PC4R 4-wire horn/strobe, standard cd, red. P4RH 4-wire horn/strobe, high cd, red.PC4RH 4-wire horn/strobe, high cd, red. P4RK 4-wire horn/strobe, standard cd, red, outdoor.PC4RK 4-wire horn/strobe, standard cd, red, outdoor. P4RHK 4-wire horn/strobe, high cd, red, outdoor.PC4RHK 4-wire horn/strobe, high cd, red, outdoor. P4W 4-wire horn/strobe, standard cd, white.PC4W 4-wire horn/strobe, standard cd, white. P4WH 4-wire horn/strobe, high cd, white.PC4WH 4-wire horn/strobe, high cd, white. WALL STROBES CEILING STROBES SR Strobe, standard cd, red.SCR Strobe, standard cd, red. SRH Strobe, high cd, red.SCRH Strobe, high cd, red. SRK Strobe, standard cd, red, outdoor.SCRK Strobe, standard cd, red, outdoor. SRHK Strobe, high cd, red, outdoor.SCRHK Strobe, high cd, red, outdoor. SW Strobe, standard cd, white.SCW Strobe, standard cd, white. SWH Strobe, high cd, white.SCWH Strobe, high cd, white. ACCESSORIES HORNS BBS-2A Backbox skirt, wall, red.HR Horn, red. BBSW-2A Backbox skirt, wall, white.HRK Horn, red, outdoor. BBSC-2A Backbox skirt, ceiling, red.HW Horn, white. BBSCW-2A Backbox skirt, ceiling, white. ACCESSORIES, continued SA-WBB Weatherproof backbox, wall.TR-HS Trim Ring, wall, red, package of 5 SA-WBBC Weatherproof backbox, ceiling. TRW-HS Trim Ring, wall, white, package of 5 WTP Weatherproof, flush mount plate, red TRC-HS Trim Ring, ceiling, red, package of 5 WTPW Weatherproof, flush mount plate, white TRCW-HS Trim Ring, ceiling, white, package of 5 NOTE: “High cd” refers to strobes that include 135, 150, 177, and 185 candela settings. “Standard cd” refers to strobes that include 15, 15/75, 30, 75, 95, 110, and 115 candela settings. NOTE: For strobes and horn/strobes, add suffix “F” for French or “B” for Bilingual. NOTE: All outdoor models (“K(A)” suffix) include a plastic weatherproof backbox. NOTE: Add “-R” to models for weatherproof replacement device (no back box included). Only for use with weatherproof outdoor flush mounting plate, WTP and WTPW. NOTE: Add “P” to model for plain housing. (No “FIRE” marking on cover.)