Loading...
HomeMy WebLinkAboutB18-0139_REV1 approved documents_1539029332.pdf75 South Frontage Road West, Vail, CO 81657 Office: 970.479.2139 Inspections: inspections@vailgov.com Construction B18-0139 / Revision 001 Issued: 10/08/2018 TOWN OF VAIL Property Information Address: 100 E MEADOW DR 22 ( 210108256022 ) Unit #: 22 Parcel Number: 210108256022 Legal Description:Subdivision: VAIL VILLAGE PLAZA CONDOS Unit: 22 BK-0388 PG-0855 BK-0684 PG-0190 WD 12-15- 95 Contacts Contact Type: Applicant Full Name: Michael Current Address: PO Box 5293 X Vail, CO 81657 Phone: 9703316345 Contact Type: Property Owner Full Name: AJW PROPERTIES II LLC Address: Phone: None Contact Type: Property Owner Full Name: AJW PROPERTIES II LLC Address: 2910 BOOTH CREEK DR 8 VAIL, CO 81657-4604 Phone: None Contact Type: Property Owner Full Name: AJW PROPERTIES II LLC Address: 2910 BOOTH CREEK DR 21 VAIL, CO 81657-4604 Phone: None Contact Type: Property Owner Full Name: AJW PROPERTIES II LLC Address: 2910 BOOTH CREEK DR 22 VAIL, CO 81657-4604 Phone: None Contact Type: Site Superintendent Full Name: Mark Schnupp Address: Phone: 970-390-7098 Contractor Contractor Type: General Company: Rocky Mountain Construction Group State License #: Phone: 970-476-4458 Project Information Project Name: AJW Properties II LLC 2018 Project Description: REV1-Exterior-flue termination Interior-add fireplace lower level,revise stair-no changes to existing stair layout/structure, new railing (Renovation of Units 7A, 8, 21, and 22. Interior remodel including architectural finishes and new electrical and mechanical systems. Exterior renovation including TOV DRB and VVIPCA HOA approved changes to one new roof, exterior finishes, and window and door modifications.) Fees Paid Account #: 001-0000.31111.00 - Building Permit Fee Fee Amount:$2,931.35 Account #: 001-0000.31123.00 - Building Plan Review Fee Fee Amount:$1,905.38 Account #: 110-0000.31060.00 - Construction Use Tax Fee Fee Amount:$8,710.00 Account #: 001-0000.31111.00 - Mechanical Permit Fee Fee Amount:$1,500.00 Account #: 001-0000.31123.00 - Mechanical Plan Review Fee Fee Amount:$375.00 Account #: 001-0000.31111.00 - Plumbing Permit Fee Fee Amount:$315.00 Account #: 001-0000.31123.00 - Plumbing Plan Review Fee Fee Amount:$78.75 Account #: 001-0000.31111.00 - Revision Fee Fee Amount:$220.00 Account #: 001-0000.31128.00 - Will Call Fee (Building Scope)Fee Amount:$5.00 Account #: 001-0000.31128.00 - Will Call Fee (Mechanical Scope)Fee Amount:$5.00 Account #: 001-0000.31128.00 - Will Call Fee (Plumbing Scope)Fee Amount:$5.00 Total Paid: $16,050.48 Conditions CONDITIONS UNDER WHICH PERMITS BECOME VOID: If construction is not begun within 6 months from the date permit was issued. If more than 5 months elapses between inspections. If incorrect information is given on the application at the time the permit was issued. Christopher Jarecki - Town of Vail Building Official NOTICE: By issuance of this Permit the applicant agrees to comply with all Titles of the Town of Vail Code and all applicable State and Federal law. Failure to do so will void this Permit and the applicant shall forfeit all applicable fees. COMcheck Software Version 4.0.7.1 Interior Lighting Compliance Certificate Project Title: 2015 IECC Project Type:New Construction Construction Site: 100 East Meadow Drive Vail, CO 81657 Owner/Agent: Mark Current Current Architects PO Box 5393 Vail, CO 81657 970.331.6345 michael@currentarchitects.com Designer/Contractor: BG Buildingworks 222 Chapel Place, Unit AC-201 Avon, CO 81620 970.949.6108 Project Information Energy Code: 100 East Meadow Drive Reduced interior lighting power. Requirements are implicitly enforced within interior lighting allowance calculations. Additional Efficiency Package Allowed Interior Lighting Power A Area Category B Floor Area (ft2) C Allowed Watts / ft2 D Allowed Watts (B X C) 1-Retail 3650 1.13 4139 4139Total Allowed Watts = Proposed Interior Lighting Power E (C X D) D Fixture Watt. A Fixture ID : Description / Lamp / Wattage Per Lamp / Ballast B Lamps/ Fixture C # of Fixtures 1-Retail LED 1: R1/R1E: Other: 1 33 19 627 LED 9: R1: Other: 1 2 19 Exempt Exemption:Retail Display Window LED 2: R2: Other: 1 7 33 231 LED 3: R3: Other: 1 13 50 644 LED 4: R4: Other: 1 6 16 99 LED 5: R5/R5E: Other: 1 11 19 209 Incandescent 1: P1: Other: 1 4 320 1280 LED 6: S1: Other: 1 2 9 17 LED 7: T1: Other: 1 436 4 Exempt Exemption:Furniture-mounted Supplemental Task Lighting Track lighting 1: T4: Wattage based on 16 feet of track 0 0 480 Exempt Exemption:Retail Display Window Track lighting 2: T12: Wattage based on 24 feet of track 0 0 720 720 LED 8: V1: Other: 1 1 96 96 3923Total Proposed Watts = Project Title: Data filename: 100 East Meadow Drive S:\BGProjects\9949.00 100 East Meadow Drive Retail\Engineering\Energy\Calculations\100 EMD COMcheck.cck 04/13/18Report date: 61 of Page Interior Lighting Compliance Statement Compliance Statement: The proposed interior lighting design represented in this document is consistent with the building plans, specifications, and other calculations submitted with this permit application. The proposed interior lighting systems have been designed to meet the 2015 IECC requirements in COMcheck Version 4.0.7.1 and to comply with any applicable mandatory requirements listed in the Inspection Checklist. Name - Title Signature Date Interior Lighting PASSES: Design 5% better than code Project Title: Data filename: 100 East Meadow Drive S:\BGProjects\9949.00 100 East Meadow Drive Retail\Engineering\Energy\Calculations\100 EMD COMcheck.cck 04/13/18Report date: 62 of Page Brent Schumacher - Electrical Engineer 04.13.2018 Inspection Checklist Requirements: 90.0% were addressed directly in the COMcheck software COMcheck Software Version 4.0.7.1 Text in the "Comments/Assumptions" column is provided by the user in the COMcheck Requirements screen. For each requirement, the user certifies that a code requirement will be met and how that is documented, or that an exception is being claimed. Where compliance is itemized in a separate table, a reference to that table is provided. Energy Code: 2015 IECC Section # & Req.ID Plan Review Complies? Comments/Assumptions C103.2 [PR4]1 Plans, specifications, and/or calculations provide all information with which compliance can be determined for the interior lighting and electrical systems and equipment and document where exceptions to the standard are claimed. Information provided should include interior lighting power calculations, wattage of bulbs and ballasts, transformers and control devices. Complies Does Not Not Observable Not Applicable C406 [PR9]1 Plans, specifications, and/or calculations provide all information with which compliance can be determined for the additional energy efficiency package options. Complies Does Not Not Observable Not Applicable Additional Comments/Assumptions: 1 High Impact (Tier 1) 2 Medium Impact (Tier 2) 3 Low Impact (Tier 3) Project Title: Data filename: 100 East Meadow Drive S:\BGProjects\9949.00 100 East Meadow Drive Retail\Engineering\Energy\Calculations\100 EMD COMcheck.cck 04/13/18Report date: 63 of Page Section # & Req.ID Rough-In Electrical Inspection Complies? Comments/Assumptions C405.2.1 [EL15]1 Lighting controls installed to uniformly reduce the lighting load by at least 50%. Complies Does Not Not Observable Not Applicable Requirement will be met. Location on plans/spec: E-000, E-101, E-102 C405.2.1 [EL18]1 Occupancy sensors installed in required spaces. Complies Does Not Not Observable Not Applicable Requirement will be met. Location on plans/spec: E-000, E-101, E-102 C405.2.1, C405.2.2. 3 [EL23]2 Independent lighting controls installed per approved lighting plans and all manual controls readily accessible and visible to occupants. Complies Does Not Not Observable Not Applicable Requirement will be met. Location on plans/spec: E-000, E-101, E-102 C405.2.2. 1 [EL22]2 Automatic controls to shut off all building lighting installed in all buildings. Complies Does Not Not Observable Not Applicable Requirement will be met. Location on plans/spec: E-000, E-101, E-102 C405.2.3 [EL16]2 Daylight zones provided with individual controls that control the lights independent of general area lighting. Complies Does Not Not Observable Not Applicable Exception: Requirement does not apply. Location on plans/spec: E-000, E-101, E-102 C405.2.3, C405.2.3. 1, C405.2.3. 2 [EL20]1 Primary sidelighted areas are equipped with required lighting controls. Complies Does Not Not Observable Not Applicable Exception: Lighting required to have specific application controls. Location on plans/spec: E-000, E-101, E-102 C405.2.3, C405.2.3. 1, C405.2.3. 3 [EL21]1 Enclosed spaces with daylight area under skylights and rooftop monitors are equipped with required lighting controls. Complies Does Not Not Observable Not Applicable Exception: Requirement does not apply. C405.2.4 [EL4]1 Separate lighting control devices for specific uses installed per approved lighting plans. Complies Does Not Not Observable Not Applicable Requirement will be met. Location on plans/spec: E-000, E-101, E-102 C405.2.4 [EL8]1 Additional interior lighting power allowed for special functions per the approved lighting plans and is automatically controlled and separated from general lighting. Complies Does Not Not Observable Not Applicable Requirement will be met. Location on plans/spec: E-000, E-101, E-102 C405.3 [EL6]1 Exit signs do not exceed 5 watts per face. Complies Does Not Not Observable Not Applicable Requirement will be met. Location on plans/spec: E-200 Additional Comments/Assumptions: 1 High Impact (Tier 1) 2 Medium Impact (Tier 2) 3 Low Impact (Tier 3) Project Title: Data filename: 100 East Meadow Drive S:\BGProjects\9949.00 100 East Meadow Drive Retail\Engineering\Energy\Calculations\100 EMD COMcheck.cck 04/13/18Report date: 64 of Page Section # & Req.ID Final Inspection Complies? Comments/Assumptions C303.3, C408.2.5. 2 [FI17]3 Furnished O&M instructions for systems and equipment to the building owner or designated representative. Complies Does Not Not Observable Not Applicable C405.4.1 [FI18]1 Interior installed lamp and fixture lighting power is consistent with what is shown on the approved lighting plans, demonstrating proposed watts are less than or equal to allowed watts. Complies Does Not Not Observable Not Applicable See the Interior Lighting fixture schedule for values. C408.2.5. 1 [FI16]3 Furnished as-built drawings for electric power systems within 90 days of system acceptance. Complies Does Not Not Observable Not Applicable C408.3 [FI33]1 Lighting systems have been tested to ensure proper calibration, adjustment, programming, and operation. Complies Does Not Not Observable Not Applicable Additional Comments/Assumptions: 1 High Impact (Tier 1) 2 Medium Impact (Tier 2) 3 Low Impact (Tier 3) Project Title: Data filename: 100 East Meadow Drive S:\BGProjects\9949.00 100 East Meadow Drive Retail\Engineering\Energy\Calculations\100 EMD COMcheck.cck 04/13/18Report date: 65 of Page Project Title: Data filename: 100 East Meadow Drive S:\BGProjects\9949.00 100 East Meadow Drive Retail\Engineering\Energy\Calculations\100 EMD COMcheck.cck 04/13/18Report date: 66 of Page COMcheck Software Version 4.0.7.0 Mechanical Compliance Certificate Project Title: 2015 IECC Project Type:New Construction Location:Vail, Colorado Climate Zone:6b Construction Site: Owner/Agent: Designer/Contractor: Project Information Energy Code: Reduced interior lighting power. Requirements are implicitly enforced within interior lighting allowance calculations. Additional Efficiency Package Mechanical Systems List Quantity System Type & Description Heating: 1 each - Other, Gas, Capacity = 40 kBtu/h No minimum efficiency requirement applies Fan System: None 1 Lower Level Baseboard (Multiple-Zone): VRF, Air Cooled Heat Pump Heating Mode: Capacity = 36 kBtu/h, No minimum efficiency requirement applies Cooling Mode: Capacity = 36 kBtu/h, No minimum efficiency requirement applies Fan System: FAN SYSTEM 1 -- Compliance (Motor nameplate HP method) : Fails: Fan system has no fans Fans: 2 Multi-Split Heat Pumps (Multiple-Zone): Mechanical Compliance Statement Compliance Statement: The proposed mechanical design represented in this document is consistent with the building plans, specifications, and other calculations submitted with this permit application. The proposed mechanical systems have been designed to meet the 2015 IECC requirements in COMcheck Version 4.0.7.0 and to comply with any applicable mandatory requirements listed in the Inspection Checklist. Name - Title Signature Date Project Title: Data filename: S:\BGProjects\9949.00 100 East Meadow Drive Retail\Engineering\Energy\Calculations\100 EMD COMcheck.cck 04/13/18Report date: 101 of Page Steven Shea 04.13.2018 Inspection Checklist Requirements: 75.0% were addressed directly in the COMcheck software COMcheck Software Version 4.0.7.0 Text in the "Comments/Assumptions" column is provided by the user in the COMcheck Requirements screen. For each requirement, the user certifies that a code requirement will be met and how that is documented, or that an exception is being claimed. Where compliance is itemized in a separate table, a reference to that table is provided. Energy Code: 2015 IECC Section # & Req.ID Plan Review Complies? Comments/Assumptions C103.2 [PR2]1 Plans, specifications, and/or calculations provide all information with which compliance can be determined for the mechanical systems and equipment and document where exceptions to the standard are claimed. Load calculations per acceptable engineering standards and handbooks. Complies Does Not Not Observable Not Applicable Requirement will be met. C406 [PR9]1 Plans, specifications, and/or calculations provide all information with which compliance can be determined for the additional energy efficiency package options. Complies Does Not Not Observable Not Applicable Additional Comments/Assumptions: 1 High Impact (Tier 1) 2 Medium Impact (Tier 2) 3 Low Impact (Tier 3) Project Title: Data filename: S:\BGProjects\9949.00 100 East Meadow Drive Retail\Engineering\Energy\Calculations\100 EMD COMcheck.cck 04/13/18Report date: 102 of Page Section # & Req.ID Footing / Foundation Inspection Complies? Comments/Assumptions C403.2.4. 5, C403.2.4. 6 [FO9]3 Snow/ice melting system sensors for future connection to controls. Freeze protection systems have automatic controls installed. Complies Does Not Not Observable Not Applicable Exception: Requirement does not apply. Additional Comments/Assumptions: 1 High Impact (Tier 1) 2 Medium Impact (Tier 2) 3 Low Impact (Tier 3) Project Title: Data filename: S:\BGProjects\9949.00 100 East Meadow Drive Retail\Engineering\Energy\Calculations\100 EMD COMcheck.cck 04/13/18Report date: 103 of Page Section # & Req.ID Plumbing Rough-In Inspection Complies? Comments/Assumptions C404.5, C404.5.1, C404.5.2 [PL6]3 Heated water supply piping conforms to pipe length and volume requirements. Refer to section details. Complies Does Not Not Observable Not Applicable Requirement will be met. C404.5, C404.5.1, C404.5.2 [PL6]3 Heated water supply piping conforms to pipe length and volume requirements. Refer to section details. Complies Does Not Not Observable Not Applicable Requirement will be met. C404.6.3 [PL7]3 Pumps that circulate water between a heater and storage tank have controls that limit operation from startup to <= 5 minutes after end of heating cycle. Complies Does Not Not Observable Not Applicable Requirement will be met. C404.6.3 [PL7]3 Pumps that circulate water between a heater and storage tank have controls that limit operation from startup to <= 5 minutes after end of heating cycle. Complies Does Not Not Observable Not Applicable Requirement will be met. C404.7 [PL8]3 Water distribution system that pumps water from a heated-water supply pipe back to the heated-water source through a cold-water supply pipe is a demand recirculation water system. Pumps within this system have controls that start the pump upon receiving a signal from the action of a user of a fixture or appliance and limits the temperature of the water entering the cold-water piping to 104°F. Complies Does Not Not Observable Not Applicable Requirement will be met. C404.7 [PL8]3 Water distribution system that pumps water from a heated-water supply pipe back to the heated-water source through a cold-water supply pipe is a demand recirculation water system. Pumps within this system have controls that start the pump upon receiving a signal from the action of a user of a fixture or appliance and limits the temperature of the water entering the cold-water piping to 104°F. Complies Does Not Not Observable Not Applicable Requirement will be met. Additional Comments/Assumptions: 1 High Impact (Tier 1) 2 Medium Impact (Tier 2) 3 Low Impact (Tier 3) Project Title: Data filename: S:\BGProjects\9949.00 100 East Meadow Drive Retail\Engineering\Energy\Calculations\100 EMD COMcheck.cck 04/13/18Report date: 104 of Page Section # & Req.ID Mechanical Rough-In Inspection Complies? Comments/Assumptions C402.2.6 [ME41]3 Thermally ineffective panel surfaces of sensible heating panels have insulation >= R-3.5. Complies Does Not Not Observable Not Applicable Exception: Requirement does not apply. C403.2.12 .1 [ME65]3 HVAC fan systems at design conditions do not exceed allowable fan system motor nameplate hp or fan system bhp. Complies Does Not Not Observable Not Applicable Exception: Requirement does not apply. See the Mechanical Systems list for values. C403.2.12 .1 [ME65]3 HVAC fan systems at design conditions do not exceed allowable fan system motor nameplate hp or fan system bhp. Complies Does Not Not Observable Not Applicable Requirement will be met. See the Mechanical Systems list for values. C403.2.12 .3 [ME117]2 Fans have efficiency grade (FEG) >= 67. The total efficiency of the fan at the design point of operation <= 15% of maximum total efficiency of the fan. Complies Does Not Not Observable Not Applicable Requirement will be met. C403.2.12 .3 [ME117]2 Fans have efficiency grade (FEG) >= 67. The total efficiency of the fan at the design point of operation <= 15% of maximum total efficiency of the fan. Complies Does Not Not Observable Not Applicable Requirement will be met. C403.2.13 [ME71]2 Unenclosed spaces that are heated use only radiant heat. Complies Does Not Not Observable Not Applicable Exception: Requirement does not apply. C403.2.3 [ME55]2 HVAC equipment efficiency verified. Complies Does Not Not Observable Not Applicable See the Mechanical Systems list for values. C403.2.4. 4 [ME112]3 Zone isolation devices and controls installed where applicable. Complies Does Not Not Observable Not Applicable Requirement will be met. C403.2.4. 4 [ME112]3 Zone isolation devices and controls installed where applicable. Complies Does Not Not Observable Not Applicable Requirement will be met. C403.2.6. 1 [ME59]1 Demand control ventilation provided for spaces >500 ft2 and >25 people/1000 ft2 occupant density and served by systems with air side economizer, auto modulating outside air damper control, or design airflow >3,000 cfm. Complies Does Not Not Observable Not Applicable Exception: Requirement does not apply. C403.2.6. 2 [ME115]3 Enclosed parking garage ventilation has automatic contaminant detection and capacity to stage or modulate fans to 50% or less of design capacity. Complies Does Not Not Observable Not Applicable Exception: Requirement does not apply. C403.2.7 [ME57]1 Exhaust air energy recovery on systems meeting Table C403.2.7(1) and C403.2.7(2). Complies Does Not Not Observable Not Applicable Requirement will be met. 1 High Impact (Tier 1) 2 Medium Impact (Tier 2) 3 Low Impact (Tier 3) Project Title: Data filename: S:\BGProjects\9949.00 100 East Meadow Drive Retail\Engineering\Energy\Calculations\100 EMD COMcheck.cck 04/13/18Report date: 105 of Page Section # & Req.ID Mechanical Rough-In Inspection Complies? Comments/Assumptions C403.2.8 [ME116]3 Kitchen exhaust systems comply with replacement air and conditioned supply air limitations, and satisfy hood rating requirements and maximum exhaust rate criteria. Complies Does Not Not Observable Not Applicable Exception: Requirement does not apply. C403.2.9 [ME60]2 HVAC ducts and plenums insulated. Where ducts or plenums are installed in or under a slab, verification may need to occur during Foundation Inspection. Complies Does Not Not Observable Not Applicable Exception: Requirement does not apply. C403.2.9 [ME10]2 Ducts and plenums sealed based on static pressure and location. Complies Does Not Not Observable Not Applicable Requirement will be met. C403.2.9. 1.3 [ME11]3 Ductwork operating >3 in. water column requires air leakage testing. Complies Does Not Not Observable Not Applicable Exception: Requirement does not apply. C403.2.9. 1.3 [ME11]3 Ductwork operating >3 in. water column requires air leakage testing. Complies Does Not Not Observable Not Applicable Exception: Requirement does not apply. C403.4.1. 1 [ME75]2 Hydronic and multizone HVAC system controls areVAV fans driven by mechanical or electrical variable speed drive per Table C403.4.1.1. Complies Does Not Not Observable Not Applicable Exception: Requirement does not apply. C403.4.1. 1 [ME75]2 Hydronic and multizone HVAC system controls areVAV fans driven by mechanical or electrical variable speed drive per Table C403.4.1.1. Complies Does Not Not Observable Not Applicable Exception: Requirement does not apply. C403.4.1. 2 [ME67]2 VAV fans have static pressure sensors located so controller setpoint <=1.2 w.c.. Complies Does Not Not Observable Not Applicable Exception: Requirement does not apply. C403.4.1. 2 [ME67]2 VAV fans have static pressure sensors located so controller setpoint <=1.2 w.c.. Complies Does Not Not Observable Not Applicable Exception: Requirement does not apply. C403.4.1. 3 [ME24]2 Reset static pressure setpoint for DDC controlled VAV boxes reporting to central controller based on the zones requiring the most pressure. Complies Does Not Not Observable Not Applicable Exception: Requirement does not apply. C403.4.1. 3 [ME24]2 Reset static pressure setpoint for DDC controlled VAV boxes reporting to central controller based on the zones requiring the most pressure. Complies Does Not Not Observable Not Applicable Exception: Requirement does not apply. C403.4.2. 3.2.2 [ME122]3 Open- or closed circuit cooling towers have a separate heat exchanger to isolate the cooling tower from the heat pump loop, and heat loss is controlled by shutting down the circulation pump on the cooling tower loop. Complies Does Not Not Observable Not Applicable Exception: Requirement does not apply. 1 High Impact (Tier 1) 2 Medium Impact (Tier 2) 3 Low Impact (Tier 3) Project Title: Data filename: S:\BGProjects\9949.00 100 East Meadow Drive Retail\Engineering\Energy\Calculations\100 EMD COMcheck.cck 04/13/18Report date: 106 of Page Section # & Req.ID Mechanical Rough-In Inspection Complies? Comments/Assumptions C403.4.4. 6 [ME110]3 Multiple zone VAV systems with DDC of individual zone boxes have static pressure setpoint reset controls. Complies Does Not Not Observable Not Applicable Exception: Requirement does not apply. See the Mechanical Systems list for values. C403.4.4. 6 [ME110]3 Multiple zone VAV systems with DDC of individual zone boxes have static pressure setpoint reset controls. Complies Does Not Not Observable Not Applicable Exception: Requirement does not apply. See the Mechanical Systems list for values. C408.2.2. 1 [ME53]3 Air outlets and zone terminal devices have means for air balancing. Complies Does Not Not Observable Not Applicable Requirement will be met. Additional Comments/Assumptions: 1 High Impact (Tier 1) 2 Medium Impact (Tier 2) 3 Low Impact (Tier 3) Project Title: Data filename: S:\BGProjects\9949.00 100 East Meadow Drive Retail\Engineering\Energy\Calculations\100 EMD COMcheck.cck 04/13/18Report date: 107 of Page Section # & Req.ID Final Inspection Complies? Comments/Assumptions C303.3, C408.2.5. 3 [FI8]3 Furnished O&M manuals for HVAC systems within 90 days of system acceptance. Complies Does Not Not Observable Not Applicable Requirement will be met. C403.2.2 [FI27]3 HVAC systems and equipment capacity does not exceed calculated loads. Complies Does Not Not Observable Not Applicable Requirement will be met. C403.2.4. 1 [FI47]3 Heating and cooling to each zone is controlled by a thermostat control. Minimum one humidity control device per installed humidification/dehumidification system. Complies Does Not Not Observable Not Applicable Requirement will be met. C403.2.4. 1 [FI47]3 Heating and cooling to each zone is controlled by a thermostat control. Minimum one humidity control device per installed humidification/dehumidification system. Complies Does Not Not Observable Not Applicable Requirement will be met. C403.2.4. 1.1 [FI42]3 Heat pump controls prevent supplemental electric resistance heat from coming on when not needed. Complies Does Not Not Observable Not Applicable C403.2.4. 1.2 [FI38]3 Thermostatic controls have a 5 °F deadband. Complies Does Not Not Observable Not Applicable Requirement will be met. C403.2.4. 1.3 [FI20]3 Temperature controls have setpoint overlap restrictions. Complies Does Not Not Observable Not Applicable Requirement will be met. C403.2.4. 2 [FI39]3 Each zone equipped with setback controls using automatic time clock or programmable control system. Complies Does Not Not Observable Not Applicable Requirement will be met. C403.2.4. 2.1, C403.2.4. 2.2 [FI40]3 Automatic Controls: Setback to 55°F (heat) and 85°F (cool); 7-day clock, 2- hour occupant override, 10-hour backup Complies Does Not Not Observable Not Applicable Requirement will be met. C408.2.1 [FI28]1 Commissioning plan developed by registered design professional or approved agency. Complies Does Not Not Observable Not Applicable Requirement will be met. C408.2.3. 1 [FI31]1 HVAC equipment has been tested to ensure proper operation. Complies Does Not Not Observable Not Applicable Requirement will be met. C408.2.3. 2 [FI10]1 HVAC control systems have been tested to ensure proper operation, calibration and adjustment of controls. Complies Does Not Not Observable Not Applicable Requirement will be met. 1 High Impact (Tier 1) 2 Medium Impact (Tier 2) 3 Low Impact (Tier 3) Project Title: Data filename: S:\BGProjects\9949.00 100 East Meadow Drive Retail\Engineering\Energy\Calculations\100 EMD COMcheck.cck 04/13/18Report date: 108 of Page Section # & Req.ID Final Inspection Complies? Comments/Assumptions C408.2.4 [FI29]1 Preliminary commissioning report completed and certified by registered design professional or approved agency. Complies Does Not Not Observable Not Applicable Requirement will be met. C408.2.5. 1 [FI7]3 Furnished HVAC as-built drawings submitted within 90 days of system acceptance. Complies Does Not Not Observable Not Applicable Requirement will be met. C408.2.5. 3 [FI43]1 An air and/or hydronic system balancing report is provided for HVAC systems. Complies Does Not Not Observable Not Applicable Requirement will be met. C408.2.5. 4 [FI30]1 Final commissioning report due to building owner within 90 days of receipt of certificate of occupancy. Complies Does Not Not Observable Not Applicable Requirement will be met. Additional Comments/Assumptions: 1 High Impact (Tier 1) 2 Medium Impact (Tier 2) 3 Low Impact (Tier 3) Project Title: Data filename: S:\BGProjects\9949.00 100 East Meadow Drive Retail\Engineering\Energy\Calculations\100 EMD COMcheck.cck 04/13/18Report date: 109 of Page Project Title: Data filename: S:\BGProjects\9949.00 100 East Meadow Drive Retail\Engineering\Energy\Calculations\100 EMD COMcheck.cck 04/13/18Report date: 1010 of Page 75 South Frontage Road West, Vail, CO 81657 Office: 970.479.2139 Inspection Line: 970.479.2149 Construction B18-0139 Issued: 05/30/2018 TOWN OF VAIL Property Information Address: 100 E MEADOW DR 7A (210108256036 7A) ( 210108256036 ) Unit #: 7A Parcel Number: 210108256036 Legal Description:Subdivision: VAIL VILLAGE PLAZA CONDOS Unit: 7A BK-0525 PG-0640 DEC 03-22-90 BK-0684 PG- 0190 WD 12-15-95 Contacts Contact Type: Applicant Full Name: Michael Current Address: PO Box 5293 X Vail, CO 81657 Phone: 9703316345 Contact Type: Property Owner Full Name: AJW PROPERTIES II LLC Address: 2910 BOOTH CREEK DR 22 VAIL, CO 81657-4604 Phone: None Contact Type: Property Owner Full Name: AJW PROPERTIES II LLC Address: 2910 BOOTH CREEK DR 21 VAIL, CO 81657-4604 Phone: None Contact Type: Property Owner Full Name: AJW PROPERTIES II LLC Address: 2910 BOOTH CREEK DR 8 VAIL, CO 81657-4604 Phone: None Contact Type: Property Owner Full Name: AJW PROPERTIES II LLC Address: Phone: None Contractor Contractor Type: General Company: Rocky Mountain Construction Group State License #: Phone: 970-476-4458 Project Information Project Name: AJW Properties II LLC 2018 Project Description: Renovation of Units 7A, 8, 21, and 22. Interior remodel including architectural finishes and new electrical and mechanical systems. Exterior renovation including TOV DRB and VVIPCA HOA approved changes to one new roof, exterior finishes, and window and door modifications. Fees Paid Account #: 001-0000.31111.00 - Building Permit Fee Fee Amount:$2,931.35 Account #: 001-0000.31123.00 - Building Plan Review Fee Fee Amount:$1,905.38 Account #: 110-0000.31060.00 - Construction Use Tax Fee Fee Amount:$8,710.00 Account #: 001-0000.31111.00 - Mechanical Permit Fee Fee Amount:$1,500.00 Account #: 001-0000.31123.00 - Mechanical Plan Review Fee Fee Amount:$375.00 Account #: 001-0000.31111.00 - Plumbing Permit Fee Fee Amount:$315.00 Account #: 001-0000.31123.00 - Plumbing Plan Review Fee Fee Amount:$78.75 Account #: 001-0000.31128.00 - Will Call Fee (Building Scope)Fee Amount:$5.00 Account #: 001-0000.31128.00 - Will Call Fee (Mechanical Scope)Fee Amount:$5.00 Account #: 001-0000.31128.00 - Will Call Fee (Plumbing Scope)Fee Amount:$5.00 Total Paid:$15,830.48 Conditions CONDITIONS UNDER WHICH PERMITS BECOME VOID: If construction is not begun within 6 months from the date permit was issued. If more than 5 months elapses between inspections. If incorrect information is given on the application at the time the permit was issued. Christopher Jarecki - Town of Vail Building Official NOTICE: By issuance of this Permit the applicant agrees to comply with all Titles of the Town of Vail Code and all applicable State and Federal law. Failure to do so will void this Permit and the applicant shall forfeit all applicable fees.