The URL can be used to link to this page

Home My WebLink AboutB18-0105_Approved Calcs_1524856387.pdfPage 1 of 4 2/26/2018 P.O. Box 7627, Avon, CO 81620 | P: 970.306.4233 | F: 866.403.3485 | www.activeenergies.com Solar Installation Information Vendor: Active Energies Solar LLC PO Box 7627 Avon, CO 81620 (970-306-4233 /info@activeenergies.com) Site: Bivona Residence 2373B Lower Traverse Way Vail, CO 81657 Equipment: Panels: 12 Solaria PowerXT all black solar panels @ 350watts Inverter: 12 SolarEdge P400 Optimizers + 1 SolarEdge SE3800H-US inverter Mounting Equipment: Unirac all black racking system with DPW easy feet mounting feet Monitoring: SolarEdge Remote Energy Monitoring System System Layout: Single Panel = 5.32ft tall X 3.66ft wide Panel Arrangement: 2 rows of 6 with all panels oriented in the portrait position, mounted flush on the southwest facing roof Holy Cross electric meter located on the south west side of the building. Production meter to be located adjacent to the Holy Cross meter. Inverter to be located in the garage. Minimum Designed Temperature: -40°F Maximum Ambient Design Temperature: 140°F All AC wiring to be completed by a Colorado licensed master electrician All DC wiring to be overseen by NABCEP certified installer Net Meter and Production Meter Production Meter Unit #5 Net Meter Bivona Residence #5 Page 2 of 4 2/26/2018 P.O. Box 7627, Avon, CO 81620 | P: 970.306.4233 | F: 866.403.3485 | www.activeenergies.com Calculations 4.2kW System Size (STC) Panels: 12 Solaria PowerXT all black solar panels @ 350watts Inverter: 12 SolarEdge P400 Optimizers Inverter: SolarEdge SE3800H-US Inverter (1 string of 12 modules/optimizers) Array tilt angle: 14.04° Array azimuth: 230º (where 180º is south) Estimated annual power production: 5,520kWh Maximum PV System Voltage: 690.7 Voc = 47.1V/module 47.1V x 1 module = 47.1V Temperature correction factor 690.7(A) Temperature Coefficient (Voc) = -0.29%/°C (-65C° x (-.0029C°)) = .19% ((.19% x 47.1V) x 1 panels) + 47.1V = 55.9V Maximum PV Source Circuit (String) Current: 690.8 (A)(1) Isc = 9.49A 9.49A x 1.25 = 11.9A Maximum PV Output Circuit (Array) Current: 690.8 (A)(2) Max Inverter Input Circuit 10.5A Inverter Output Circuit Current: 690.8 (A)(3) 16A @ 240V Page 3 of 4 2/26/2018 P.O. Box 7627, Avon, CO 81620 | P: 970.306.4233 | F: 866.403.3485 | www.activeenergies.com Conductor Sizing Roof Pass Thru Box to DC Disconnect/Inverter: Max Inverter Input Circuit 10.5A 10.5A x 125% = 13.1A 690.8 (B)(1) #10 THWN-2 Table 310.16 40A (75ºC column) Conduit fill adjustment Table 310.15 (B)(2)(a) No Conduit Fill Temperature correction factor Table 310.16 No temperature correction From Inverter to AC Disconnect/Production Meter/Backfeed Point: Nameplate maximum continuous output current: 16A 16A x 125% = 20A #10 THWN-2 Table 310.16 35A (75ºC column) No Conduit fill adjustment Table 310.15 (B)(2)(a) No Temperature correction factor Table 310.16 Overcurrent Protection Devices 1 - 20A two pole breaker Backfeed Breaker Conductors may be oversized for Voltage Drop Page 4 of 4 2/26/2018 P.O. Box 7627, Avon, CO 81620 | P: 970.306.4233 | F: 866.403.3485 | www.activeenergies.com SolarEdge SE3800H-US Inverter w/ Integrated Disconnect NEMA 3R Max AC Output: 16A @ 240V With ARC Fault Protection & Rapid Shutdown compliant – in the garage DC Grounding Electrode Conductor solid bare #6 Cu, per NEC 250.66(C) Service Panel Located in garage Line Diagram Bivona Residence 2373 Lower Traverse Way #5 Vail, CO 81657 4.2 kW Utility Interactive Photovoltaic System Modules: 12 x Solaria Power XT 350w Voc = 47.1V Isc = 9.49A Optimizers: 12 SolarEdge P370 1 String X 12 Modules/Optimizer Inverter: SolarEdge SE3800H-US Operating Voltage: 380V Operating Current: 15A Max System Voltage: 480V Max Output Current: 16A Tilt Angle: 14.04° Array Azimuth: 230° Production: 5,520kWh/yr Notes: - See Calculation Sheet for conductor sizing. - All conductors are copper unless otherwise noted. - Inverter listed (UL-1741) to de- energize upon loss of utility voltage per NEC 690.61. - Inverter has integral ground-fault protection per NEC 690.5 - 240V 1 Phase Service Panel rating of 200A (bus rating 200 amp and 200 Main disconnect) to accommodate 20A (PV) + 200A (Main) = 220A supply (up to 120% of connected power sources from installations per NEC 705(D)(2)(3)(b) Pass Thru Box Located on Roof Placardstating”PhotovoltaicSystemConnected” 2 #10 PV Wire 1# 6G Bare Cu Conductors in Free Air Array mounted on roof 12 Solaria PowerXT 350w Solar Panels 12 SolarEdge P370 DC Optimizers 1 2 3 1212... ~5' ¾” C EMT/PVC 3 #10 THWN-2 1 #10 G THWN-2 Backfeed Breaker 20A 2P 240v ~50' ¾” EMT/MC Cable 2 #10 THWN-2 1 #10 G THWN-2 20A Production Meter Adjacent to net meter ~5' ¾” C EMT/PVC 3 #10 THWN-2 1 #10 G THWN-2 Net meter located on the west wall of building #2 About Solaria Established in 2000, The Solaria Corporation has created one of the industry’s most respected IP portfolios, with over 100 patents encompassing materials, processes, applications, products, manufacturing automation and equipment. Headquartered in Fremont, California, Solaria has developed a technology platform that unlocks the potential of solar energy allowing it to be ubiquitous and universally accessed. Achieving up to 19.4% efficiency, Solaria PowerXT solar modules are one of the highest power modules in the residential solar market. Compared to conventional modules, Solaria PowerXT modules have fewer gaps between the solar cells; this leads to higher power and superior aesthetics. Solaria PowerXT residential modules are manufactured with black backsheet and frames, giving them a striking appearance. Developed in California, Solaria’s patented cell cutting and module assembly takes processed solar wafers and turns them into PowerXT solar modules. The process starts by creating a highly reliable PowerXT cell where busbars and ribbon interconnections are eliminated. Solaria then packages the cells into the PowerXT solar module, reducing inactive space between the cells. All of the above leads to an exceptionally efficient solar module produced in a cost effective manner. Higher Efficiency, Higher Power Solaria PowerXT modules achieve up to 19.4% efficiency; conventional modules achieve 15% – 17% efficiency. Solaria PowerXT modules are one of the highest power modules available. Lower System Costs Solaria PowerXT modules produce more power per square meter area. This reduces installation costs due to fewer balance of system components. Improved Shading Tolerance Sub-strings are interconnected in parallel, within each of the four module quadrants, which dramatically lowers the shading losses and boosts energy yield. Improved Aesthetics Compared to conventional modules, Solaria PowerXT modules have a more uniform appearance and superior aesthetics. Durability and Reliability Solder-less cell interconnections are highly reliable and designed to far exceed the industry leading 25 year warranty. The Solaria Corporation 6200 Paseo Padre Parkway, Fremont, CA 94555 P: (510) 270-2500 www.solaria.com Copyright © 2017 The Solaria Corporation Product specifications are subject to change without notice. Rev 1E 12-21-2017 Solaria PowerXT ®-350R-PD | Solaria PowerXT®-345R-BD Solaria PowerXT® | Residential The Solaria Corporation 6200 Paseo Padre Parkway, Fremont, CA 94555 P: (510) 270-2500 www.solaria.com Copyright © 2017 The Solaria Corporation Product specifications are subject to change without notice. Rev 1E 12-21-2017 Solaria PowerXT®-350R-PD Solaria PowerXT®-345R-BD Performance at STC (1000W/m2, 25° C, AM 1.5) Solaria PowerXT- 340R-BD 345R-BD 345R-PD 350R-PD Max Power (Pmax) [W] 340 345 345 350 Efficiency [%] 18.8 19.1 19.1 19.4 Open Circuit Voltage (Voc) [V] 46.9 47.1 46.9 47.1 Short Circuit Current (Isc) [A] 9.36 9.40 9.46 9.49 Max Power Voltage (Vmp) [V] 38.6 38.9 38.5 38.8 Max Power Current (Imp) [A] 8.79 8.88 8.93 9.02 Power Tolerance [%] -0/+3 -0/+3 -0/+3 -0/+3 Performance at NOCT (800W/m2, 20°C Amb, Wind 1 m/s, AM 1.5) Max Power (Pmax) [W] 252 255 255 259 Open Circuit Voltage (Voc) [V] 44.1 44.3 44.1 44.3 Short Circuit Current (Isc) [A] 7.58 7.61 7.66 7.69 Max Power Voltage (Vmp) [V] 35.5 35.8 35.4 35.7 Max Power Current (Imp) [A] 7.03 7.10 7.15 7.22 Temperature Characteristics NOCT [ºC] 45 +/-2 Temp. Coeff. of Pmax [% / ºC] -0.39 Temp. Coeff. of Voc [% / ºC] -0.29 Temp. Coeff. of Isc [% / ºC] 0.04 Design Parameters Operating temperature [ºC] -40 to +85 Max System Voltage [V] 1000 Max Fuse Rating [A] 15 Bypass Diodes [#] 4 Mechanical Characteristics Cell Type Monocrystalline Silicon Dimensions (L x W x H) 1621mm x 1116mm x 40mm Weight 21 kg / 46 lbs Glass Type / Thickness AR Coated, Tempered / 3.2mm Frame Type Anodized Aluminum Cable Type / Length 12 AWG PV Wire (UL) / 1000mm Connector Type Amphenol H4 (MC4 compatible) Junction Box IP67 / 4 diodes Front Load (UL 1703) 5400 Pa / 113 psf Rear Load (UL 1703) 3600 Pa / 75 psf Certifications / Warranty Certifications UL 1703/IEC 61215/IEC 61730/CEC Fire Type (UL 1703) 1 Power & Product Warranty 25 years* * Warranty details at www.solaria.com Packaging Stacking Method Horizontal / Palletized Pcs / Pallet 25 Pallet Dims (L x W x H) 1685 x 1150 x 1230 mm Pallet Weight 590 kg / 1300 lbs Pallets / 40-ft Container 28 Pcs / 40-ft Container 700 Authorized Dealer 0 1 2 3 4 5 6 7 8 9 10 0 5 10 15 20 25 30 35 CURRENT (A)VOLTAGE (V) 1000W/m2 800W/m2 600W/m2 400W/m2 200W/m2 40 45 50 40 [63.8in±.2] 1621mm±5 [1in] 25mm [5.8in]148mm [5.8in]148mm [43.9in±.2] 1116mm±5 [1in] 25mm [35.43in] 900mm [15.04in] 382mm 4.5mm [0.18in] THRU ALL 4X GROUND 'A' 7mm [0.276in] X 10mm [0.394in] 4X MOUNTING SLOTS 'B' A B NEGATIVE (-) 1000 (3.3 ft) POSITIVE (+) 1000 (3.3 ft) B B B A AA MOUNTING SLOT [.3in]7mm [.4in] 10mm [1.57in] 40mm [.07in] 1.7mm [1.38in]35mm [.39in] 10mm IV Curves (350W Module) POWER OPTIMIZERSolarEdge Power Optimizer Module Add-On For North America P300 / P320 / P370 / P400 / P405 Up to 25% more energy Superior efficiency (99.5%) Mitgates all types of module mismatch losses, from manufacturing tolerance to partal shading Flexible system design for maximum space utlizaton Fast installaton with a single bolt Next generaton maintenance with module-level monitoring Module-level voltage shutdown for installer and firefighter safety PV power optimization at the module-level www.solaredge.usUSA - CANADA - GERMANY - ITALY - FRANCE - JAPAN - CHINA - AUSTRALIA - THE NETHERLANDS - UK - ISRAEL - TURKEY - SOUTH AFRICA - BULGARIA - INDIA © SolarEdge Technologies, Inc. All rights reserved. SOLAREDGE, the SolarEdge logo, OPTIMIZED BY SOLAREDGE are trademarks or registered trademarks of SolarEdge Technologies, Inc. All other trademarks mentioned herein are trademarks of their respective owners. Date: 03/2017 V.02. Subject to change without notice. (2) For detailed string sizing informaton refer to: htp://www.solaredge.com/sites/default/files/string_sizing_na.pdf. (3) It is not allowed to mix P405 with P300/P370/P400/P600/P700 in one string. P300 (for 60-cell mod- ules) P320 (for high-power 60-cell modules) P370 (for higher-power 60 and 72-cell modules) P400 (for 72 & 96-cell modules) P405 (for thin film modules) INPUT Rated Input DC Power(1) 300 320 370 400 405 W Absolute Maximum Input Voltage (Voc at lowest temperature)48 60 80 125 Vdc MPPT Operatng Range 8 - 48 8 - 60 8 - 80 12.5 - 105 Vdc Maximum Short Circuit Current (Isc) 10 11 10.1 Adc Maximum DC Input Current 12.5 13.75 12.63 Adc Maximum Efficiency 99.5 % Weighted Efficiency 98.8 % Overvoltage Category II OUTPUT DURING OPERATION (POWER OPTIMIZER CONNECTED TO OPERATING SOLAREDGE INVERTER) Maximum Output Current 15 Adc Maximum Output Voltage 60 85 Vdc OUTPUT DURING STANDBY (POWER OPTIMIZER DISCONNECTED FROM SOLAREDGE INVERTER OR SOLAREDGE INVERTER OFF) Safety Output Voltage per Power Optmizer 1 Vdc STANDARD COMPLIANCE EMC FCC Part15 Class B, IEC61000-6-2, IEC61000-6-3 Safety IEC62109-1 (class II safety), UL1741 RoHS Yes INSTALLATION SPECIFICATIONS Maximum Allowed System Voltage 1000 Vdc Compatble inverters All SolarEdge Single Phase and Three Phase inverters Dimensions (W x L x H) 128 x 152 x 27.5 / 5 x 5.97 x 1.08 128 x 152 x 35 / 5 x 5.97 x 1.37 128 x 152 x 50 / 5 x 5.97 x 1.96 mm / in Weight (including cables) 630 / 1.4 750 / 1.7 845 / 1.9 gr / lb Input Connector MC4 Compatble MC4 / Amphenol AH4 MC4 Compatble Output Wire Type / Connector Double Insulated; MC4 Compatble Double Insulated; MC4 / Amphenol AH4 Double Insulated; MC4 Compatble Output Wire Length 0.95 / 3.0 1.2 / 3.9 m / ﬅ Operatng Temperature Range -40 - +85 / -40 - +185 ˚C / ˚F Protecton Ratng IP68 / NEMA6P Relatve Humidity 0 - 100 % (1) Rated STC power of the module. Module of up to +5% power tolerance allowed. SolarEdge Power Optimizer Module Add-On for North America P300 / P320 / P370 / P400 / P405 PV SYSTEM DESIGN USING A SOLAREDGE INVERTER(2)(3) SINGLE PHASE HD-WAVE SINGLE PHASE THREE PHASE 208V THREE PHASE 480V Minimum String Length (Power Optmizers)8 10 18 Maximum String Length (Power Optmizers)25 25 50 Maximum Power per String 5700 (6000 with SE7600H-US)5250 6000 12750 W Parallel Strings of Different Lengths or Orientatons Yes SolarEdge Single Phase Inverters for North America SE3000H-US / SE3800H-US / SE5000H-US / SE6000H-US / SE7600H-US INVERTERSwww.solaredge.usUSA-CANADA-GERMANY-ITALY-FRANCE-JAPAN-CHINA-AUSTRALIA-THE NETHERLANDS-UK-ISRAEL-TURKEY-SOUTH AFRICA-BULGARIA Optimized installation with HD-Wave technology Specifically designed to work with power optmizers Record-breaking efficiency Integrated Arc Fault protecton and Rapid Shutdown for NEC 2014 and 2017, per artcle 690.11 and 690.12 Extremely small High reliability without any electrolytc capacitors Built-in module-level monitoring Outdoor and indoor installaton Optonal: Revenue grade data, ANSI C12.20 Class 0.5 (0.5% accuracy) 12-25 © SolarEdge Technologies, Inc. All rights reserved. SOLAREDGE, the SolarEdge logo, OPTIMIZED BY SOLAREDGE are trademarks or registered trademarks of SolarEdge Technologies, Inc. All other trademarks mentioned herein are trademarks of their respective owners. Date: 03/2017. V.01. Subject to change without notice. Single Phase Inverters for North America SE3000H-US / SE3800H-US / SE5000H-US / SE6000H-US/ SE7600H-US SE3000H-US SE3800H-US SE5000H-US SE6000H-US SE7600H-US OUTPUT Rated AC Power Output 3000 3800 5000 6000 7600 VA Max. AC Power Output 3000 3800 5000 6000 7600 VA AC Output Voltage Min.-Nom.-Max. (183 - 208 - 229) - - 3 - - Vac AC Output Voltage Min.-Nom.-Max. (211 - 240 - 264) 3 3 3 3 3 Vac AC Frequency (Nominal) 59.3 - 60 - 60.5(1) Hz Maximum Contnuous Output Current 208V - - 24 - - A Maximum Contnuous Output Current 240V 12.5 16 21 25 32 A GFDI Threshold 1 A Utlity Monitoring, Islanding Protecton, Country Configurable Thresholds Yes INPUT Maximum DC Power 4650 5900 7750 9300 11800 W Transformer-less, Ungrounded Yes Maximum Input Voltage 480 Vdc Nominal DC Input Voltage 380 400 Vdc Maximum Input Current 208V - - 15.5 - - Adc Maximum Input Current 240V 8.5 10.5 13.5 16.5 20 Adc Max. Input Short Circuit Current 45 Adc Reverse-Polarity Protecton Yes Ground-Fault Isolaton Detecton 600k Sensitvity Maximum Inverter Efficiency 99 99.2 % CEC Weighted Efficiency 99 % Nightme Power Consumpton < 2.5 W ADDITIONAL FEATURES Supported Communicaton Interfaces RS485, Ethernet, ZigBee (optonal), Cellular (optonal) Revenue Grade Data, ANSI C12.20 Optonal(2) Rapid Shutdown - NEC 2014 and 2017 690.12 Automatc Rapid Shutdown upon AC Grid Disconnect STANDARD COMPLIANCE Safety UL1741, UL1699B, CSA C22.2, Canadian AFCI according to T.I.L. M-07 Grid Connecton Standards IEEE1547, Rule 21(3), Rule 14 (HI) Emissions FCC Part 15 Class B INSTALLATION SPECIFICATIONS AC Output Conduit Size / AWG Range 0.75-1” Conduit / 14-6 AWG DC Input Conduit Size / # of Strings / AWG Range 0.75-1” Conduit /1-2 strings / 14-6 AWG Dimensions with Safety Switch (HxWxD) 17.7 x 14.6 x 6.8 / 450 x 370 x 174 in / mm Weight with Safety Switch 25.3 / 11.5 lb / kg Noise < 25 dBA Cooling Natural Convecton Operatng Temperature Range -13 to +140 / -25 to +60(4) (-40˚F / -40˚C opton)(5) ˚F / ˚C Protecton Ratng NEMA 3R (Inverter with Safety Switch) (1) For other regional setngs please contact SolarEdge support(2) Revenue grade inverter P/N: SExxxxH-US000NNC2(3) Pending certficaton(4) Power de-ratng from 50˚C(5) -40 version P/N: SExxxxH-US000NNU4 Page 1 of 4 3/30/2018 P.O. Box 7627, Avon, CO 81620 | P: 970.306.4233 | F: 866.403.3485 | www.activeenergies.com Solar Installation Information Vendor: Active Energies Solar LLC PO Box 7627 Avon, CO 81620 (970-306-4233 /info@activeenergies.com) Site: Johnson Residence 2401D Upper Traverse Way Vail, CO 81657 Equipment: Panels: 12 Hanwha Q.PEAK DUO BLK-G5 all black solar panels @ 310watts Inverter: 12 SolarEdge P320 Optimizers + 1 SolarEdge SE3000H-US inverter Mounting Equipment: Unirac all black racking system with DPW easy feet mounting feet Monitoring: SolarEdge Remote Energy Monitoring System System Layout: Single Panel = 5.52ft tall X 3.28ft wide Panel Arrangement: 2 rows of 6 with all panels oriented in the portrait position, mounted flush on the west facing roof Holy Cross electric meter located on the east side of the home. Production meter to be located adjacent to the Holy Cross meter. Inverter to be located in the garage. Minimum Designed Temperature: -40°F Maximum Ambient Design Temperature: 140°F All AC wiring to be completed by a Colorado licensed master electrician All DC wiring to be overseen by NABCEP certified installer Unit # 14 Net Meter Production Meter Johnson Residence # 14 Net Meter & Production Meter Page 2 of 4 3/30/2018 P.O. Box 7627, Avon, CO 81620 | P: 970.306.4233 | F: 866.403.3485 | www.activeenergies.com Calculations 3.72kW System Size (STC) Panels: 12 Hanwha Q.PEAK DUO BLK-G5.1 all black solar panels @ 310watts Inverter: 12 SolarEdge P320 Optimizers Inverter: SolarEdge SE3000H-US Inverter (1 string of 12 modules/optimizers) Array tilt angle: 14.04° Array azimuth: 190º (where 180º is south) Estimated annual power production: 5,118kWh Maximum PV System Voltage: 690.7 Voc = 40.02V/module 40.02V x 1 module = 40.02V Temperature correction factor 690.7(A) Temperature Coefficient (Voc) = -0.28%/°C (-65C° x (-.0028C°)) = .182% ((.182% x 40.02V) x 1 panels) + 40.02V = 47.3V Maximum PV Source Circuit (String) Current: 690.8 (A)(1) Isc = 9.83A 9.83A x 1.25 = 12.3A Maximum PV Output Circuit (Array) Current: 690.8 (A)(2) Max Inverter Input Circuit 8.5A Inverter Output Circuit Current: 690.8 (A)(3) 12.5A @ 240V Page 3 of 4 3/30/2018 P.O. Box 7627, Avon, CO 81620 | P: 970.306.4233 | F: 866.403.3485 | www.activeenergies.com Conductor Sizing Roof Pass Thru Box to DC Disconnect/Inverter: Max Inverter Input Circuit 8.5A 8.5A x 125% = 10.6A 690.8 (B)(1) #10 THWN-2 Table 310.16 40A (75ºC column) Conduit fill adjustment Table 310.15 (B)(2)(a) No Conduit Fill Temperature correction factor Table 310.16 No Temperature correction factor From Inverter to AC Disconnect/Production Meter/Backfeed Point: Nameplate maximum continuous output current: 12.5A 12.5A x 125% = 15.6A #10 THWN-2 Table 310.16 30A (75ºC column) No Conduit fill adjustment Table 310.15 (B)(2)(a) No Temperature correction factor Table 310.16 Overcurrent Protection Devices 1 - 20A two pole breaker Backfeed Breaker Conductors may be oversized for Voltage Drop Page 4 of 4 3/30/2018 P.O. Box 7627, Avon, CO 81620 | P: 970.306.4233 | F: 866.403.3485 | www.activeenergies.com SolarEdge SE3000H-US Inverter w/ Integrated Disconnect NEMA 3R Max AC Output: 12.5A @ 240V With ARC Fault Protection & Rapid Shutdown compliant – in the garage DC Grounding Electrode Conductor solid bare #6 Cu, per NEC 250.66(C) Electric Panel Located in garage Line Diagram Johnson Residence 2401D Upper Traverse Way Vail, CO 81657 3.72 kW Utility Interactive Photovoltaic System Modules: 12 x Hanwha Q.PEAK DUO BLK-G5 310 Voc = 40.02V Isc = 9.83A Optimizers: 12 SolarEdge P320 1 String X 12 Modules/Optimizer Inverter: SolarEdge SE3000H-US Operating Voltage: 380V Operating Current: 9.83A Max System Voltage: 480V Max Output Current: 12.5A Tilt Angle: 14.04° Array Azimuth: 190° Production: 5,118kWh/yr Notes: - See Calculation Sheet for conductor sizing. - All conductors are copper unless otherwise noted. - Inverter listed (UL-1741) to de- energize upon loss of utility voltage per NEC 690.61. - Inverter has integral ground-fault protection per NEC 690.5 - 240V 1 Phase Service Panel rating of 200A (bus rating 200 amp and 200 Main disconnect) to accommodate 20A (PV) + 200A (Main) = 220A supply (up to 120% of connected power sources from installations per NEC 705(D)(2)(3)(b) Net MeterPass Thru Box Located on Roof Placard stating ”Photovoltaic System Connected” 2 #10 PV Wire 1# 6G Bare Cu Conductors in Free Air Array mounted on roof 12 Hanwha Q.PEAK DUP BLK-G5 310 Solar Panels 12 SolarEdge P320 DC Optimizers 1 2 3 1212... ~80' ¾” C EMT/PVC 3 #10 THWN-2 1 #10 G THWN-2 Backfeed Breaker 20A 2P 240v ~50' ¾” EMT/MC Cable 2 #10 THWN-2 1 #10 G THWN-2 20A Production Meter Adjacent to net meter ~5' ¾” C EMT/PVC 3 #10 THWN-2 1 #10 G THWN-2 Net meter located on the north side of building 10 Page 1 of 4 3/28/2018 P.O. Box 7627, Avon, CO 81620 | P: 970.306.4233 | F: 866.403.3485 | www.activeenergies.com Solar Installation Information Vendor: Active Energies Solar LLC PO Box 7627 Avon, CO 81620 (970-306-4233 /info@activeenergies.com) Site: Lyttle Residence 2381 B Upper Traverse Way #19 Vail, CO 81657 Equipment: Panels: 15 Hanwha Q.PEAK DUO BLK-G5 all black solar panels @ 310watts Inverter: 15 SolarEdge P320 Optimizers + 1 SolarEdge SE3800H-US inverter Mounting Equipment: Unirac all black racking system with DPW easy feet mounting feet Monitoring: SolarEdge Remote Energy Monitoring System System Layout: Single Panel = 5.52ft tall X 3.28ft wide Panel Arrangement: 2 rows of 5 with all panels oriented in the landscape position and 2 rows of 3/2 in the portrait position all mounted flush to the roof. Holy Cross electric meter located on the south side of the building. Production meter to be located adjacent to the Holy Cross meter. Inverter to be located in the garage. Minimum Designed Temperature: -40°F Maximum Ambient Design Temperature: 140°F All AC wiring to be completed by a Colorado licensed master electrician All DC wiring to be overseen by NABCEP certified installer Unit # 19 Net Meter Production Meter Metcalfe Residence #28 Net Meter & Production Meter Page 2 of 4 3/28/2018 P.O. Box 7627, Avon, CO 81620 | P: 970.306.4233 | F: 866.403.3485 | www.activeenergies.com Calculations 4.65kW System Size (STC) Panels: 15 Hanwha Q.PEAK DUO BLK-G5.1 all black solar panels @ 310watts Inverter: 15 SolarEdge P320 Optimizers Inverter: SolarEdge SE3800H-US Inverter (1 string of 12 modules/optimizers) Array tilt angle: 14.04° Array azimuth: 230º/50º (where 180º is south) Estimated annual power production: 5,541kWh Maximum PV System Voltage: 690.7 Voc = 40.02V/module 40.02V x 1 module = 40.02V Temperature correction factor 690.7(A) Temperature Coefficient (Voc) = -0.28%/°C (-65C° x (-.0028C°)) = .182% ((.182% x 40.02V) x 1 panels) + 40.02V = 47.3V Maximum PV Source Circuit (String) Current: 690.8 (A)(1) Isc = 9.83A 9.83A x 1.25 = 12.3A Maximum PV Output Circuit (Array) Current: 690.8 (A)(2) Max Inverter Input Circuit 10.5A Inverter Output Circuit Current: 690.8 (A)(3) 16A @ 240V Page 3 of 4 3/28/2018 P.O. Box 7627, Avon, CO 81620 | P: 970.306.4233 | F: 866.403.3485 | www.activeenergies.com Conductor Sizing Roof Pass Thru Box to DC Disconnect/Inverter: Max Inverter Input Circuit 10.5A 10.5A x 125% = 13.1A 690.8 (B)(1) #10 THWN-2 Table 310.16 40A (75ºC column) Conduit fill adjustment Table 310.15 (B)(2)(a) No Conduit Fill Temperature correction factor Table 310.16 No Temperature correction factor From Inverter to AC Disconnect/Production Meter/Backfeed Point: Nameplate maximum continuous output current: 12.5A 16A x 125% = 20A #10 THWN-2 Table 310.16 30A (75ºC column) No Conduit fill adjustment Table 310.15 (B)(2)(a) No Temperature correction factor Table 310.16 Overcurrent Protection Devices 1 - 20A two pole breaker Backfeed Breaker Conductors may be oversized for Voltage Drop Page 4 of 4 3/28/2018 P.O. Box 7627, Avon, CO 81620 | P: 970.306.4233 | F: 866.403.3485 | www.activeenergies.com SolarEdge SE3000H-US Inverter w/ Integrated Disconnect NEMA 3R Max AC Output: 12.5A @ 240V With ARC Fault Protection & Rapid Shutdown compliant – in the garage DC Grounding Electrode Conductor solid bare #6 Cu, per NEC 250.66(C) Electric Panel Located in garage Line Diagram Lyttle Residence 2381 B Upper Traverse Way #19 Vail, CO 81657 4.65 kW Utility Interactive Photovoltaic System Modules: 15 x Hanwha Q.PEAK DUO BLK-G5 310 Voc = 40.02V Isc = 9.83A Optimizers: 15 SolarEdge P320 1 String X 15 Modules/Optimizer Inverter: SolarEdge SE3800H-US Operating Voltage: 380V Operating Current: 9.83A Max System Voltage: 480V Max Output Current: 16A Tilt Angle: 14.04° Array Azimuth: 230°/50° Production: 5,541kWh/yr Notes: - See Calculation Sheet for conductor sizing. - All conductors are copper unless otherwise noted. - Inverter listed (UL-1741) to de- energize upon loss of utility voltage per NEC 690.61. - Inverter has integral ground-fault protection per NEC 690.5 - 240V 1 Phase Service Panel rating of 200A (bus rating 200 amp and 200 Main disconnect) to accommodate 20A (PV) + 200A (Main) = 220A supply (up to 120% of connected power sources from installations per NEC 705(D)(2)(3)(b) Net MeterPass Thru Box Located on Roof Placard stating ”Photovoltaic System Connected” 2 #10 PV Wire 1# 6G Bare Cu Conductors in Free Air Array mounted on roof 15 Hanwha Q.PEAK DUP BLK-G5 310 Solar Panels 15 SolarEdge P320 DC Optimizers 1 2 3 1215... ~80' ¾” C EMT/PVC 3 #10 THWN-2 1 #10 G THWN-2 Backfeed Breaker 20A 2P 240v ~50' ¾” EMT/MC Cable 2 #10 THWN-2 1 #10 G THWN-2 20A Production Meter Adjacent to net meter ~5' ¾” C EMT/PVC 3 #10 THWN-2 1 #10 G THWN-2 Net meter located on the south side of building 6 The new Q.PEAK DUO BLK-G5 solar module from Q CELLS impresses with its outstanding visual appearance and particularly high perfor- mance on a small surface thanks to the innovative Q.ANTUM DUO Technology. Q.ANTUM’s world-record-holding cell concept has now been combined with state-of-the-art circuitry half cells and a six- busbar design, thus achieving outstanding performance under real conditions — both with low-intensity solar radiation as well as on hot, clear summer days. THE IDEAL SOLUTION FOR: Rooftop arrays on residential buildings 1 APT test conditions according to IEC/TS 62804-1:2015, method B (−1500 V, 168 h) 2 See data sheet on rear for further information. ANTI PID TECHNOLOGY (APT) HOT-SPOT PROTECT(HSP) TRACEABLE QUALITY (TRA.Q) YIELD SECURITY ANTI LID TECHNOLOGY (ALT) www.VDEinfo.comID. 40032587 Quality Tested high reliability low degradationoptimizeddurabilitycontinous linemonitoring    11/2016 Q.ANTUM TECHNOLOGY: LOW LEVELISED COST OF ELECTRICITY Higher yield per surface area, lower BOS costs, higher power classes, and an efficiency rate of up to 19.3 %. INNOVATIVE ALL-WEATHER TECHNOLOGY Optimal yields, whatever the weather with excellent low-light and temperature behaviour. ENDURING HIGH PERFORMANCE Long-term yield security with Anti LID Technology, Anti PID Technology1, Hot-Spot Protect and Traceable Quality Tra.Q™. EXTREME WEATHER RATING High-tech aluminium alloy frame, certified for high snow (5400 Pa) and wind loads (4000 Pa). A RELIABLE INVESTMENT Inclusive 12-year product warranty and 25-year linear performance warranty2. STATE OF THE ART MODULE TECHNOLOGY Q.ANTUM DUO combines cutting edge cell separation and innovative wiring with Q.ANTUM Technology. Q.PEAK DUO BLK-G5 305-320 Q.ANTUM SOLAR MODULE MECHANICAL SPECIFICATION Format 1685 mm × 1000 mm × 32 mm (including frame) Weight 18.7 kg Front Cover 3.2 mm thermally pre-stressed glass with anti-reflection technology Back Cover Composite film Frame Black anodised aluminium Cell 6 × 20 monocrystalline Q.ANTUM solar half cells Junction box 70-85 mm × 50-70 mm × 13-21 mm Protection class IP67, with bypass diodes Cable 4 mm² Solar cable; (+) 1100 mm, (−) 1100 mm Connector Multi-Contact MC4, IP65 and IP68 QUALIFICATIONS AND CERTIFICATES PARTNER Q CELLS PERFORMANCE WARRANTY PERFORMANCE AT LOW IRRADIANCE TEMPERATURE COEFFICIENTS Temperature Coefficient of ISC α [% / K] + 0.04 Temperature Coefficient of VOC β [% / K] − 0.28 Temperature Coefficient of PMPP γ [% / K] − 0.37 Normal Operating Cell Temperature NOCT [°C] 45 NOTE: Installation instructions must be followed. See the installation and operating manual or contact our technical service department for further information on approved installation and use of this product. IRRADIANCE [W/M2]RELATIVE EFFICIENCYCOMPARED TO NOMINAL POWER [%]100 95 90 85 80 75 15 5 2520 0 10 YEARS 98 Q CELLS Industry standard for tiered warranties* Industry standard for linear warranties* *Standard terms of guarantee for the 10 PV companies with the highest production capacity in 2014 (as at: September 2014) ELECTRICAL CHARACTERISTICS POWER CLASS 305 310 315 320 MINIMUM PERFORMANCE AT STANDARD TEST CONDITIONS, STC1 (POWER TOLERANCE +5 W / −0 W)MinimumPower at MPP2 PMPP [W] 305 310 315 320 Short Circuit Current* ISC [A] 9.78 9.83 9.89 9.94 Open Circuit Voltage* VOC [V] 39.75 40.02 40.29 40.56 Current at MPP* IMPP [A] 9.31 9.36 9.41 9.47 Voltage at MPP* VMPP [V] 32.78 33.12 33.46 33.80 Efficiency2 η [%] ≥ 18.1 ≥ 18.4 ≥ 18.7 ≥ 19.0 MINIMUM PERFORMANCE AT NORMAL OPERATING CONDITIONS, NOC3 Minimum Power at MPP2 PMPP [W] 226.0 229.7 233.5 237.2 Short Circuit Current* ISC [A] 7.88 7.93 7.97 8.02 Open Circuit Voltage* VOC [V] 37.18 37.43 37.69 37.94 Current at MPP* IMPP [A] 7.32 7.36 7.41 7.45 Voltage at MPP* VMPP [V] 30.88 31.20 31.52 31.84 11000 W/m², 25 °C, spectrum AM 1.5 G 2 Measurement tolerances STC ± 3 %; NOC ± 5 % 3 800 W/m², NOCT, spectrum AM 1.5 G * typical values, actual values may differ PROPERTIES FOR SYSTEM DESIGN Maximum System Voltage VSYS [V] 1000 Safety Class II Maximum Reverse Current IR [A] 20 Fire Rating C Push / Pull Load (Test-load in accordance with IEC 61215) [Pa] 5400 / 4000 Permitted Module Temperature On Continuous Duty -40 °C up to +85 °C 200 400 600 800 1000 110 100 90 80RELATIVE EFFICIENCY [%]DETAIL A 16mm 8.5mm24.5mm 980mm 1685mm 4 × Mounting slots (DETAIL A) Frame 1000mm 951mm 32mm 8 × Drainage holes 352.5mm VDE Quality Tested, IEC 61215 (Ed. 2); IEC 61730 (Ed. 1), Application class A This data sheet complies with DIN EN 50380.Specifications subject to technical changes © Hanwha Q CELLS Q.PEAK DUO BLK-G5_305-320_2017-07_Rev01_EN Hanwha Q CELLS GmbH Sonnenallee 17-21, 06766 Bitterfeld-Wolfen, Germany | TEL +49 (0)3494 66 99-23444 | FAX +49 (0)3494 66 99-23000 | EMAIL sales@q-cells.com | WEB www.q-cells.com At least 98 % of nominal power during first year. Thereafter max. 0.54 % degradation per year. At least 93.1 % of nominal power up to 10 years. At least 85 % of nominal power up to 25 years. All data within measurement tolerances. Full warranties in accordance with the warranty terms of the Q CELLS sales organisation of your respective country. Typical module performance under low irradiance conditions in comparison to STC conditions (25 °C, 1000 W/m2). SolarEdge Single Phase Inverters for North America SE3000H-US / SE3800H-US / SE5000H-US / SE6000H-US / SE7600H-US INVERTERSwww.solaredge.usUSA-CANADA-GERMANY-ITALY-FRANCE-JAPAN-CHINA-AUSTRALIA-THE NETHERLANDS-UK-ISRAEL-TURKEY-SOUTH AFRICA-BULGARIA Optimized installation with HD-Wave technology Specifically designed to work with power optmizers Record-breaking efficiency Integrated Arc Fault protecton and Rapid Shutdown for NEC 2014 and 2017, per artcle 690.11 and 690.12 Extremely small High reliability without any electrolytc capacitors Built-in module-level monitoring Outdoor and indoor installaton Optonal: Revenue grade data, ANSI C12.20 Class 0.5 (0.5% accuracy) 12-25 © SolarEdge Technologies, Inc. All rights reserved. SOLAREDGE, the SolarEdge logo, OPTIMIZED BY SOLAREDGE are trademarks or registered trademarks of SolarEdge Technologies, Inc. All other trademarks mentioned herein are trademarks of their respective owners. Date: 03/2017. V.01. Subject to change without notice. Single Phase Inverters for North America SE3000H-US / SE3800H-US / SE5000H-US / SE6000H-US/ SE7600H-US SE3000H-US SE3800H-US SE5000H-US SE6000H-US SE7600H-US OUTPUT Rated AC Power Output 3000 3800 5000 6000 7600 VA Max. AC Power Output 3000 3800 5000 6000 7600 VA AC Output Voltage Min.-Nom.-Max. (183 - 208 - 229) - - 3 - - Vac AC Output Voltage Min.-Nom.-Max. (211 - 240 - 264) 3 3 3 3 3 Vac AC Frequency (Nominal) 59.3 - 60 - 60.5(1) Hz Maximum Contnuous Output Current 208V - - 24 - - A Maximum Contnuous Output Current 240V 12.5 16 21 25 32 A GFDI Threshold 1 A Utlity Monitoring, Islanding Protecton, Country Configurable Thresholds Yes INPUT Maximum DC Power 4650 5900 7750 9300 11800 W Transformer-less, Ungrounded Yes Maximum Input Voltage 480 Vdc Nominal DC Input Voltage 380 400 Vdc Maximum Input Current 208V - - 15.5 - - Adc Maximum Input Current 240V 8.5 10.5 13.5 16.5 20 Adc Max. Input Short Circuit Current 45 Adc Reverse-Polarity Protecton Yes Ground-Fault Isolaton Detecton 600k Sensitvity Maximum Inverter Efficiency 99 99.2 % CEC Weighted Efficiency 99 % Nightme Power Consumpton < 2.5 W ADDITIONAL FEATURES Supported Communicaton Interfaces RS485, Ethernet, ZigBee (optonal), Cellular (optonal) Revenue Grade Data, ANSI C12.20 Optonal(2) Rapid Shutdown - NEC 2014 and 2017 690.12 Automatc Rapid Shutdown upon AC Grid Disconnect STANDARD COMPLIANCE Safety UL1741, UL1699B, CSA C22.2, Canadian AFCI according to T.I.L. M-07 Grid Connecton Standards IEEE1547, Rule 21(3), Rule 14 (HI) Emissions FCC Part 15 Class B INSTALLATION SPECIFICATIONS AC Output Conduit Size / AWG Range 0.75-1” Conduit / 14-6 AWG DC Input Conduit Size / # of Strings / AWG Range 0.75-1” Conduit /1-2 strings / 14-6 AWG Dimensions with Safety Switch (HxWxD) 17.7 x 14.6 x 6.8 / 450 x 370 x 174 in / mm Weight with Safety Switch 25.3 / 11.5 lb / kg Noise < 25 dBA Cooling Natural Convecton Operatng Temperature Range -13 to +140 / -25 to +60(4) (-40˚F / -40˚C opton)(5) ˚F / ˚C Protecton Ratng NEMA 3R (Inverter with Safety Switch) (1) For other regional setngs please contact SolarEdge support(2) Revenue grade inverter P/N: SExxxxH-US000NNC2(3) Pending certficaton(4) Power de-ratng from 50˚C(5) -40 version P/N: SExxxxH-US000NNU4 POWER OPTIMIZERwww.solaredge.usUSA - GERMANY - ITALY - FRANCE - JAPAN - CHINA - ISRAEL - AUSTRALIA SolarEdge Power Optimizer Module Add-On For North America P300 / P400 / P405 Up to 25% more energy Superior efficiency (99.5%) Mitgates all types of module mismatch losses, from manufacturing tolerance to partal shading Flexible system design for maximum space utlizaton Fast installaton with a single bolt Next generaton maintenance with module-level monitoring Module-level voltage shutdown for installer and firefighter safety PV power optimization at the module-level © SolarEdge Technologies, Inc. All rights reserved. SOLAREDGE, the SolarEdge logo, OPTIMIZED BY SOLAREDGE are trademarks or registered trademarks of SolarEdge Technologies, Inc. All other trademarks mentioned herein are trademarks of their respective owners. Date: 09/2014 V.01. Subject to change without notice. (2) It is not allowed to mix P405 with P300/P400/P600/P700 in one string. P300 (for 60-cell modules) P400 (for 72 & 96-cell modules) P405 (for thin film modules) INPUT Rated Input DC Power(1) 300 400 405 W Absolute Maximum Input Voltage (Voc at lowest temperature)48 80 125 Vdc MPPT Operatng Range 8 - 48 8 - 80 12.5 - 105 Vdc Maximum Short Circuit Current (Isc) 10 Adc Maximum DC Input Current 12.5 Adc Maximum Efficiency 99.5 % Weighted Efficiency 98.8 % Overvoltage Category II OUTPUT DURING OPERATION (POWER OPTIMIZER CONNECTED TO OPERATING INVERTER) Maximum Output Current 15 Adc Maximum Output Voltage 60 85 Vdc OUTPUT DURING STANDBY (POWER OPTIMIZER DISCONNECTED FROM INVERTER OR INVERTER OFF) Safety Output Voltage per Power Optmizer 1 Vdc STANDARD COMPLIANCE EMC FCC Part15 Class B, IEC61000-6-2, IEC61000-6-3 Safety IEC62109-1 (class II safety), UL1741 RoHS Yes INSTALLATION SPECIFICATIONS Maximum Allowed System Voltage 1000 Vdc Dimensions (W x L x H) Pxxx-2 series 141 x 212 x 40.5 / 5.55 x 8.34 x 1.59 mm / in Pxxx-5 series 128 x 152 x 27.5 / 5 x 5.97 x 1.08 128 x 152 x 35 / 5 x 5.97 x 1.37 128 x 152 x 48 / 5 x 5.97 x 1.89 mm / in Weight (including cables)Pxxx-2 series 950 / 2.1 gr / lb Pxxx-5 series 770 / 1.7 930 / 2.05 930 / 2.05 gr / lb Input Connector MC4 Compatble Output Wire Type / Connector Double Insulated; Amphenol Output Wire Length 0.95 / 3.0 1.2 / 3.9 m / ﬅ Operatng Temperature Range -40 - +85 / -40 - +185 ˚C / ˚F Protecton Ratng Pxxx-2 series IP65 / NEMA4 Pxxx-5 series IP68 / NEMA6P Relatve Humidity 0 - 100 % (1) Rated STC power of the module. Module of up to +5% power tolerance allowed. SolarEdge Power Optimizer Module Add-On for North America P300 / P400 / P405 PV SYSTEM DESIGN USING A SOLAREDGE INVERTER(2)SINGLE PHASE THREE PHASE 208V THREE PHASE 480V Minimum String Length (Power Optmizers)8 10 18 Maximum String Length (Power Optmizers)25 25 50 Maximum Power per String 5250 6000 12750 W Parallel Strings of Different Lengths or Orientatons Yes Page 1 of 4 3/28/2018 P.O. Box 7627, Avon, CO 81620 | P: 970.306.4233 | F: 866.403.3485 | www.activeenergies.com Solar Installation Information Vendor: Active Energies Solar LLC PO Box 7627 Avon, CO 81620 (970-306-4233 /info@activeenergies.com) Site: Metcalfe Residence 2333B Upper Traverse Way Vail, CO 81657 Equipment: Panels: 12 Hanwha Q.PEAK DUO BLK-G5 all black solar panels @ 310watts Inverter: 12 SolarEdge P320 Optimizers + 1 SolarEdge SE3000H-US inverter Mounting Equipment: Unirac all black racking system with DPW easy feet mounting feet Monitoring: SolarEdge Remote Energy Monitoring System System Layout: Single Panel = 5.52ft tall X 3.28ft wide Panel Arrangement: 2 rows of 6 with all panels oriented in the portrait position, mounted flush on the west facing roof Holy Cross electric meter located on the east side of the home. Production meter to be located adjacent to the Holy Cross meter. Inverter to be located in the garage. Minimum Designed Temperature: -40°F Maximum Ambient Design Temperature: 140°F All AC wiring to be completed by a Colorado licensed master electrician All DC wiring to be overseen by NABCEP certified installer Unit # 28 Net Meter Production Meter Metcalfe Residence #28 Net Meter & Production Meter Page 2 of 4 3/28/2018 P.O. Box 7627, Avon, CO 81620 | P: 970.306.4233 | F: 866.403.3485 | www.activeenergies.com Calculations 3.72kW System Size (STC) Panels: 12 Hanwha Q.PEAK DUO BLK-G5.1 all black solar panels @ 310watts Inverter: 12 SolarEdge P320 Optimizers Inverter: SolarEdge SE3000H-US Inverter (1 string of 12 modules/optimizers) Array tilt angle: 14.04° Array azimuth: 260º (where 180º is south) Estimated annual power production: 4,603kWh Maximum PV System Voltage: 690.7 Voc = 40.02V/module 40.02V x 1 module = 40.02V Temperature correction factor 690.7(A) Temperature Coefficient (Voc) = -0.28%/°C (-65C° x (-.0028C°)) = .182% ((.182% x 40.02V) x 1 panels) + 40.02V = 47.3V Maximum PV Source Circuit (String) Current: 690.8 (A)(1) Isc = 9.83A 9.83A x 1.25 = 12.3A Maximum PV Output Circuit (Array) Current: 690.8 (A)(2) Max Inverter Input Circuit 8.5A Inverter Output Circuit Current: 690.8 (A)(3) 12.5A @ 240V Page 3 of 4 3/28/2018 P.O. Box 7627, Avon, CO 81620 | P: 970.306.4233 | F: 866.403.3485 | www.activeenergies.com Conductor Sizing Roof Pass Thru Box to DC Disconnect/Inverter: Max Inverter Input Circuit 8.5A 8.5A x 125% = 10.6A 690.8 (B)(1) #10 THWN-2 Table 310.16 40A (75ºC column) Conduit fill adjustment Table 310.15 (B)(2)(a) No Conduit Fill Temperature correction factor Table 310.16 No Temperature correction factor From Inverter to AC Disconnect/Production Meter/Backfeed Point: Nameplate maximum continuous output current: 12.5A 12.5A x 125% = 15.6A #10 THWN-2 Table 310.16 30A (75ºC column) No Conduit fill adjustment Table 310.15 (B)(2)(a) No Temperature correction factor Table 310.16 Overcurrent Protection Devices 1 - 20A two pole breaker Backfeed Breaker Conductors may be oversized for Voltage Drop Page 4 of 4 3/28/2018 P.O. Box 7627, Avon, CO 81620 | P: 970.306.4233 | F: 866.403.3485 | www.activeenergies.com SolarEdge SE3000H-US Inverter w/ Integrated Disconnect NEMA 3R Max AC Output: 12.5A @ 240V With ARC Fault Protection & Rapid Shutdown compliant – in the garage DC Grounding Electrode Conductor solid bare #6 Cu, per NEC 250.66(C) Electric Panel Located in garage Line Diagram Metcalfe Residence 2333 B Upper Traverse Way Vail, CO 81657 3.72 kW Utility Interactive Photovoltaic System Modules: 12 x Hanwha Q.PEAK DUO BLK-G5 310 Voc = 40.02V Isc = 9.83A Optimizers: 12 SolarEdge P320 1 String X 12 Modules/Optimizer Inverter: SolarEdge SE3000H-US Operating Voltage: 380V Operating Current: 9.83A Max System Voltage: 480V Max Output Current: 12.5A Tilt Angle: 14.04° Array Azimuth: 260° Production: 4,603kWh/yr Notes: - See Calculation Sheet for conductor sizing. - All conductors are copper unless otherwise noted. - Inverter listed (UL-1741) to de- energize upon loss of utility voltage per NEC 690.61. - Inverter has integral ground-fault protection per NEC 690.5 - 240V 1 Phase Service Panel rating of 200A (bus rating 200 amp and 200 Main disconnect) to accommodate 20A (PV) + 200A (Main) = 220A supply (up to 120% of connected power sources from installations per NEC 705(D)(2)(3)(b) Net MeterPass Thru Box Located on Roof Placard stating ”Photovoltaic System Connected” 2 #10 PV Wire 1# 6G Bare Cu Conductors in Free Air Array mounted on roof 12 Hanwha Q.PEAK DUP BLK-G5 310 Solar Panels 12 SolarEdge P320 DC Optimizers 1 2 3 1212... ~80' ¾” C EMT/PVC 3 #10 THWN-2 1 #10 G THWN-2 Backfeed Breaker 20A 2P 240v ~50' ¾” EMT/MC Cable 2 #10 THWN-2 1 #10 G THWN-2 20A Production Meter Adjacent to net meter ~5' ¾” C EMT/PVC 3 #10 THWN-2 1 #10 G THWN-2 Net meter located on the north side of building 6 The new Q.PEAK DUO BLK-G5 solar module from Q CELLS impresses with its outstanding visual appearance and particularly high perfor- mance on a small surface thanks to the innovative Q.ANTUM DUO Technology. Q.ANTUM’s world-record-holding cell concept has now been combined with state-of-the-art circuitry half cells and a six- busbar design, thus achieving outstanding performance under real conditions — both with low-intensity solar radiation as well as on hot, clear summer days. THE IDEAL SOLUTION FOR: Rooftop arrays on residential buildings 1 APT test conditions according to IEC/TS 62804-1:2015, method B (−1500 V, 168 h) 2 See data sheet on rear for further information. ANTI PID TECHNOLOGY (APT) HOT-SPOT PROTECT(HSP) TRACEABLE QUALITY (TRA.Q) YIELD SECURITY ANTI LID TECHNOLOGY (ALT) www.VDEinfo.comID. 40032587 Quality Tested high reliability low degradationoptimizeddurabilitycontinous linemonitoring    11/2016 Q.ANTUM TECHNOLOGY: LOW LEVELISED COST OF ELECTRICITY Higher yield per surface area, lower BOS costs, higher power classes, and an efficiency rate of up to 19.3 %. INNOVATIVE ALL-WEATHER TECHNOLOGY Optimal yields, whatever the weather with excellent low-light and temperature behaviour. ENDURING HIGH PERFORMANCE Long-term yield security with Anti LID Technology, Anti PID Technology1, Hot-Spot Protect and Traceable Quality Tra.Q™. EXTREME WEATHER RATING High-tech aluminium alloy frame, certified for high snow (5400 Pa) and wind loads (4000 Pa). A RELIABLE INVESTMENT Inclusive 12-year product warranty and 25-year linear performance warranty2. STATE OF THE ART MODULE TECHNOLOGY Q.ANTUM DUO combines cutting edge cell separation and innovative wiring with Q.ANTUM Technology. Q.PEAK DUO BLK-G5 305-320 Q.ANTUM SOLAR MODULE MECHANICAL SPECIFICATION Format 1685 mm × 1000 mm × 32 mm (including frame) Weight 18.7 kg Front Cover 3.2 mm thermally pre-stressed glass with anti-reflection technology Back Cover Composite film Frame Black anodised aluminium Cell 6 × 20 monocrystalline Q.ANTUM solar half cells Junction box 70-85 mm × 50-70 mm × 13-21 mm Protection class IP67, with bypass diodes Cable 4 mm² Solar cable; (+) 1100 mm, (−) 1100 mm Connector Multi-Contact MC4, IP65 and IP68 QUALIFICATIONS AND CERTIFICATES PARTNER Q CELLS PERFORMANCE WARRANTY PERFORMANCE AT LOW IRRADIANCE TEMPERATURE COEFFICIENTS Temperature Coefficient of ISC α [% / K] + 0.04 Temperature Coefficient of VOC β [% / K] − 0.28 Temperature Coefficient of PMPP γ [% / K] − 0.37 Normal Operating Cell Temperature NOCT [°C] 45 NOTE: Installation instructions must be followed. See the installation and operating manual or contact our technical service department for further information on approved installation and use of this product. IRRADIANCE [W/M2]RELATIVE EFFICIENCYCOMPARED TO NOMINAL POWER [%]100 95 90 85 80 75 15 5 2520 0 10 YEARS 98 Q CELLS Industry standard for tiered warranties* Industry standard for linear warranties* *Standard terms of guarantee for the 10 PV companies with the highest production capacity in 2014 (as at: September 2014) ELECTRICAL CHARACTERISTICS POWER CLASS 305 310 315 320 MINIMUM PERFORMANCE AT STANDARD TEST CONDITIONS, STC1 (POWER TOLERANCE +5 W / −0 W)MinimumPower at MPP2 PMPP [W] 305 310 315 320 Short Circuit Current* ISC [A] 9.78 9.83 9.89 9.94 Open Circuit Voltage* VOC [V] 39.75 40.02 40.29 40.56 Current at MPP* IMPP [A] 9.31 9.36 9.41 9.47 Voltage at MPP* VMPP [V] 32.78 33.12 33.46 33.80 Efficiency2 η [%] ≥ 18.1 ≥ 18.4 ≥ 18.7 ≥ 19.0 MINIMUM PERFORMANCE AT NORMAL OPERATING CONDITIONS, NOC3 Minimum Power at MPP2 PMPP [W] 226.0 229.7 233.5 237.2 Short Circuit Current* ISC [A] 7.88 7.93 7.97 8.02 Open Circuit Voltage* VOC [V] 37.18 37.43 37.69 37.94 Current at MPP* IMPP [A] 7.32 7.36 7.41 7.45 Voltage at MPP* VMPP [V] 30.88 31.20 31.52 31.84 11000 W/m², 25 °C, spectrum AM 1.5 G 2 Measurement tolerances STC ± 3 %; NOC ± 5 % 3 800 W/m², NOCT, spectrum AM 1.5 G * typical values, actual values may differ PROPERTIES FOR SYSTEM DESIGN Maximum System Voltage VSYS [V] 1000 Safety Class II Maximum Reverse Current IR [A] 20 Fire Rating C Push / Pull Load (Test-load in accordance with IEC 61215) [Pa] 5400 / 4000 Permitted Module Temperature On Continuous Duty -40 °C up to +85 °C 200 400 600 800 1000 110 100 90 80RELATIVE EFFICIENCY [%]DETAIL A 16mm 8.5mm24.5mm 980mm 1685mm 4 × Mounting slots (DETAIL A) Frame 1000mm 951mm 32mm 8 × Drainage holes 352.5mm VDE Quality Tested, IEC 61215 (Ed. 2); IEC 61730 (Ed. 1), Application class A This data sheet complies with DIN EN 50380.Specifications subject to technical changes © Hanwha Q CELLS Q.PEAK DUO BLK-G5_305-320_2017-07_Rev01_EN Hanwha Q CELLS GmbH Sonnenallee 17-21, 06766 Bitterfeld-Wolfen, Germany | TEL +49 (0)3494 66 99-23444 | FAX +49 (0)3494 66 99-23000 | EMAIL sales@q-cells.com | WEB www.q-cells.com At least 98 % of nominal power during first year. Thereafter max. 0.54 % degradation per year. At least 93.1 % of nominal power up to 10 years. At least 85 % of nominal power up to 25 years. All data within measurement tolerances. Full warranties in accordance with the warranty terms of the Q CELLS sales organisation of your respective country. Typical module performance under low irradiance conditions in comparison to STC conditions (25 °C, 1000 W/m2). SolarEdge Single Phase Inverters for North America SE3000H-US / SE3800H-US / SE5000H-US / SE6000H-US / SE7600H-US INVERTERSwww.solaredge.usUSA-CANADA-GERMANY-ITALY-FRANCE-JAPAN-CHINA-AUSTRALIA-THE NETHERLANDS-UK-ISRAEL-TURKEY-SOUTH AFRICA-BULGARIA Optimized installation with HD-Wave technology Specifically designed to work with power optmizers Record-breaking efficiency Integrated Arc Fault protecton and Rapid Shutdown for NEC 2014 and 2017, per artcle 690.11 and 690.12 Extremely small High reliability without any electrolytc capacitors Built-in module-level monitoring Outdoor and indoor installaton Optonal: Revenue grade data, ANSI C12.20 Class 0.5 (0.5% accuracy) 12-25 © SolarEdge Technologies, Inc. All rights reserved. SOLAREDGE, the SolarEdge logo, OPTIMIZED BY SOLAREDGE are trademarks or registered trademarks of SolarEdge Technologies, Inc. All other trademarks mentioned herein are trademarks of their respective owners. Date: 03/2017. V.01. Subject to change without notice. Single Phase Inverters for North America SE3000H-US / SE3800H-US / SE5000H-US / SE6000H-US/ SE7600H-US SE3000H-US SE3800H-US SE5000H-US SE6000H-US SE7600H-US OUTPUT Rated AC Power Output 3000 3800 5000 6000 7600 VA Max. AC Power Output 3000 3800 5000 6000 7600 VA AC Output Voltage Min.-Nom.-Max. (183 - 208 - 229) - - 3 - - Vac AC Output Voltage Min.-Nom.-Max. (211 - 240 - 264) 3 3 3 3 3 Vac AC Frequency (Nominal) 59.3 - 60 - 60.5(1) Hz Maximum Contnuous Output Current 208V - - 24 - - A Maximum Contnuous Output Current 240V 12.5 16 21 25 32 A GFDI Threshold 1 A Utlity Monitoring, Islanding Protecton, Country Configurable Thresholds Yes INPUT Maximum DC Power 4650 5900 7750 9300 11800 W Transformer-less, Ungrounded Yes Maximum Input Voltage 480 Vdc Nominal DC Input Voltage 380 400 Vdc Maximum Input Current 208V - - 15.5 - - Adc Maximum Input Current 240V 8.5 10.5 13.5 16.5 20 Adc Max. Input Short Circuit Current 45 Adc Reverse-Polarity Protecton Yes Ground-Fault Isolaton Detecton 600k Sensitvity Maximum Inverter Efficiency 99 99.2 % CEC Weighted Efficiency 99 % Nightme Power Consumpton < 2.5 W ADDITIONAL FEATURES Supported Communicaton Interfaces RS485, Ethernet, ZigBee (optonal), Cellular (optonal) Revenue Grade Data, ANSI C12.20 Optonal(2) Rapid Shutdown - NEC 2014 and 2017 690.12 Automatc Rapid Shutdown upon AC Grid Disconnect STANDARD COMPLIANCE Safety UL1741, UL1699B, CSA C22.2, Canadian AFCI according to T.I.L. M-07 Grid Connecton Standards IEEE1547, Rule 21(3), Rule 14 (HI) Emissions FCC Part 15 Class B INSTALLATION SPECIFICATIONS AC Output Conduit Size / AWG Range 0.75-1” Conduit / 14-6 AWG DC Input Conduit Size / # of Strings / AWG Range 0.75-1” Conduit /1-2 strings / 14-6 AWG Dimensions with Safety Switch (HxWxD) 17.7 x 14.6 x 6.8 / 450 x 370 x 174 in / mm Weight with Safety Switch 25.3 / 11.5 lb / kg Noise < 25 dBA Cooling Natural Convecton Operatng Temperature Range -13 to +140 / -25 to +60(4) (-40˚F / -40˚C opton)(5) ˚F / ˚C Protecton Ratng NEMA 3R (Inverter with Safety Switch) (1) For other regional setngs please contact SolarEdge support(2) Revenue grade inverter P/N: SExxxxH-US000NNC2(3) Pending certficaton(4) Power de-ratng from 50˚C(5) -40 version P/N: SExxxxH-US000NNU4 POWER OPTIMIZERwww.solaredge.usUSA - GERMANY - ITALY - FRANCE - JAPAN - CHINA - ISRAEL - AUSTRALIA SolarEdge Power Optimizer Module Add-On For North America P300 / P400 / P405 Up to 25% more energy Superior efficiency (99.5%) Mitgates all types of module mismatch losses, from manufacturing tolerance to partal shading Flexible system design for maximum space utlizaton Fast installaton with a single bolt Next generaton maintenance with module-level monitoring Module-level voltage shutdown for installer and firefighter safety PV power optimization at the module-level © SolarEdge Technologies, Inc. All rights reserved. SOLAREDGE, the SolarEdge logo, OPTIMIZED BY SOLAREDGE are trademarks or registered trademarks of SolarEdge Technologies, Inc. All other trademarks mentioned herein are trademarks of their respective owners. Date: 09/2014 V.01. Subject to change without notice. (2) It is not allowed to mix P405 with P300/P400/P600/P700 in one string. P300 (for 60-cell modules) P400 (for 72 & 96-cell modules) P405 (for thin film modules) INPUT Rated Input DC Power(1) 300 400 405 W Absolute Maximum Input Voltage (Voc at lowest temperature)48 80 125 Vdc MPPT Operatng Range 8 - 48 8 - 80 12.5 - 105 Vdc Maximum Short Circuit Current (Isc) 10 Adc Maximum DC Input Current 12.5 Adc Maximum Efficiency 99.5 % Weighted Efficiency 98.8 % Overvoltage Category II OUTPUT DURING OPERATION (POWER OPTIMIZER CONNECTED TO OPERATING INVERTER) Maximum Output Current 15 Adc Maximum Output Voltage 60 85 Vdc OUTPUT DURING STANDBY (POWER OPTIMIZER DISCONNECTED FROM INVERTER OR INVERTER OFF) Safety Output Voltage per Power Optmizer 1 Vdc STANDARD COMPLIANCE EMC FCC Part15 Class B, IEC61000-6-2, IEC61000-6-3 Safety IEC62109-1 (class II safety), UL1741 RoHS Yes INSTALLATION SPECIFICATIONS Maximum Allowed System Voltage 1000 Vdc Dimensions (W x L x H) Pxxx-2 series 141 x 212 x 40.5 / 5.55 x 8.34 x 1.59 mm / in Pxxx-5 series 128 x 152 x 27.5 / 5 x 5.97 x 1.08 128 x 152 x 35 / 5 x 5.97 x 1.37 128 x 152 x 48 / 5 x 5.97 x 1.89 mm / in Weight (including cables)Pxxx-2 series 950 / 2.1 gr / lb Pxxx-5 series 770 / 1.7 930 / 2.05 930 / 2.05 gr / lb Input Connector MC4 Compatble Output Wire Type / Connector Double Insulated; Amphenol Output Wire Length 0.95 / 3.0 1.2 / 3.9 m / ﬅ Operatng Temperature Range -40 - +85 / -40 - +185 ˚C / ˚F Protecton Ratng Pxxx-2 series IP65 / NEMA4 Pxxx-5 series IP68 / NEMA6P Relatve Humidity 0 - 100 % (1) Rated STC power of the module. Module of up to +5% power tolerance allowed. SolarEdge Power Optimizer Module Add-On for North America P300 / P400 / P405 PV SYSTEM DESIGN USING A SOLAREDGE INVERTER(2)SINGLE PHASE THREE PHASE 208V THREE PHASE 480V Minimum String Length (Power Optmizers)8 10 18 Maximum String Length (Power Optmizers)25 25 50 Maximum Power per String 5250 6000 12750 W Parallel Strings of Different Lengths or Orientatons Yes Page 1 of 4 3/15/2018 P.O. Box 7627, Avon, CO 81620 | P: 970.306.4233 | F: 866.403.3485 | www.activeenergies.com Solar Installation Information Vendor: Active Energies Solar LLC PO Box 7627 Avon, CO 81620 (970-306-4233/info@activeenergies.com) Site: Shubert Residence 2345B Lower Traverse Way Vail, CO 81657 Equipment: Panels: 14 Hanwha Q.PEAK-G4.1 panels @ 310watts Inverter: 14 SolarEdge P320 Optimizers + 1 SolarEdge SE3800H-US inverter Mounting Equipment: Unirac all black racking system with DPW easy feet mounting feet Monitoring: SolarEdge Remote Energy Monitoring System System Layout: Single Panel = 5.48ft tall X 3.28ft wide Panel Arrangement: 2 rows of 7 with all panels oriented in the portrait position, mounted flush on the southwest facing roof Holy Cross electric meter located on the south west side of the building. Production meter to be located adjacent to the Holy Cross meter. Inverter to be located in the garage. Minimum Designed Temperature: -40°F Maximum Ambient Design Temperature: 140°F All AC wiring to be completed by a Colorado licensed master electrician All DC wiring to be overseen by NABCEP certified installer Net Meter and Production Meter Production Meter Unit #12 Net Meter Shubert Residence #12 Page 2 of 4 3/15/2018 P.O. Box 7627, Avon, CO 81620 | P: 970.306.4233 | F: 866.403.3485 | www.activeenergies.com Calculations 4.34kW System Size (STC) Panels: 14 Hanwha Q.PEAK-G4.1 panels @ 310watts Inverter: 14 SolarEdge P320 Optimizers Inverter: SolarEdge SE3800H-US Inverter (1 string of 14 modules/optimizers) Array tilt angle: 14.04° Array azimuth: 230º (where 180º is south) Estimated annual power production: 5,704kWh Maximum PV System Voltage: 690.7 Voc = 40V/module 40V x 1 module = 40V Temperature correction factor 690.7(A) Temperature Coefficient (Voc) = -0.28%/°C (-65C° x (-.0028C°)) = .182% ((.182% x 40V) x 1 panels) + 40V = 47.3V Maximum PV Source Circuit (String) Current: 690.8 (A)(1) Isc = 9.36A 9.36A x 1.25 = 11.7A Maximum PV Output Circuit (Array) Current: 690.8 (A)(2) Max Inverter Input Circuit 10.5A Inverter Output Circuit Current: 690.8 (A)(3) 16A @ 240V Page 3 of 4 3/15/2018 P.O. Box 7627, Avon, CO 81620 | P: 970.306.4233 | F: 866.403.3485 | www.activeenergies.com Conductor Sizing Roof Pass Thru Box to DC Disconnect/Inverter: Max Inverter Input Circuit 10.5A 10.5A x 125% = 13.1A 690.8 (B)(1) #10 THWN-2 Table 310.16 40A (75ºC column) Conduit fill adjustment Table 310.15 (B)(2)(a) No Conduit Fill Temperature correction factor Table 310.16 No temperature correction From Inverter to AC Disconnect/Production Meter/Backfeed Point: Nameplate maximum continuous output current: 16A 16A x 125% = 20A #10 THWN-2 Table 310.16 30A (75ºC column) No Conduit fill adjustment Table 310.15 (B)(2)(a) No Temperature correction factor Table 310.16 Overcurrent Protection Devices 1 - 20A two pole breaker Backfeed Breaker Conductors may be oversized for Voltage Drop Page 4 of 4 3/15/2018 P.O. Box 7627, Avon, CO 81620 | P: 970.306.4233 | F: 866.403.3485 | www.activeenergies.com SolarEdge SE3800H-US Inverter w/ Integrated Disconnect NEMA 3R Max AC Output: 16A @ 240V With ARC Fault Protection & Rapid Shutdown compliant – in the garage DC Grounding Electrode Conductor solid bare #6 Cu, per NEC 250.66(C) Service Panel Located in garage Line Diagram Shubert Residence 2345 B Lower Traverse Way Vail, CO 81657 4.2 kW Utility Interactive Photovoltaic System Modules: 14 Hanwha Qpeak Duo 310w Voc = 40V Isc = 9.36A Optimizers: 14 SolarEdge P370 1 String X 14 Modules/Optimizer Inverter: SolarEdge SE3800H-US Operating Voltage: 380V Operating Current: 15A Max System Voltage: 480V Max Output Current: 16A Tilt Angle: 14.04° Array Azimuth: 230° Production: 5,704kWh/yr Notes: - See Calculation Sheet for conductor sizing. - All conductors are copper unless otherwise noted. - Inverter listed (UL-1741) to de- energize upon loss of utility voltage per NEC 690.61. - Inverter has integral ground-fault protection per NEC 690.5 - 240V 1 Phase Service Panel rating of 200A (bus rating 200 amp and 200 Main disconnect) to accommodate 20A (PV) + 200A (Main) = 220A supply (up to 120% of connected power sources from installations per NEC 705(D)(2)(3)(b) Pass Thru Box Located on Roof Placardstating”PhotovoltaicSystemConnected” 2 #10 PV Wire 1# 6G Bare Cu Conductors in Free Air Array mounted on roof 14 Hawha Q.Peak DUO BLK 310w Solar Panels 14 SolarEdge P320 DC Optimizers 1 2 3 1214... ~5' ¾” C EMT/PVC 3 #10 THWN-2 1 #10 G THWN-2 Backfeed Breaker 20A 2P 240v ~50' ¾” EMT/MC Cable 2 #10 THWN-2 1 #10 G THWN-2 20A Production Meter Adjacent to net meter ~5' ¾” C EMT/PVC 3 #10 THWN-2 1 #10 G THWN-2 Net meter located on the west wall of building #4 The new Q.PEAK DUO BLK-G5 solar module from Q CELLS impresses with its outstanding visual appearance and particularly high perfor- mance on a small surface thanks to the innovative Q.ANTUM DUO Technology. Q.ANTUM’s world-record-holding cell concept has now been combined with state-of-the-art circuitry half cells and a six- busbar design, thus achieving outstanding performance under real conditions — both with low-intensity solar radiation as well as on hot, clear summer days. THE IDEAL SOLUTION FOR: Rooftop arrays on residential buildings 1 APT test conditions according to IEC/TS 62804-1:2015, method B (−1500 V, 168 h) 2 See data sheet on rear for further information. ANTI PID TECHNOLOGY (APT) HOT-SPOT PROTECT(HSP) TRACEABLE QUALITY (TRA.Q) YIELD SECURITY ANTI LID TECHNOLOGY (ALT) www.VDEinfo.comID. 40032587 Quality Tested high reliability low degradationoptimizeddurabilitycontinous linemonitoring    11/2016 Q.ANTUM TECHNOLOGY: LOW LEVELISED COST OF ELECTRICITY Higher yield per surface area, lower BOS costs, higher power classes, and an efficiency rate of up to 19.3 %. INNOVATIVE ALL-WEATHER TECHNOLOGY Optimal yields, whatever the weather with excellent low-light and temperature behaviour. ENDURING HIGH PERFORMANCE Long-term yield security with Anti LID Technology, Anti PID Technology1, Hot-Spot Protect and Traceable Quality Tra.Q™. EXTREME WEATHER RATING High-tech aluminium alloy frame, certified for high snow (5400 Pa) and wind loads (4000 Pa). A RELIABLE INVESTMENT Inclusive 12-year product warranty and 25-year linear performance warranty2. STATE OF THE ART MODULE TECHNOLOGY Q.ANTUM DUO combines cutting edge cell separation and innovative wiring with Q.ANTUM Technology. Q.PEAK DUO BLK-G5 305-320 Q.ANTUM SOLAR MODULE MECHANICAL SPECIFICATION Format 1685 mm × 1000 mm × 32 mm (including frame) Weight 18.7 kg Front Cover 3.2 mm thermally pre-stressed glass with anti-reflection technology Back Cover Composite film Frame Black anodised aluminium Cell 6 × 20 monocrystalline Q.ANTUM solar half cells Junction box 70-85 mm × 50-70 mm × 13-21 mm Protection class IP67, with bypass diodes Cable 4 mm² Solar cable; (+) 1100 mm, (−) 1100 mm Connector Multi-Contact MC4, IP65 and IP68 QUALIFICATIONS AND CERTIFICATES PARTNER Q CELLS PERFORMANCE WARRANTY PERFORMANCE AT LOW IRRADIANCE TEMPERATURE COEFFICIENTS Temperature Coefficient of ISC α [% / K] + 0.04 Temperature Coefficient of VOC β [% / K] − 0.28 Temperature Coefficient of PMPP γ [% / K] − 0.37 Normal Operating Cell Temperature NOCT [°C] 45 NOTE: Installation instructions must be followed. See the installation and operating manual or contact our technical service department for further information on approved installation and use of this product. IRRADIANCE [W/M2]RELATIVE EFFICIENCYCOMPARED TO NOMINAL POWER [%]100 95 90 85 80 75 15 5 2520 0 10 YEARS 98 Q CELLS Industry standard for tiered warranties* Industry standard for linear warranties* *Standard terms of guarantee for the 10 PV companies with the highest production capacity in 2014 (as at: September 2014) ELECTRICAL CHARACTERISTICS POWER CLASS 305 310 315 320 MINIMUM PERFORMANCE AT STANDARD TEST CONDITIONS, STC1 (POWER TOLERANCE +5 W / −0 W)MinimumPower at MPP2 PMPP [W] 305 310 315 320 Short Circuit Current* ISC [A] 9.78 9.83 9.89 9.94 Open Circuit Voltage* VOC [V] 39.75 40.02 40.29 40.56 Current at MPP* IMPP [A] 9.31 9.36 9.41 9.47 Voltage at MPP* VMPP [V] 32.78 33.12 33.46 33.80 Efficiency2 η [%] ≥ 18.1 ≥ 18.4 ≥ 18.7 ≥ 19.0 MINIMUM PERFORMANCE AT NORMAL OPERATING CONDITIONS, NOC3 Minimum Power at MPP2 PMPP [W] 226.0 229.7 233.5 237.2 Short Circuit Current* ISC [A] 7.88 7.93 7.97 8.02 Open Circuit Voltage* VOC [V] 37.18 37.43 37.69 37.94 Current at MPP* IMPP [A] 7.32 7.36 7.41 7.45 Voltage at MPP* VMPP [V] 30.88 31.20 31.52 31.84 11000 W/m², 25 °C, spectrum AM 1.5 G 2 Measurement tolerances STC ± 3 %; NOC ± 5 % 3 800 W/m², NOCT, spectrum AM 1.5 G * typical values, actual values may differ PROPERTIES FOR SYSTEM DESIGN Maximum System Voltage VSYS [V] 1000 Safety Class II Maximum Reverse Current IR [A] 20 Fire Rating C Push / Pull Load (Test-load in accordance with IEC 61215) [Pa] 5400 / 4000 Permitted Module Temperature On Continuous Duty -40 °C up to +85 °C 200 400 600 800 1000 110 100 90 80RELATIVE EFFICIENCY [%]DETAIL A 16mm 8.5mm24.5mm 980mm 1685mm 4 × Mounting slots (DETAIL A) Frame 1000mm 951mm 32mm 8 × Drainage holes 352.5mm VDE Quality Tested, IEC 61215 (Ed. 2); IEC 61730 (Ed. 1), Application class A This data sheet complies with DIN EN 50380.Specifications subject to technical changes © Hanwha Q CELLS Q.PEAK DUO BLK-G5_305-320_2017-07_Rev01_EN Hanwha Q CELLS GmbH Sonnenallee 17-21, 06766 Bitterfeld-Wolfen, Germany | TEL +49 (0)3494 66 99-23444 | FAX +49 (0)3494 66 99-23000 | EMAIL sales@q-cells.com | WEB www.q-cells.com At least 98 % of nominal power during first year. Thereafter max. 0.54 % degradation per year. At least 93.1 % of nominal power up to 10 years. At least 85 % of nominal power up to 25 years. All data within measurement tolerances. Full warranties in accordance with the warranty terms of the Q CELLS sales organisation of your respective country. Typical module performance under low irradiance conditions in comparison to STC conditions (25 °C, 1000 W/m2). POWER OPTIMIZERwww.solaredge.usUSA - GERMANY - ITALY - FRANCE - JAPAN - CHINA - ISRAEL - AUSTRALIA SolarEdge Power Optimizer Module Add-On For North America P300 / P400 / P405 Up to 25% more energy Superior efficiency (99.5%) Mitgates all types of module mismatch losses, from manufacturing tolerance to partal shading Flexible system design for maximum space utlizaton Fast installaton with a single bolt Next generaton maintenance with module-level monitoring Module-level voltage shutdown for installer and firefighter safety PV power optimization at the module-level © SolarEdge Technologies, Inc. All rights reserved. SOLAREDGE, the SolarEdge logo, OPTIMIZED BY SOLAREDGE are trademarks or registered trademarks of SolarEdge Technologies, Inc. All other trademarks mentioned herein are trademarks of their respective owners. Date: 09/2014 V.01. Subject to change without notice. (2) It is not allowed to mix P405 with P300/P400/P600/P700 in one string. P300 (for 60-cell modules) P400 (for 72 & 96-cell modules) P405 (for thin film modules) INPUT Rated Input DC Power(1) 300 400 405 W Absolute Maximum Input Voltage (Voc at lowest temperature)48 80 125 Vdc MPPT Operatng Range 8 - 48 8 - 80 12.5 - 105 Vdc Maximum Short Circuit Current (Isc) 10 Adc Maximum DC Input Current 12.5 Adc Maximum Efficiency 99.5 % Weighted Efficiency 98.8 % Overvoltage Category II OUTPUT DURING OPERATION (POWER OPTIMIZER CONNECTED TO OPERATING INVERTER) Maximum Output Current 15 Adc Maximum Output Voltage 60 85 Vdc OUTPUT DURING STANDBY (POWER OPTIMIZER DISCONNECTED FROM INVERTER OR INVERTER OFF) Safety Output Voltage per Power Optmizer 1 Vdc STANDARD COMPLIANCE EMC FCC Part15 Class B, IEC61000-6-2, IEC61000-6-3 Safety IEC62109-1 (class II safety), UL1741 RoHS Yes INSTALLATION SPECIFICATIONS Maximum Allowed System Voltage 1000 Vdc Dimensions (W x L x H) Pxxx-2 series 141 x 212 x 40.5 / 5.55 x 8.34 x 1.59 mm / in Pxxx-5 series 128 x 152 x 27.5 / 5 x 5.97 x 1.08 128 x 152 x 35 / 5 x 5.97 x 1.37 128 x 152 x 48 / 5 x 5.97 x 1.89 mm / in Weight (including cables)Pxxx-2 series 950 / 2.1 gr / lb Pxxx-5 series 770 / 1.7 930 / 2.05 930 / 2.05 gr / lb Input Connector MC4 Compatble Output Wire Type / Connector Double Insulated; Amphenol Output Wire Length 0.95 / 3.0 1.2 / 3.9 m / ﬅ Operatng Temperature Range -40 - +85 / -40 - +185 ˚C / ˚F Protecton Ratng Pxxx-2 series IP65 / NEMA4 Pxxx-5 series IP68 / NEMA6P Relatve Humidity 0 - 100 % (1) Rated STC power of the module. Module of up to +5% power tolerance allowed. SolarEdge Power Optimizer Module Add-On for North America P300 / P400 / P405 PV SYSTEM DESIGN USING A SOLAREDGE INVERTER(2)SINGLE PHASE THREE PHASE 208V THREE PHASE 480V Minimum String Length (Power Optmizers)8 10 18 Maximum String Length (Power Optmizers)25 25 50 Maximum Power per String 5250 6000 12750 W Parallel Strings of Different Lengths or Orientatons Yes SolarEdge Single Phase Inverters for North America SE3000H-US / SE3800H-US / SE5000H-US / SE6000H-US / SE7600H-US INVERTERSwww.solaredge.usUSA-CANADA-GERMANY-ITALY-FRANCE-JAPAN-CHINA-AUSTRALIA-THE NETHERLANDS-UK-ISRAEL-TURKEY-SOUTH AFRICA-BULGARIA Optimized installation with HD-Wave technology Specifically designed to work with power optmizers Record-breaking efficiency Integrated Arc Fault protecton and Rapid Shutdown for NEC 2014 and 2017, per artcle 690.11 and 690.12 Extremely small High reliability without any electrolytc capacitors Built-in module-level monitoring Outdoor and indoor installaton Optonal: Revenue grade data, ANSI C12.20 Class 0.5 (0.5% accuracy) 12-25 © SolarEdge Technologies, Inc. All rights reserved. SOLAREDGE, the SolarEdge logo, OPTIMIZED BY SOLAREDGE are trademarks or registered trademarks of SolarEdge Technologies, Inc. All other trademarks mentioned herein are trademarks of their respective owners. Date: 03/2017. V.01. Subject to change without notice. Single Phase Inverters for North America SE3000H-US / SE3800H-US / SE5000H-US / SE6000H-US/ SE7600H-US SE3000H-US SE3800H-US SE5000H-US SE6000H-US SE7600H-US OUTPUT Rated AC Power Output 3000 3800 5000 6000 7600 VA Max. AC Power Output 3000 3800 5000 6000 7600 VA AC Output Voltage Min.-Nom.-Max. (183 - 208 - 229) - - 3 - - Vac AC Output Voltage Min.-Nom.-Max. (211 - 240 - 264) 3 3 3 3 3 Vac AC Frequency (Nominal) 59.3 - 60 - 60.5(1) Hz Maximum Contnuous Output Current 208V - - 24 - - A Maximum Contnuous Output Current 240V 12.5 16 21 25 32 A GFDI Threshold 1 A Utlity Monitoring, Islanding Protecton, Country Configurable Thresholds Yes INPUT Maximum DC Power 4650 5900 7750 9300 11800 W Transformer-less, Ungrounded Yes Maximum Input Voltage 480 Vdc Nominal DC Input Voltage 380 400 Vdc Maximum Input Current 208V - - 15.5 - - Adc Maximum Input Current 240V 8.5 10.5 13.5 16.5 20 Adc Max. Input Short Circuit Current 45 Adc Reverse-Polarity Protecton Yes Ground-Fault Isolaton Detecton 600k Sensitvity Maximum Inverter Efficiency 99 99.2 % CEC Weighted Efficiency 99 % Nightme Power Consumpton < 2.5 W ADDITIONAL FEATURES Supported Communicaton Interfaces RS485, Ethernet, ZigBee (optonal), Cellular (optonal) Revenue Grade Data, ANSI C12.20 Optonal(2) Rapid Shutdown - NEC 2014 and 2017 690.12 Automatc Rapid Shutdown upon AC Grid Disconnect STANDARD COMPLIANCE Safety UL1741, UL1699B, CSA C22.2, Canadian AFCI according to T.I.L. M-07 Grid Connecton Standards IEEE1547, Rule 21(3), Rule 14 (HI) Emissions FCC Part 15 Class B INSTALLATION SPECIFICATIONS AC Output Conduit Size / AWG Range 0.75-1” Conduit / 14-6 AWG DC Input Conduit Size / # of Strings / AWG Range 0.75-1” Conduit /1-2 strings / 14-6 AWG Dimensions with Safety Switch (HxWxD) 17.7 x 14.6 x 6.8 / 450 x 370 x 174 in / mm Weight with Safety Switch 25.3 / 11.5 lb / kg Noise < 25 dBA Cooling Natural Convecton Operatng Temperature Range -13 to +140 / -25 to +60(4) (-40˚F / -40˚C opton)(5) ˚F / ˚C Protecton Ratng NEMA 3R (Inverter with Safety Switch) (1) For other regional setngs please contact SolarEdge support(2) Revenue grade inverter P/N: SExxxxH-US000NNC2(3) Pending certficaton(4) Power de-ratng from 50˚C(5) -40 version P/N: SExxxxH-US000NNU4