Loading...
HomeMy WebLinkAboutPID-95.pdfGAMEWELL-FCI12 Clintonville Road, Northford, CT 06472-1610 USA • Tel: (203) 484-7161 • Fax: (203) 484-7118Specifications are for information only, are not intended for installation purposes, and are subject to change without notice. No responsibility is assumed by Gamewell-FCI for their use. ©2008 by Honeywell International Inc. All rights reserved.www.gamewell-fci.com CS-2044 Rev. B page 1 of 2 PID-95P, PID-95 Point Identification Device APPROVED MEA Approved An ISO 9000-2000 Company 7300-1703:135 SIGNALING S521 FM Description The Gamewell-FCI PID-95P addressable point identifica- tion device is the interface between the non-powered, nor- mally open, dry-contact devices and Gamewell-FCI’s 600 Series and ILI95-E3 Series® of analog addressable Fire Alarm Control Panels (FACPs). Point identification devices monitor a single Style B circuit, and are designed for con- cealed mounting in an electrical backbox. The PID-95P can be surface or flush mounted and has a visible LED for alarm/annunciation. Operation The point identification device connects to the Signaling Line Circuit (SLC) via two wires. The PID-95 will monitor, via a two-wire supervised SLC circuit, contact-type devices such as a waterflow switch or a manual station. Upon acti- vation of the monitored device, the PID-95 will report its address to the 600 Series and ILI95-E3 Series FACP via the analog SLC. The control panel will then activate into all alarm programmed outputs related to the PID-95. Programming The PID-95 is programmed by setting a single DIP switch, easily accessible on the device’s printed circuit board. The DIP switch sets the address of the device and the priority interrupt (DIP SW #8). All other programming is accom- plished at the FACP through a laptop computer or the con- trol panel operator’s display. (600 Series only). Standard Application The PID-95 is the interface between the dry-contact type devices and the SLC of the control panel. The PID-95 is a means of connecting and identifying monitor points without the use of conventional input modules at the main control panel. The use of PID-95s can dramatically reduce the field wiring required on many projects. E3 Series® is a registered trademark of Honeywell International Inc. Microsoft® Windows® is a registered trademark of Microsoft® Corporation. Features • Compatible with the Gamewell-FCI, 600 Series and ILI95-E3 Series Systems • Monitors dry-contact devices • LED for alarm annunciation • Field programmable • Priority interrupt • Plate-mounted version available for surface or flush mounting in a 4" x 4.688" (10.16 cm x 11.908 cm) double gang backbox or 4” x (10.16 cm) square backbox PID-95PID-95P GAMEWELL-FCI 12 Clintonville Road, Northford, CT 06472-1610 USA • Tel: (203) 484-7161 • Fax: (203) 484-7118CS-2044 Rev. B page 2 of 2 www.gamewell-fci.com Engineer’s Specifications Addressable interface devices shall be provided for the monitoring and supervision of contact type devices con- nected to the Fire Alarm Control Panel. The devices shall monitor a normally open dry contact. The addressable interface devices shall communicate to the main control panel via the analog addressable circuit. The interface device shall be Gamewell-FCI PID-95P or PID-95. Specifications PID-95P Standby Current:0.0005A, 0.0008A Alarm Current:0.0015A Operating Temperature:32°F to 120°F (0°C to 49°C) Relative Humidity:93%, non-condensing Dimensions:4" x 4.688" (10.16 cm x 11.908 cm), double gang backbox PID-95 Standby Current:0.0005A, 0.0008 A Alarm Current:0.0015A Operating Temperature:32°F to 120°F (0°C to 49°C) Relative Humidity:93%, non-condensing Dimensions:4" (10.16 cm) square backbox with blank cover plate Ordering Information Part NumberDescription PID-95 Addressable point identification device for monitoring contact devices PID-95P Addressable input interface device mounted on 4.688" (11.908 cm) plastic plate 70839 Trim ring for flush-mounting on the PID-95P