Loading...
The URL can be used to link to this page
Your browser does not support the video tag.
Home
My WebLink
About
A17-0045_Silent Knight SK-Fire-CO_1506353220.pdf
The SK-FIRE-CO is a plug-in, addressable device that provides both fire and carbon monoxide (CO) detection. For fire, the detector combines four separate sensing elements in one unit (smoke, CO, light/flame, and heat) to sense multiple components of a fire. This approach enables enhanced sensitivity to real fire with heightened immunity to nuisance particulate. For CO, the detector’s electrochemical sensing cell creates a separate signal for life safety CO detection. Released through the incomplete burning of various fuels, CO is a colorless, odorless and deadly gas that is virtually impossible to detect with the human senses. Because the potential exists for dangerous levels of CO to accumulate in almost any building, legislation mandating the use of CO detection in commercial spaces continues to increase across the U.S. and Canada. The SK-FIRE-CO is listed to the UL 2075 standard for system-connected life safety carbon monoxide monitoring. The SK-FIRE-CO should be used in conjunction with the B200S intelligent sounder base (sold separately), which can generate either a Temp 3 pattern for fire or a Temp 4 pattern for CO alarm indication. With each sounder base learning the address of the detector connected, the FACP can then command an individual sounder, or a group of sounders, to activate. The command set from the panel can be tailored to the specific event, allowing selection of tone, and group. For more information on the B200S refer to Data Sheet P/N 351183. SK-FIRE-CO can also be used with the B210LP 6” standard base, the B200SR sounder base or the B224RB relay base. +,)* • Unique ability to detect all four major elements of a fire: - Smoke - Carbon Monoxide (CO) - Light/flame - Heat • Separate CO detection signal • Highest nuisance alarm immunity • Automatic drift compensation of smoke sensor and CO cell • Uses only one address on the SLC SK-FIRE-CO offers world-class fire and carbon monoxide (CO) detection combined in a single addressable device to provide a practical and cost-effective solution for today’s market. For more information about the SK-FIRE-CO, or to locate you nearest source, please call 800-328-0103. -& ,$+")"+)" ") ++') INTELLIKNIGHT ACCESSORY • RealTest® CO testing capability • UL 268 and UL 2075 listed • Separates audible signal for fire or CO alarm when used with the B200S base • CO cell end-of-life warning and fault '%(+""$"+/ The SK-FIRE-CO is compatible with the following IntelliKnight FACP’s programmed for System Sensor protocol: (Firmware version 13.0 or higher). • 5700 • 5808 • 5820XL • 5820XL-EVS "&*+$$ "& ',&) * *'$ *()+$/ Vail Fire & Emergency Services 09/25/17 '$ ,$+")"+)" ++') FORM# 351181 Rev C © 2013 Honeywell International Inc. This document is not intended to be used for installation purposes. We try to keep our product information up-to-date and accurate. We cannot cover all specific applications or anticipate all requirements. All specifications are subject to change without notice. For more information, contact Silent Knight 12 Clintonville Road, Northford, CT 06472-1610 Phone: (800) 328-0103, Fax: (203) 484-7118. For Technical Support, Please call 800-446-6444. ...*"$&+#&"߰!+'% (""+"'&* !/*"$ Diameter: 6.875” (17.46 cm) installed in a B200S base Height: 3.46” (8.79 cm) installed in B200S base Shipping Weight: 4.6 oz Color: Ivory ()+"&߰ Temperature Range: 32° F to 100° F (0° C to 38° C) Humidity: 15 to 90% relative humidity (non-condensing) Air Velocity: 0 to 4,000 ft/min (0 to 20 m/sec) $+)"$ Operating Voltage: 15 to 32 VDC Maximum Standby: 300µA at 24 VDC (no communication every 5 seconds with LED blink enabled) Maximum Alarm Current (LED on): 7.2 mA at 24 VDC '&"+')"&߰ +&) )& $)% !)*!'$* ) * '$$'.* Note: Per UL Standard 2075, the SK-FIRE-CO has been tested to the sensitivity limits defined in UL Standard 2034. ))"&߰ &')%+"'& SK-FIRE-CO Multi-Criteria CO Detector (base not included) (+"'&$ **')"* B200S Intelligent sounder base B210LP 6” mounting base B200SR Sounder base B224RB Relay base M02-04-01 Detector test magnet M02-09-01 Telescoping test magnet )+* ) "$$"'& ++') *('&* "% 70 ± 5 ppm 60-240 min. 150 ± 5 ppm 10-50 min. 400 ± 10 ppm 4-15 min. Vail Fire & Emergency Services 09/25/17