The URL can be used to link to this page

Home My WebLink AboutB15-0031 E-101.pdfPROPERTY LINE PROPERTY LINE PROPERTY LINE PROPERTY LINE PROPERTY LINE PROPERTY LINE PROPERTY LINE PROPERTY LINE PROPERTY LINE 225A3P EXISTING 3000 AMP SWITCHBOARD "DP-DA2" 208/120V., 3ɐ, 4 WIRE. 42,000 AIC "PP-P5A" SEC. 1 LOCATED IN 5TH FLOOR ELEC. ROOM (FED FROM "DP-DA2" CCT #8) "PP-P5A" SEC. 2 NOTES TO ELECTRICAL CONTRACTOR - PANEL: 1. INFORMATION SHOWN IN BOLD PRINT INDICATES NEW LOADS ON EXISTING UNLESS OTHERWISE NOTED. ALL OTHER LOADS ARE EXISTING. 2. UPDATE PANEL INDEXES PRIOR TO CONCLUSION OF CONSTRUCTION PER NEC 408.4. INDICATE LOAD INFORMATION AND ACCURATE LOCATION WITHIN TENANT SUITE. 3. VERIFY BREAKERS FOR ALL MECHANICAL REQUIREMENTS WITH MANUFACTURER'S U.L. NAMEPLATE RATING AND CUTSHEETS PRIOR TO ROUGH-IN. CONTACT ELECTRICAL AND MECHANICAL ENGINEERS IF ANY DISCREPANCIES OR CHANGES TO THE SPECIFIED UNITS OCCUR. 1. BASE BUILDING SPECIFICATIONS, DRAWINGS, AND LATEST REVISION OF CONTRACT DOCUMENTS FOR ELECTRICAL WORK SHALL APPLY TO ELECTRICAL DRAWINGS. 2. ALL WORK SHALL BE DONE IN COMPLIANCE WITH THE TENANT FINISH SPECIFICATIONS, DRAWINGS, AND LATEST REVISIONS OF ALL NATIONAL CODES SUCH AS THE N.E.C., N.F.P.A., AND ALL APPLICABLE LOCAL CODES AND ORDINANCES. 3. ELECTRICAL CONTRACTOR SHALL VISIT SITE AND EXAMINE DRAWINGS OF OTHER TRADES ON THIS PROJECT, PARTICULARLY DEMOLITION, ARCHITECTURAL AND MECHANICAL, TO DETERMINE ANY ADDITIONAL WORK THAT MAY BE REQUIRED FOR A COMPLETE AND OPERATIONAL ELECTRICAL INSTALLATION. 4. ELECTRICAL ITEMS AFFECTED BY REMODEL WORK ARE SHOWN ON DRAWINGS. EXISTING ELECTRICAL SHOWN IS NOT NECESSARILY INCLUSIVE. PROVIDE CONTINUITY IN ALL CIRCUITS FOR ELECTRICAL FIXTURES, DEVICES, AND EQUIPMENT THAT IS TO REMAIN. SUCH EQUIPMENT SHALL BE RECONNECTED TO EXISTING CIRCUITS. 5. ELECTRICAL CONTRACTOR SHALL ENSURE CIRCUIT CONTINUITY FOR ALL CIRCUITS WHICH ARE OR MAY BE AFFECTED BY THIS REMODEL AS WELL AS TO PREVENT ANY SINGLE CIRCUIT OVER-LOADING. REMOVE ALL EXISTING BRANCH CIRCUIT CONDUCTORS OF CIRCUITS REUSED ELSEWHERE. 6. CONTRACTOR SHALL PROVIDE NEW CONDUIT AND WIRE TO REROUTE AND RECONNECT FEEDERS THAT ARE DAMAGED, DISTURBED OR AFFECTED BY THE DEMOLITION AND REMODEL WORK. 7. CONTRACTOR SHALL BE HELD RESPONSIBLE FOR VERIFICATION OF EXISTING JOB CONDITIONS PRIOR TO BID. DISCREPANCIES BETWEEN ACTUAL FIELD CONDITIONS AND CONTRACT DOCUMENTS SHALL BE BROUGHT TO THE ENGINEER'S ATTENTION FOR ALTERNATIVE METHODS OF INSTALLATION THREE (3) DAYS MINIMUM PRIOR TO BIDDING THIS JOB TO ALLOW FOR ISSUANCE OF CLARIFICATIONS. 8. CONTRACTOR TO REMOVE ALL FIXTURES, SWITCHES, TELEPHONE AND ELECTRICAL OUTLETS SCHEDULED FOR DEMOLITION. ALL UNUSED POWER WIRING SHALL BE REMOVED BACK TO APPROPRIATE ELECTRICAL PANEL. ALL PHONE / DATA CABLING TO REMAIN - FOR REMOVAL PER TENANT COMMUNICATION VENDOR. 9. PROVIDE TYPEWRITTEN UPDATED PANEL DOOR DIRECTORIES FOR ALL AFFECTED PANELS REFLECTING ALL CIRCUITS WITH THEIR ACCURATE DESTINATIONS PER N.E.C. 408.4. CLEARLY MARK J-BOXES IN CEILING SPACE WITH REVISED CIRCUIT NUMBERS. THIS APPLIES TO BOTH SIDES OF THE TENANT DEMISING WALLS. FLIP ALL UNUSED AND SPARE BREAKERS TO THE "OFF" POSITION AND INDICATE "SPARE" IN PANEL INDEX. 10. PREPARE AND MAINTAIN AT JOB SITE ACCURATE UPDATED "AS-BUILT" DRAWINGS OF ALL MODIFIED WORK IN THIS CONTRACT. AT CONCLUSION OF WORK, SUBMIT ORIGINAL OR ADEQUATE LEGIBLE REPRODUCIBLE COPY TO ARCHITECT / ENGINEER FOR PREPARATION OF RECORD DOCUMENTS. 11. ALL ELECTRICAL DEVICES, CIRCUITING, ETC. SHOWN DIAGRAMMATICALLY. ELECTRICAL CONTRACTOR SHALL BE RESPONSIBLE FOR ACTUAL LOCATION AND WIRING AVOIDING MECHANICAL AND OTHER EQUIPMENT. 12. ALL NEW AND RELOCATED MATERIALS INSTALLED IN CEILING PLENUM SHALL BE U.L. LISTING, CLASS 1 RATED. 13. SEE LEGEND, LIGHTING AND POWER NOTES, MECHANICAL, AND ARCHITECTURAL DRAWINGS FOR SUPPLEMENTAL INFORMATION ON LOCATIONS, MOUNTING HEIGHTS, ETC. DIMENSIONS ON ARCHITECTURAL DRAWINGS TAKE PRECEDENCE OVER THE ELECTRICAL DRAWINGS. 14. PROVIDE TELEPHONE OUTLETS WITH COVERPLATES AND 3 4 " CONDUIT TO ABOVE ACCESSIBLE CEILING WITH BUSHING AND PULLWIRE. COORDINATE FURNITURE SYSTEM CONDUIT WITH MANUFACTURER / SUPPLIER ON ALL DATA / TELEPHONE RACEWAYS. CABLING BY TENANT. 15. COORDINATE ALL POWER SHUT-DOWNS WITH BUILDING MANAGEMENT / LANDLORD. 16. CLEAN AND REPAIR ALL EXISTING LIGHTING FIXTURES, RECEPTACLES, AND ELECTRICAL DEVICES AS NEEDED. 17. REUSE EXISTING EXIT LIGHTS. VERIFY EXISTING FIXTURE COUNT WITH ARCHITECT. PROVIDE UNIT PRICING FOR ADDITIONAL FIXTURES AS NEEDED - BUILDING STANDARD. 18. RESUPPORT ALL NEW AND EXISTING CONDUITS, LIGHTING FIXTURES, AND CABLING PER INTERNATIONAL BUILDING CODE (IBC 2009). REMOVE ALL UNUSED SUPPORTS AS REQUIRED. 19. ELECTRICAL CONTRACTOR TO CIRCUIT TRACE ALL POWER CIRCUITRY PRIOR TO INSTALLATION. CONTRACTOR TO PROVIDE ELECTRICAL ENGINEER WITH AS-BUILT DRAWINGS. 20. DO NOT SCALE DRAWINGS. ELECTRICAL CONTRACTOR SHALL FIELD VERIFY ALL DIMENSIONS, DISTANCES, AND EXISTING CONDITIONS PRIOR TO PRICING AND INSTALLATIONS. 21. ELECTRICAL CONTRACTOR SHALL SUBMIT CUT-SHEETS AND SHOP DRAWINGS ON ALL ELECTRICAL AND MECHANICAL EQUIPMENT FOR APPROVALS. SUBMIT TO GENERAL CONTRACTOR, OWNER, TENANT, ARCHITECT, AND ENGINEERS. 22. E.C. SHALL LABEL ALL RECEPTACLE COVER PLATES WITH PANEL AND CIRCUITRY DESIGNATIONS. DESIGN BUILD FIRE ALARM NOTE: FIRE ALARM SHALL BE UNDER DESIGN BUILD CONTRACT. FIRE ALARM CONTRACTOR SHALL BE BUILDING MANAGEMENT APPROVED AND WILL SUBMIT FIRE ALARM DESIGN TO THE FIRE MARSHAL OF THE LOCAL FIRE DEPARTMENT HAVING JURISDICTION FOR APPROVAL. ELECTRICAL GENERAL NOTES: CONTRACTOR IS TO FIELD VERIFY ALL DIMENSIONS. WRITTEN DIMENSIONS HAVE PRECEDENCE OVER SCALED DIMENSIONS. THE CONTRACTOR SHALL VERIFY AND BE RESPONSIBLE FOR ALL DIMENSIONS AND CONDITIONS ON THE JOB AND ARCHITECT MUST BE NOTIFIED OF ANY VARIATIONS FROM THE DIMENSIONS AND CONDITIONS SHOWN ON THESE DRAWINGS. ALL CEILING LOCATED ITEMS MUST BE COORDINATED WITH ARCHITECT. LOCATIONS OF LIGHTING EQUIPMENT TAKE PRECEDENCE. ELECTRICAL CONTRACTOR MUST ADHERE TO ALL NATIONAL AND LOCAL ELECTRICAL CODES. IT IS THE RESPONSIBILITY OF THE ELECTRICAL CONTRACTOR TO NOTIFY ARCHITECT IF ANY LOCAL CODE CONFLICT EXISTS. ANY REVISIONS TO THIS PLAN CAUSED BY MECHANICAL OR STRUCTURAL CONFLICTS MUST BE APPROVED IN WRITING. FIXTURE SUBSTITUTIONS ARE NOT ALLOWED UNLESS APPROVED IN WRITING BY ARCHITECT. 1. ALL SYMBOLS MAY NOT BE USED. 2. ALL LAMPS THAT TIE INTO THE SPECIAL DIMMED RECEPTACLES WILL REQUIRE PLUG #RP-FDU-10(WHITE OR BROWN). THIS WORKS IN CONJUNCTION WITH THE SPECIFIED RECEPTACLE LISTED ABOVE. PLEASE CONTACT TAMMY WINGATE AT LUTRON, 610.282.6539, FOR PURCHASING INFORMATION. 3. FLOOR RECEPTACLES MUST BE INSTALLED IN CARLON FLOOR BOX #E976RFB WITH AN ACTIVATION KIT #E97AK2. INCLUDE COVER FINISH/COLOR. ALL LAMPS THAT TIE INTO THE SPECIAL DIMMED RECEPTACLES WILL REQUIRE PLUG #RP-FDU-10. THIS WORKS IN CONJUNCTION WITH THE SPECIFIED RECEPTACLE LISTED ABOVE. THIS COMBINATION IS REQUIRED TO MEET THE NATIONAL ELECTRIC CODE (NEC). CONTACT TAMMY WINGATE AT LUTRON, 610.282.6539, FOR PURCHASING INFORMATION. GENERAL NOTES - POWER: NOTES TO CONTRACTOR: ISSUE DATE JMM CHK BY: SCALE: SHEET: JOB #: DRW BY: TITLE: DATE: COMMENT AS NOTED TNS SEAL & SIGNATURE: 14-37 1 FOUR SEASONS RESORT & RESIDENCES VAIL, CO FIFTH FLOOR REMODEL FOR PERMIT 2/16/15 CLIENT: Four Seasons Resort & Residences One Vail Road VAIL, CO 81657 ARCHITECT: Creative Design Associates 434 BROADWAY, 5TH FLOOR NEW YORK, NY 10013 t 212-748-8900 WESTERN US 4700 E BROMLEY LN, SUITE 105 BRIGHTON, CO 80601 t 646-747-2171 c 917-756-0057 dsorenson@ralcompanies.com INTERIOR DESIGN: Meyer Davis Studio 180 VARICK STREET #404 NEW YORK, NY 10014 t 212-627-5574 graydavis@meyerdavis.com ELECTRICAL ENGINEER: C3S Incorporated 3212 WEST 45TH AVENUE DENVER, CO 80211 t 303-480-5144 theresa@c3sengineeringinc.com MECHANICAL ENGINEER: MDP Engineering Group 1800 Glenarm Place, Suite 800 DENVER, CO 80202 t 303-389-0095 rloomer@mdpeg.com LIGHTING DESIGN: Bouyea & Associates 5 Green Hill Road 2nd & 3rd Floors Washington Depot, CT 06794 t 860-868-4500 bbouyea@bouyea.com FOODSERVICE CONSULTANT: Ricca Design Studios 2 Northside Piers, Suite 8C Brooklyn, NY 11249 t 303-221-0500 dchislett@ricca.com 2/16/215 NOTES, PANEL SCHEDULES, & ONE LINE DIAGRAM E-101 5TH FLOOR LOBBY AREA KEY PLAN 1 C3S Incorporated EXISTING PARTIAL ONE LINE DIAGRAM 3 ALL DASHED LINES INDICATE EXISTING TO REMAIN U.O.N. ALL SOLID LINES INDICATE NEW EQUIPMENT ALL HIDDEN LINES INDICATE FUTURE EQUIPMENT. ALL SHADED AREAS INDICATE EXISTING TO BE REMOVED. 1 E-201 1 E-301 1 E-501 1 E-401 5TH FLOOR LOBBY AREA DRAWING KEY PLAN 2 C3S Incorporated 03/17/15